Radtel RT-910B

Contents

Radtel RT-910B Dual Band UHF VHF Amateur Ham Radio Walkie Talkie Instruction Manual

Model: RT-910B / RT-910

1. Product Overview

The Radtel RT-910B is a dual-band UHF/VHF amateur ham radio walkie talkie featuring AM/FM receiver capabilities and 1024 channels. It supports one-click frequency copying, Bluetooth APP programming (for RT-910B Bluetooth version), noise reduction, channel grouping, and NOAA weather alerts. The device offers versatile charging options including Type-C and desktop charging.

Key Features:

  • Dual Band UHF/VHF TX/RX
  • AM/FM Receiver
  • 1024 Channels
  • One-Click Copy Frequency
  • Bluetooth APP Programming (RT-910B Bluetooth version only)
  • Noise Reduction
  • Channel Grouping
  • NOAA Weather Alert
  • Type-C & Desktop Charging
  • Hi/low power selectable
  • Repeater 1750Hz burst tone
  • Emergency alert function
  • VOX Handsfree Transmission
Two Radtel RT-910B radios, highlighting features like Bluetooth APP Programming, Noise Reduction, Channel Grouping, NOAA Weather Alert, Type-C & Desktop charging, and frequency ranges (6m:45-59Mhz TX/RX, U/V:45-540Mhz RX).

Figure 1: Radtel RT-910B Key Features and Frequency Ranges

2. Package Contents

Upon opening the package, ensure all items listed below are present and in good condition. If any items are missing or damaged, please contact your retailer.

Video 1: Unboxing and Basic Assembly of Radtel RT-910B

  • Radtel RT-910B Two-Way Radio Unit (x2)
  • Lithium Polymer Battery (x2)
  • Antenna (x2)
  • Belt Clip (x2)
  • USB Type-C Charging Cable (x2)
  • Power Adapter (x2)
  • User Manual (x1)
All components of the Radtel RT-910B package laid out, including two radios, two batteries, two antennas, two belt clips, two chargers, two Type-C cables, and a manual.

Figure 2: Radtel RT-910B Package Contents

3. Setup

3.1 Battery Installation

  1. Remove the battery from its packaging.
  2. Align the battery with the battery compartment on the back of the radio.
  3. Gently push the battery into place until it clicks securely.

3.2 Antenna Attachment

  1. Take the antenna from its packaging.
  2. Screw the antenna clockwise onto the connector at the top of the radio until it is finger-tight. Do not overtighten.

3.3 Belt Clip Attachment

  1. Align the belt clip with the screw holes on the back of the radio.
  2. Secure the belt clip using the provided screws.

3.4 Charging the Battery

Before first use, fully charge the battery. The radio supports both USB Type-C direct charging and desktop charger cradle charging.

Image illustrating USB Type-C Charging and Programming for the Radtel RT-910B, showing various charging methods (USB wall adapter, vehicle charging, power bank, PC charging).

Figure 3: USB Type-C Charging Options

Using the Desktop Charger:

  1. Connect the power adapter to the desktop charger cradle.
  2. Plug the power adapter into a suitable power outlet.
  3. Place the radio (with battery installed) into the charging cradle. Ensure the charging contacts align.
  4. The indicator light on the charger will show charging status (e.g., red for charging, green for fully charged).

Using USB Type-C Direct Charging:

  1. Connect the USB Type-C cable to the charging port on the side of the radio.
  2. Connect the other end of the USB Type-C cable to a USB wall adapter, vehicle charger, power bank, or PC USB port.
  3. The radio's screen or indicator light will show charging status.

4. Operating Instructions

4.1 Radio Buttons & Knobs Overview

ComponentDescription
AntennaTransmits and receives radio signals.
Power KnobTurns the radio ON/OFF and adjusts volume.
Indicator LightIndicates radio status (e.g., transmit, receive, charging).
ScreenDisplays frequency, channel, menu options, and status icons.
PTT ButtonPress to transmit.
PF2 ButtonShort press: Turn on FM RADIO. Long press: Switch High/Middle/Low power.
PF3 ButtonShort press: SEEK frequency from nearby radio. Long press: Open squelch.
Numeric KeypadFor frequency input, menu navigation, and shortcut functions.
Headphone JackFor connecting external audio accessories.
Microphone JackFor connecting external audio accessories.
SpeakerOutputs received audio.
Type-C Charger PortFor direct USB Type-C charging and programming.

4.2 Keypad Functions

Button/ActionFunction
VFO/MRSwitch channel and frequency mode.
OK (Menu/Confirm)Enter menu, confirm selection.
A/BSwitching A/B Band.
EXITExit/Back Button.
Long press 1 (SCAN)Enter scanning function.
Long press 2 (MEMCH)Store frequency into channel.
Long press 3 (STEP)Set frequency step.
Long press 4 (PWR)Select High, Middle, Low power.
Long press 5 (SQL)Adjust squelch levels.
Long press 6 (DUAL)Turn on/off dual standby.
Long press 7 (CTCSS)Set CTCSS sub tone.
Long press 8 (SHIFT)Set repeater shift direction.
Long press 9 (OFFSET)Set repeater offset frequency.
Long press 0 (FM)Turn on FM Radio broadcast.
Long press * (DTMF)DTMF tone edit.
Long press # (LOCK)Lock/Unlock keypad.

4.3 LCD Display Icons

IconDescription
AMAM Modulation Indicator: Current frequency is in AM modulation mode.
SCRScrambler Function: Indicates that the scrambler function is active.
VOXVOX (Voice-Operated Transmission): VOX function is enabled. Transmission starts when microphone sound pressure level reaches set threshold.
DMDual Standby: Dual-band standby function is active, allowing simultaneous monitoring of two frequency points.
MMonitor Function Enabled: Indicates that the monitor function is enabled.
♪Side Tone Enabled: Side tone function is active, producing a tone sound when transmitting DTMF.
🔒Keypad Lock: Appears when the keypad is locked. Long press # key to unlock.
RSSI barsSignal Strength: Indicates the strength of the received signal.
A/BA/B Band: Indicates whether the A band or B band is active.
VOLTransmit Audio Volume: Indicates the volume level of the transmitted audio.
Battery IconBattery Status: Displays remaining battery power. Flashes when nearly depleted. Green frame indicates super power-saving mode.
CTAnalog Sub-audio Tone Indicator: Current sub-audio tone is analog.
DCSDigital Sub-audio Tone Indicator: Current sub-audio tone is digital.
H/M/LHigh/Medium/Low Power Indicator: Current transmission power setting.
N/WNarrowband/Wideband Mode Indicator: Channel operating in narrowband/wideband mode.
+/-Frequency Mode (+/- Frequency Offset): Transmission frequency is reception frequency plus/minus offset.
RFrequency/Channel Mode Inverted Frequency: Reception and transmission frequencies are inverted.
SC(Encryption) Indicator: Encryption function is enabled.

4.4 Menu Function Operation

  1. Press the [OK] key to enter the menu.
  2. Use the UP/DOWN keys or the channel knob to select the desired menu option. Alternatively, input the keypad number for quick access.
  3. Press the [OK] key again to enter the selected menu.
  4. Use the UP/DOWN keys or the channel knob to adjust the setting, or input keypad numbers.
  5. Press the [OK] key to confirm the setting and return to the main menu.
  6. Press [EXIT] to exit the menu and return to normal operation mode.

Note: Frequency step, repeater shift direction, and frequency shift can only be set in frequency mode.

4.5 Basic Operations

Main Frequency Band Selection (A Band or B Band)

From the standby screen, press the A/B key to select the main frequency band. The larger display indicates the currently active band.

Zone Selection

Go to Menu 10 to select a zone number, or long-press the # key for quick access to change zones.

PTT Function

When operating on the A band, press the PTT key to transmit on the A band frequency. When operating on the B band, press the PTT key to transmit on the B band frequency.

AM Air Band Mode

Press VFO/MR to switch to frequency mode. Directly input the air band frequency within the range of 108 MHz to 136 MHz. The radio will automatically enter AM reception mode, and the channel status will display AM. This mode is primarily used to receive AM modulated signals.

Scanning Mode

Assign the scanning function to the side keys PF2/PF3, or long press button 1 to start frequency or channel scanning. You can choose one of the following modes from Menu 23:

  • Time Operation Mode (TO): When the radio detects a signal, it stops scanning and stays at the same frequency. After 5 seconds, it will resume scanning, even if the signal is still present.
  • Carrier Operation Mode (CO): The radio stops scanning and remains at the same frequency when it detects a signal, until the signal disappears. There is a 2-second delay before scanning resumes after the signal is lost.
  • Search Operation Mode (SE): Upon detecting a signal, the radio exits the scan and stays on this frequency.

Commercial FM Radio Broadcast Reception (Long Press Button 0)

  1. Long press the button 0 to turn on the FM RADIO; the screen will display the current frequency.
  2. Use the UP/DOWN keys or the channel knob to adjust the frequency. You can also input a frequency directly via the keypad. Press the OK button to switch the FM RADIO band between 65-76 MHz and 76-108 MHz.
  3. Simultaneously press the # key to enter automatic channel search mode. Long press the button 0 again to turn off the FM RADIO.

Frequency Sweep / Copy Frequency (Define PF2/PF3 buttons as SEARCH from Menu 24-26)

This function is used to seek the frequencies and sub-tones of nearby radios for immediate communication. After defining the side keys (PF buttons) as SEARCH, press the button until the LCD displays "SEARCH/SEEK…". Press the OK button to select the frequency band from UHF/VHF/200M/300M. After capturing a frequency, it will continue to seek sub-tone CTCSS/DCS. If no sub-tone is found, the LCD will display "NONE." At this point, you can press the [MENU] key to save the frequency to a specified channel, or press the UP or DOWN key to start the next frequency scan.

Two Radtel RT-910B radios demonstrating 'One-Click Copy Frequency' for quick search, match, and connect operations between intercomes.

Figure 4: One-Click Copy Frequency Feature

Weather Forecast NOAA Function (Define PF button as NOAA from Menu 24-26)

Press the designated side key to activate this function. The radio has 10 built-in fixed frequencies. You can press the UP/DOWN keys to select the frequency you want to listen to. Note: The NOAA weather forecast function is available only in countries and regions that support the NOAA channels.

DTMF Encode Sending

  • Fast Operation: Press and hold the PTT button while entering the number keys 0-9, MENU, UP, DOWN, EXIT, *, and #. The radio will transmit DTMF codes 0-9, A, B, C, D, *, and #. Release the button to stop sending codes.
  • Editing DTMF Code: In standby mode, long press the DTMF button to enter the DTMF code editing interface. You can enter codes 0-9, OK, UP, DOWN, Exit, *, and # via the keypad. Press PTT to send the DTMF code.

PTT-ID Function

Transmit identity codes or call codes via DTMF. There are 15 sets of call codes, configurable through "Programming Software → Edit → DTMF". Each signal or A/B band can independently select the call code group to be sent. Configure identity code parameters via "Programming Software → Edit → DTMF → Local ID Code". There are three transmission methods:

  • Send on Press: After pressing the PTT, the call code/identity code is sent first, followed by the voice signal.
  • Send on Release: After releasing the PTT, the call code/identity code is sent, then the transmission ends.
  • Send Both: The call code/identity code is sent both when the PTT is pressed and released.

VOX Function

Image demonstrating the VOX Function of the Radtel RT-910B, allowing hands-free operation suitable for driving or operating machinery.

Figure 5: VOX Handsfree Transmission

The VOX (Voice-Operated Transmission) function allows for hands-free operation. Transmission starts when the microphone's sound pressure level reaches the set threshold. This is suitable for situations like driving or operating machinery where holding the PTT button is inconvenient.

5. Maintenance

5.1 General Care

  • Do not expose the equipment or the battery charger directly to water or prolonged sunlight.
  • Avoid placing the radio near heat sources (e.g., radiators), or in areas with excessive dust, dirt, or fire hazards.
  • Do not store the transceiver inside a vehicle parked in direct sunlight.

5.2 Cleaning

To clean the equipment and/or the battery charger, ensure the device is OFF. Use an antistatic cloth (preferably) or a humid (not wet) cloth. Do not spray any liquid or product directly onto the transceiver, battery pack, or battery charger. Never use polish, detergents, alcohol, or solvents for cleaning. Avoid using a dry cloth for cleaning, as it could cause static shock.

5.3 Humidity Condensation

Humidity can condense on the transceiver when moved from a cold to a warm environment, potentially affecting its functionality. If condensation occurs, clean with a dry cloth and allow the device to dry completely before use.5.4 Battery Safety

There is a risk of explosion if the battery pack is replaced with an incompatible type. Use only genuine Radtel replacement batteries.

6. Troubleshooting

  • Malfunction (scent, smoke, etc.): If you notice any unusual scent, smoke, or other signs of malfunction from the transceiver or its battery charger, immediately turn it off or disconnect the battery charger from the AC wall outlet. Consult the Technical Service.
  • Interference with other electronics: If the transceiver causes interference with video recorders, DVDs, radio and television receivers, or any other electronic equipment, move the radio away from the affected apparatus.
  • Medical equipment: Do not use this transceiver in the vicinity of medical equipment as it can cause interference.
  • Restricted/Prohibited areas: Turn off and do not use the equipment in areas where its use is restricted or prohibited (e.g., coal gas areas, areas with explosion atmosphere, areas where it can interfere with the operation of other equipment, on board aircraft).

7. Specifications

General

ParameterValue
Store Channels960
AntennaDual Band U/V Antenna
Frequency Stability±2.5ppm
Dimensions13cm*6cm*5cm
Weight0.92 kg (package weight)
Operating Temperature-20 °C to +60 °C
Antenna Impedance50Ω
MaterialPlastic
Waterproof / Water-ResistantNo
DisplayYes

Frequency Range

  • 45-59Mhz FM TX/RX
  • 65-108Mhz FM RX
  • 108-136Mhz AM RX
  • 136-260Mhz TX/RX
  • 260-299Mhz RX
  • 300-520Mhz TX/RX

Receiver

ParameterValue
Sensitivity (FM)-121 dBm (12dB SINAD)
Sensitivity (WFM)-110 dBm (20dB SINAD)
Sensitivity (AM)-113 dBm (10dB S/N)
Audio Frequency≥0.5W
Audio Distortion≤5%

Transmitter

ParameterValue
Output Power3W-5W
Emission Current≤2A
Max Freq Deviation≤5Khz@25Khz/≤2.5Khz@12.5Khz
Modulation Distortion≤5%
Stray Power≤7.5uW
Battery Capacity1500mAh

8. User Tips

  • The RT-910B is noted for being slightly more sensitive than the RT-900B model, which can be beneficial for reception.
  • The included charging stand is very convenient for desktop use, providing a stable and easy way to charge your radio when not in use.

9. Warranty & Support

Manufacturer: XIAMEN RADTEL ELECTRONICS CO.,LTD
Address: 502, No.1, Jinyi Wuli, Huli, Xiamen, Fujian, China 361004
Email: support@radtel.com

9.1 Repairs and Modifications

Equipment repairs or internal adjustments should always be carried out by an Authorized Technical Service. Internal manipulation, alteration, or changes to the technical characteristics performed by unauthorized personnel will invalidate the warranty.

9.2 Regulatory Compliance

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This product meets the applicable Industry Canada technical specifications. Operation is subject to the following conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation.

For detailed information on RF energy exposure and how to control your exposure to assure compliance with established RF exposure limits, please refer to the official user manual (PDF) available at Radtel RT-910/RT-910B User Manual (PDF).

© 2024 Radtel. All rights reserved.


Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.