COOSPO X1

Contents

COOSPO X1 Mini Electric Bike Pump User Manual

Model: X1 | Brand: COOSPO

Introduction

The COOSPO X1 Mini Electric Bike Pump is a compact and efficient digital inflator designed for a variety of uses, including bicycle tires (MTB, road bikes), motorcycle tires, and sports balls. This portable device features a digital display for real-time pressure monitoring, automatic pressure detection, and an auto-stop function for precise inflation. Its lightweight design and rechargeable battery make it an ideal companion for on-the-go inflation needs.

COOSPO X1 Air Pump held in hand with accessories
Image: The COOSPO X1 Mini Electric Bike Pump shown held in hand with its accessories.

For a comprehensive guide, please refer to the official user manual PDF: User Manual (PDF).

Key Features

  • Smart Inflation: Auto calibration, preset tire pressure, auto stop when fully inflated, high-pressure start for quick top-ups, and automatic pressure detection.
  • Efficient Heat Dissipation: Designed for safer operation without the need for a silicone case.
  • Dynamic Balancing Technology: Minimizes vibration, heat, noise, and energy loss, boosting inflation speed and battery life.
  • Compact & Lightweight: Pocket-sized and only 120g, making it highly portable.
  • Fast Charging: Type-C fast charging, fully charges in approximately 40 minutes.
COOSPO X1 Smarter Features: Auto calibration, auto stop, high-pressure start, automatic pressure detection
Image: Illustration of the pump's smart features including auto calibration and automatic pressure detection.
COOSPO X1 Efficient Heat Dissipation Diagram
Image: Diagram illustrating the efficient heat dissipation mechanism of the COOSPO X1 pump.

Setup

Package Contents

Before first use, please check the package contents:

  • COOSPO X1 Mini Electric Bike Pump
  • Presta Valve Adapter (×1)
  • Needle Valve (×1)
  • Charging Cable (USB Type-C) (×1)
  • High-Pressure Hose (with Schrader Valve x1)
  • User Manual
COOSPO X1 Air Pump Package Contents
Image: COOSPO X1 Air Pump and its included accessories.

Initial Charging

Before using the pump for the first time, fully charge it. Connect the provided USB Type-C charging cable to a 5V USB adapter (not included) and plug it into the pump.

  • Charging Status: The battery indicator on the display will flash.
  • Fully Charged: The battery indicator will stop flashing (pump is off).

Note: The pump is off during charging and cannot be used. Please purchase a safety-approved adapter separately.

Type-C Fast Charging for COOSPO X1
Image: Illustration of the pump being charged via Type-C, highlighting fast charging capabilities.

Operating Instructions

Power On/Off

  • Power On: Press and hold the Power/Start/Stop button for about 2 seconds.
  • Power Off: Press and hold the Power/Start/Stop button. The pump will also turn off automatically after 3 minutes of inactivity.

Understanding the Display and Controls

COOSPO X1 Real-time Pressure Display and Button Functions
Image: Diagram showing the digital display for real-time/preset pressure and battery level, along with the '+', 'Power/Start/Stop', and '-' buttons.
  • Display: Shows real-time pressure, preset pressure, and battery level.
  • '+' Button: Increases preset pressure.
  • 'Power/Start/Stop' Button: Powers on/off, starts/stops inflation.
  • '-' Button: Decreases preset pressure.

Nozzle Connection and Inflation

The COOSPO X1 is compatible with Presta and Schrader valves, and includes a needle valve for sports balls.

COOSPO X1 Wide Compatibility with Presta, Schrader, and Ball Valves
Image: Diagrams illustrating how to connect the pump to Presta, Schrader, and ball valves using the appropriate adapters.
  1. Presta Valve: Connect the pump nozzle directly to the Presta valve. Keep the nozzle pressed tightly during inflation. Note: Before using, screw the tire valve nut to the top and secure it.
  2. Schrader Valve: Connect the pump nozzle to the included high-pressure hose, then connect the hose to the tire's Schrader valve.
  3. Needle Valve (for balls): Connect the pump nozzle to the needle valve or the high-pressure hose with the needle valve, then insert the needle valve into the ball's inflation hole.

Pressure Detection

When the pump is powered on, connect it to the object you wish to inflate. The display will show the current pressure. The pump's pressure measuring range is 3-150 psi.

Preset Inflation Pressure

The inflation pressure range is 3-120 psi. You can adjust the preset pressure before inflating:

  • Short press "+" or "-" to adjust the pressure incrementally.
  • Long press "+" or "-" for quick adjustment.

When adjusting, the number will flash. Once set, the value is saved and will display the last set pressure when the pump is turned on.

Inflation Operation

In the powered-on state, press the Power/Start/Stop button to begin inflating. The display will show the real-time pressure. If there is no pressure change for over one minute, inflation will stop automatically. The pump will also stop automatically when the preset pressure is reached.

Caution: During inflation, the noise level is about 80dB. Please take precautions. The nozzle and hose may become hot after inflation; handle with care to avoid burns. A small amount of air may leak when removing the nozzle; do so quickly.

Video: Demonstration of the COOSPO X1 Mini Electric Bike Pump in use, showing its portability and inflation process.

Performance Reference

The COOSPO X1 offers efficient inflation for various items. Below are typical performance figures (laboratory data, actual results may vary based on environment and factors).

COOSPO X1 Inflatable Performance Reference Table
Image: Table detailing inflation quantity and speed for Road bikes (700 x 23C), MTB (27.5 x 1.95), and Balls at different PSI ranges.
COOSPO X1 Inflatable Performance Reference
TypePSI RangeInflation QuantityInflation Speed Each Tire/Item
Road bike (700 x 23C)0~80 PSI≈ 5 Tires≈ 50s
0~90 PSI≈ 5 Tires≈ 59s
0~100 PSI≈ 5 Tires≈ 68s
0~110 PSI≈ 4 Tires≈ 90s
0~120 PSI≈ 2 Tires≈ 98s
MTB (27.5 x 1.95)0~50 PSI≈ 3 Tires≈ 80s
Ball0~7 PSI≈ 19 Pcs≈ 30s

*Laboratory data, and may vary due to changes in test environment, conditions and other factors.

Common Product Pressure Values

The recommended pressure range for various product types is for reference only. Always follow the guidelines in the product's manual for accurate pressure requirements.

Recommended Pressure Values
Product CategoryProduct TypeRecommended Pressure Range
Bicycles12", 14", 16" Bicycle Tires30-50psi
20", 22", 24" Bicycle Tires40-50psi
26", 27.5", 29" Mountain Bike Tires45-65psi
700c Road Bike Clincher Tires100-120psi
700c Road Bike Tubular Tires110-120psi
MotorcycleMotorcycle & electric motorcycle tires26-44psi
Electric bicycleElectric bicycle tires(Refer to tire sidewall)

Note: The recommended tire pressure for bicycles, e-bikes, some motorcycles, and scooters is marked on the tire sidewall. Pressure depends on the load weight. For best results and safety, refer to the product manual.

Common Unit Conversion:

  • 1 bar = 14.5 psi
  • 1 bar = 100 kPa
  • 1 psi ≈ 1 lbs (Data sourced from the laboratory)

Maintenance

Battery Care

  • Do not disassemble, hit, squeeze, or cut the battery, as this may cause explosion or leakage.
  • If the battery shows obvious swelling, stop using it immediately and dispose of it properly.
  • Ensure the battery compartment is securely closed. If it cannot close completely, stop using the device and keep it away from children.
  • Battery disposal: Do not throw the battery in regular trash. Follow local regulations and take used batteries to a professional recycling facility for safe disposal.
  • Storage temperature: -10°C to 45°C. Extreme cold or heat may shorten battery life.
  • If not used for over 3 months, it is recommended to charge it once.

General Care

  • This product is not a toy and should not be used by children. It is recommended for users aged 16 and above.
  • Do not dispose of the pump or expose it to direct sunlight. Avoid overheating, impact, or water to prevent fire or explosion.
  • If the product makes unusual sounds or gets too hot, turn it off immediately.
  • During inflation, monitor the process to avoid overinflation.
  • Use a qualified adapter and the original charging cable for charging.

Troubleshooting

ProblemSolution
Slow Inflation Speed
  • Check if the battery has enough charge.
  • Check if the hose is leaking.
  • Ensure the nozzle and hose connections are tightly screwed.
  • Check if the item being inflated is leaking.
Unable to Inflate After Powering On
  • Check if the battery has enough charge.
  • Check if the current tire pressure is higher than the preset value.
Normal Inflation but Pressure Shows ZeroLow-pressure items, such as balloons, are not within the pump's measuring range.
Pump Turns Off Automatically After Nozzle is TightenedPress and hold the power/start/stop button to turn the pump back on.
Air Leakage When Connecting the HoseTighten the nozzle securely.
Battery Indicator Color Changes During InflationThe battery voltage drops during use, which may cause the indicator light to change or dim. This is normal and not a malfunction.
Unable to Power OnMake sure the battery is fully charged.
Unable to Inflate / Unable to Detect Pressure
  • Ensure the correct nozzle interface is being used.
  • If using a Presta valve, make sure the tire valve core screw is loosened.
  • If using a Schrader valve, ensure the tire valve core is clean.
Error Code H, LThe temperature is out of range. Let the pump cool at room temperature for 1 hour before using.
Error Code E1The pressure is out of range. Remove the nozzle to see if it resets. If the error code disappears, check if the inflated item's pressure exceeds the range.

Specifications

ParameterValue
Product NameMini Bike Pump
Product ModelAP-X1
Product Dimensions72*53*30mm
Weight120g
Inflation Pressure Range3-120psi
Pressure Measurement Range3-150psi
Sensor Accuracy±1psi
Battery Capacity500mAh (3.7Wh)
Charging PortUSB Type-C
Input Parameters5V-2A
Charging TimeLess than 1 hour (approx. 40 minutes for full charge)
Operating Noise80 dB at 1 meter distance
Storage Temperature-10°C to 45°C
Operating Temperature (Charging)0°C to 45°C
Operating Temperature (Discharging)-10°C to 45°C
Screen Size16.25*14mm
CertificationCE
COOSPO X1 Pocket Size and Dimensions
Image: Visual representation of the pump's compact size (72x53x30mm) and light weight (120g).

User Tips

  • Portability: The COOSPO X1 is designed to be lightweight (120g) and compact (72x53x30mm), making it easy to carry in a jersey pocket or bike bag for emergencies.
  • Pre-ride Check: Always ensure the pump is fully charged before a long ride to maximize its inflation capacity.
  • Valve Compatibility: Remember to loosen the Presta valve core screw before attaching the pump for proper inflation.

Warranty and Support

For further product details, support, or inquiries, please contact COOSPO directly.

If product is operating improperly, call COOSPO support. Product must be returned to the manufacturer for any service or repair.

Safety Information and Compliance

General Safety Precautions

  • Do not open or modify the product.
  • Do not disassemble or attempt to service this product yourself.
  • This product is safe under normal and reasonably foreseeable operating conditions.
  • Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Contact your local government or a retailer for additional information.

FCC Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

  1. This device may not cause harmful interference.
  2. This device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.