1. Safety Information
This manual is intended primarily for use by professional bicycle mechanics. Users who are not professionally trained for bicycle assembly should not attempt to install the components themselves. If any part of the information is unclear, contact your place of purchase or a local bicycle dealer for assistance.
Always read all instruction manuals included with the product. Do not disassemble or modify the product other than as stated in this manual.
All manuals and technical documents are accessible online at https://si.shimano.com.
DANGER
Failure to follow the instructions will result in death or serious injury.
WARNING
- Failure to follow the instructions could result in death or serious injury.
- Wear approved eye protection while performing maintenance tasks such as replacing components.
- Because each bicycle may handle slightly differently depending on the model, be sure to learn the proper braking technique (including brake lever pressure and bicycle control characteristics) and operation of your bicycle. Improper use of your bicycle's brake system may result in a loss of control or a fall, which could lead to severe injury.
- When using a lever with mode switching mechanism, follow the figure to select the correct mode. If the incorrect mode is selected it may result in either excessive or insufficient braking force, which is highly dangerous.
- Do not apply the front brake too strongly. If you do so, the wheel may lock and the bicycle may fall forward, and serious injury may result.
- Because the required braking distance will be longer during wet weather, reduce your speed and apply the brakes early and gently. You may fall or collide and be seriously injured.
- A wet road surface may cause tires to skid; therefore, to avoid this, reduce your speed and apply the brakes early and gently. If the tires skid, you may fall and be seriously injured.
CAUTION
Failure to follow the instructions could cause personal injury or physical damage to equipment and surroundings.
Brake Lever Mode Positions
The ST-EF500-L4A/ST-EF500-2L4A/ST-EF500-7R4A/ST-EF500-8R4A/ST-EF510-L4A/ST-EF510-7R4A/ST-EF510-8R4A (four finger) brake levers are equipped with a mechanism to make them compatible with V-BRAKE brakes, which contain a power modulator, cantilever and roller brakes. Assemble them as shown in the figure.
| Mode Position | Applicable Brake |
|---|---|
|
C/R position
|
|
|
V position
|
|
Diagram showing brake lever mode positions for C/R and V settings.
2. Tools Required
The following tools are needed for installation, adjustment, and maintenance purposes:
| Tool | Description |
|---|---|
| 5 mm hexagon wrench | For securing components to handlebars. |
| Screwdriver [#1] | General purpose screwdriver. |
| Screwdriver [#2] | For lever stroke adjustment. |
| TL-CT12 cable cutter | For cutting inner and outer cables. |
3. Setup and Installation
This section details the installation process for the SHIMANO Tourney 3x7 Speed Groupset components.
3.1. Installation to the Handlebars
- Secure the shifter/brake lever to the handlebars using the clamp screw. The tools and tightening torque vary depending on the product.
- Tighten to a tightening torque that matches the tool size (typically 6-8 N-m for a 5 mm hexagon wrench).
- Use a handlebar grip with an outer diameter of Ø32 mm or less.
Diagram showing installation of shifter/brake lever to handlebars.
3.2. Installation of the Brake Cable
- Pull the brake lever in the direction of brake operation.
- Set the inner end of the brake cable in the cable hook and pass it through the brake cable housing.
- Run the brake cable through the slit to set it in place.
Diagram showing brake cable installation steps.
3.3. Installing the Shifting Cable
Cable Used:
- Inner cable: Stainless steel, Ø1.2 mm
- Outer casing: SP40 outer casing, Ø4 mm
Use a cable which still has some length to spare even when the handlebars are turned all the way to both sides. Ensure the shifting lever does not touch the bicycle frame when the handlebars are turned all the way.
Use the specified cable and cable guide for smooth operation.
Grease with SIS SP41 grease (Y04180000) the inner cable and the sliding portions of the outer casing before use to ensure that they slide properly.
Using a frame with internal cable routing is strongly discouraged as it has tendencies to impair the SIS shifting function due to its high cable resistance.
A special grease is used for the gear shifting cable. Do not use Premium Grease or other types of grease, otherwise, they may cause deterioration in gear shifting performance.
Cutting the Outer Casing:
- Use a cable cutter (TL-CT12) or an equivalent tool to cut the side opposite of the inscription. Be careful not to injure your hand with the TL-CT12 needle section.
- After cutting, expand the tip of the liner (Ø 2.2 or more) with TL-CT12 or another narrow tool. Arrange the cut end into a perfect circle.
- Attach the same outer end cap to the cut end of the outer casing.
Diagram showing cable cutting and preparation.
Installing to the Dual Control Lever:
- For the left-hand lever, operate the lever two times or more to set it to the initial position. For the right-hand lever, operate the lever seven times or more to set it to the initial position. (The number of times differs depending on the model.)
- Remove the screws, then remove the cover.
- Remove the indicator, then install the inner cable. Run the inner cable through the outer casing.
- Install the indicator to the rotating body.
- Install the cover. Tighten screws to 0.25-0.5 N-m.
Diagram showing installation of shifting cable to dual control lever.
4. Adjustment
4.1. Lever Stroke Adjustment
Lever stroke adjustment can be carried out using a Screwdriver [#2] in the following ways:
- Clockwise: The lever stroke becomes smaller.
- Counterclockwise: The lever stroke becomes larger.
Diagram showing lever stroke adjustment point.
4.2. Adjusting the Inner Cable
When a cable adjuster is provided:
- The adjustment margin for the cable adjuster is five turns from its fully-tightened position.
- The adjuster is initially tightened to the point where it is 1 turn loose of the fully-tightened state.
- To loosen (stretches the cable): Turn the adjuster.
- To tighten: Turn the adjuster.
Diagram showing inner cable adjustment point.
5. Maintenance
5.1. Replacing the Inner Cable
- Operate lever (B) to set the chain on the smallest chainring and the smallest sprocket.
- Unscrew the screws to remove the cover.
- Remove the indicator, then pull out the inner cable and follow by installing a new inner cable.
- Install the indicator to the rotating body.
- Install the cover. Tighten screws to 0.25-0.5 N-m.
Diagram showing steps for replacing the inner cable.
6. Troubleshooting
If you encounter issues with gear shifting adjustments, consider the following:
- Gear Shifting Issues: If gear shifting adjustments cannot be carried out effectively, check the alignment of the dropout. Also, verify if the cable is properly lubricated and if the outer casing is of the correct length (not too long or too short).
- Brake Performance: Ensure the brake levers are set to the correct mode (C/R or V) for your specific brake type to avoid insufficient or excessive braking force.
7. Specifications
7.1. General Product Specifications
| Attribute | Value |
|---|---|
| Brand Name | SHIMANO |
| Derailleur Groupset Type | Mechanical Derailleur system |
| Gears | 21 Speed (3x7) |
| Material | Alloy |
| Type | Rear Derailleur (and other components) |
| Components | Derailleurs |
| Origin | Mainland China |
| High-concerned chemical | none |
7.2. Component Weights (Approximate)
- SL-M315-3X7S / ST-EF500 3X7S Shifter: ~350g
- RD-TY300-SGS Rear Derailleur: ~307g
- MF-TZ500-7S Cassette (28T/34T): ~420g
- VXM 6/7/8S Chain: ~300g
- FD-TY500 Front Derailleur: ~170g
- FC-TY301 Crankset: ~918g
- Bottom Bracket (BB): ~280g
7.3. Cassette and Crankset Details
- MF-TZ500-7S Cassette: Available in 14-28T or 14-34T configurations.
- FC-TY301 Crankset: 6/7/8-Speed compatible, 42-34-24T chainrings, 170mm crank arm length.
SHIMANO FC-TY301 Crankset with specifications.
SHIMANO MF-TZ500 14-34T 7-Speed Multiple Freewheel.
7.4. Package Dimensions and Weight
- Length: 35 cm
- Width: 23 cm
- Height: 19 cm
- Weight: 2.95 kg
8. User Tips
- Smooth Shifting: Always keep turning the crank during gear shifting for optimal performance and to prevent damage to the drivetrain.
- Cable Routing: Ensure outer casings are long enough to allow full handlebar movement without tension, and that the shifting lever does not contact the bike frame.
- Lubrication: Regularly grease inner cables and the sliding portions of outer casings with SIS SP41 grease (Y04180000) to maintain smooth operation.
- Braking in Wet Conditions: In wet weather, braking distance will be longer. Reduce your speed and apply brakes early and gently to avoid skidding and potential injury.
- Cassette Type: The TZ500 cassette is screw-on type (freewheel), not a freehub cassette. Ensure compatibility with your wheel hub.
9. Warranty and Support
For technical support, inquiries, or to obtain a hardcopy of the User's Manual if internet access is not available, please contact SHIMANO directly:
- SHIMANO NORTH AMERICA BICYCLE, INC.
One Holland, Irvine, California 92618, U.S.A.
Phone: +1-949-951-5003 - SHIMANO EUROPE B.V.
High Tech Campus 92, 5656 AG Eindhoven, The Netherlands
Phone: +31-402-612222
EU General Contact: contactshimano@shimano-eu.com - SHIMANO INC.
3-77 Oimatsu-cho, Sakai-ku, Sakai City, Osaka 590-8577, Japan
Please note: specifications are subject to change for improvement without notice. (English) © Sep. 2025 by SHIMANO INC. ITP
For a detailed user manual, please refer to the official PDF document: SHIMANO EZ-FIRE Plus ST-EF500/ST-EF510 Dealer's Manual (PDF)
10. Product Overview Video
Watch this video for a visual overview and unboxing of the SHIMANO Tourney 3x7 Speed Groupset components.
Video: Product overview and unboxing of the SHIMANO Tourney 3x7 Speed Groupset components.