MOTOHANS CG150

Contents

MOTOHANS CG150 62MM 125CC Cylinder Kit Instruction Manual

For ATV, Dirt Bike, and Scooter Engines (Loncin, Lifan, Zongshen, FT150, DT150, DM150, FORZA150, GY150)

1. Introduction

This manual provides essential information for the proper installation, operation, and maintenance of your MOTOHANS CG150 62MM 125CC Cylinder Kit. This kit is designed for various motorcycle, scooter, ATV, and pocket bike engines, including models from Loncin, Lifan, and Zongshen, specifically FT150, DT150, DM150, FORZA150, and GY150. Please read this manual thoroughly before attempting any installation or use to ensure safety and optimal performance.

2. Important Safety Warnings

  • Compatibility Check: Always confirm that the parts in this kit are compatible with your specific motorcycle, scooter, ATV, or pocket bike model before installation. Refer to the specifications section and compare with your existing components.
  • Professional Installation Recommended: Installation of engine components can be complex and may require specialized tools and knowledge. It is highly recommended that installation be performed by a qualified mechanic or experienced individual. Improper installation can lead to engine damage, personal injury, or voiding of warranties.
  • Modifications: Some applications may require minor modifications to your vehicle or engine. If you are not comfortable performing such modifications, seek professional assistance.
  • Contact for Clarification: If you are unsure about compatibility or any installation steps, please contact MOTOHANS customer support for assistance before proceeding.

3. Product Overview

The CG150 Cylinder Kit includes the following components:

  • Cylinder Barrel (62mm bore)
  • Piston (available in 15mm or 13mm pin versions)
  • Piston Pin
  • Piston Rings
  • Circlips
  • Gasket Set (Head Gasket, Base Gasket)

Below are visual representations of the kit components and their key dimensions:

CG150 Cylinder Kit with 15mm Piston Pin

Figure 3.1: Complete CG150 Cylinder Kit (15mm Piston Pin version) showing cylinder, piston, pin, rings, and gaskets. Bore size: 62mm, Pin size: 15mm.

CG150 Cylinder Kit with 13mm Piston Pin

Figure 3.2: Complete CG150 Cylinder Kit (13mm Piston Pin version) showing cylinder, piston, pin, rings, and gaskets. Bore size: 62mm, Pin size: 13mm.

CG150 Piston with 15mm Pin and Rings Dimensions

Figure 3.3: Detailed view of the 15mm piston, pin (φ15*50mm), and piston rings (1.2*1.2*2.5mm). Piston bore: 62mm, Piston height: 52mm.

CG150 Piston with 13mm Pin and Rings Dimensions

Figure 3.4: Detailed view of the 13mm piston, pin (φ13*45.5mm), and piston rings (0.8*0.8*1.5mm). Piston bore: 62mm, Piston height: 40mm.

CG150 Cylinder Dimensions

Figure 3.5: Various views of the CG150 cylinder with key dimensions, including overall height (97.5mm), width (68.7mm), bore (62mm), outer diameter (67.6mm), and bolt pattern measurements.

4. Specifications

AttributeValue
Brand NameMOTOHANS
Model NameCG150
MaterialAluminum
OriginMainland China
Bore Size62MM
Piston Pin (Normal)15MM PIN (φ15*50mm)
Piston Ring (for 15mm pin)1.2*1.2*2.5mm
Piston Height (for 15mm pin)52mm
Piston Pin (Short)13MM PIN (φ13*45.5mm)
Piston Ring (for 13mm pin)0.8*0.8*1.5mm
Piston Height (for 13mm pin)40mm
Cylinder Overall Height97.5mm
Cylinder Outer Diameter67.6mm
Cylinder Exhaust Port Diameterφ22.5mm

5. Installation (Setup)

Installing a cylinder kit requires mechanical expertise. If you are not confident in your abilities, please consult a professional mechanic.

General Installation Steps:

  1. Preparation: Ensure the engine is clean and free of debris. Gather all necessary tools, including torque wrenches, piston ring compressors, and appropriate lubricants.
  2. Disassembly: Carefully remove the old cylinder, piston, and gaskets. Pay attention to the orientation of all components.
  3. Inspection: Inspect the crankcase and connecting rod for any damage or wear. Clean all mating surfaces thoroughly to ensure a proper seal with the new gaskets.
  4. Piston Assembly: Install the piston rings onto the new piston according to the manufacturer's specifications (refer to Figure 3.3 or 3.4 for ring dimensions). Ensure the ring gaps are correctly spaced. Attach the piston to the connecting rod using the piston pin and circlips.
  5. Cylinder Installation: Lubricate the piston and cylinder bore with engine oil. Using a piston ring compressor, carefully slide the cylinder over the piston, ensuring the rings do not catch or break.
  6. Gasket Placement: Place the new base gasket and head gasket in their correct positions.
  7. Final Assembly: Install the cylinder head and torque all bolts to the manufacturer's specified values. Reconnect all hoses, wires, and other components.
  8. Fluid Check: Refill engine oil and coolant (if applicable) to the correct levels.

Refer to your vehicle's service manual for specific torque values and detailed assembly procedures.

6. Operating Considerations

After installing a new cylinder kit, proper break-in is crucial for engine longevity and performance.

Break-in Procedure:

  • Initial Start-up: Start the engine and allow it to idle for a few minutes. Check for any leaks or unusual noises.
  • Gentle Riding: For the first 100-200 miles (160-320 km), avoid high RPMs, sudden acceleration, and prolonged periods at a constant speed. Vary engine speed frequently.
  • Oil Changes: Consider an early oil change after the initial break-in period to remove any manufacturing debris or wear particles.
  • Monitoring: Continuously monitor engine temperature and performance during the break-in period.

7. Maintenance

Regular maintenance is essential to ensure the longevity and optimal performance of your engine and the new cylinder kit.

  • Oil Changes: Follow your vehicle manufacturer's recommendations for regular engine oil changes. Use high-quality engine oil.
  • Air Filter: Regularly inspect and clean or replace the air filter to prevent contaminants from entering the engine.
  • Spark Plug: Check and replace the spark plug as recommended to ensure efficient combustion.
  • Valve Clearance: Periodically check and adjust valve clearances according to your engine's specifications.
  • Cooling System: Ensure the cooling system (if liquid-cooled) is properly maintained, with adequate coolant levels and no leaks.
  • General Inspection: Periodically inspect the cylinder and piston for any signs of wear, damage, or leaks.

8. Troubleshooting

If you encounter issues after installing the cylinder kit, consider the following common problems and solutions:

ProblemPossible CauseSolution
Loss of CompressionImproperly seated piston rings, damaged gaskets, incorrect valve clearance.Recheck piston ring installation, replace gaskets, adjust valve clearance.
Engine OverheatingInsufficient break-in, lean fuel mixture, cooling system issues.Ensure proper break-in, check carburetor/fuel injection, inspect cooling system.
Unusual Engine NoisesLoose components, incorrect assembly, piston slap.Recheck all fasteners, verify assembly steps, consult a professional.
Oil LeaksDamaged or improperly installed gaskets.Inspect and replace gaskets, ensure mating surfaces are clean.

For persistent issues, it is always best to consult a professional mechanic.

9. User Tips

  • Double-Check Pin Size: Before ordering, carefully measure your existing piston pin to ensure you select the correct 15mm or 13mm pin version of the kit. This is a critical compatibility point.
  • Gasket Sealing: Always use new gaskets provided in the kit and ensure all mating surfaces are perfectly clean and flat for an optimal seal.
  • Lubrication: Generously lubricate the piston, rings, and cylinder bore with fresh engine oil during assembly to prevent dry starts and reduce initial wear.

10. Warranty & Support

MOTOHANS is committed to providing quality products. If you encounter any problems with your cylinder kit, such as damage, defects, or if you received an incorrect product, please contact our customer support team immediately. We will work with you to find a satisfactory solution.

Please provide details of the issue and your purchase information when contacting support. We do not accept disputes without prior communication and an attempt to resolve the issue directly.

As a professional motorcycle parts supplier, we also offer wholesale opportunities. If you own a shop and are interested in long-term business, please contact us.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.