1. Product Overview
The JASIC NB-250 (N214II) is a versatile multi-process welding machine designed for MIG gas-protected welding, TIG welding, and Manual Metal Arc (MMA) welding. This manual provides essential information for the safe and efficient operation and maintenance of your welding equipment.

Figure 1: JASIC NB-250 (N214II) Welding Machine with included accessories.
2. Safety Information
Always prioritize safety when operating welding equipment. Failure to follow safety precautions can result in serious injury or death. Read and understand all safety warnings before use.
- Wear appropriate personal protective equipment (PPE), including welding helmet, gloves, and protective clothing.
- Ensure adequate ventilation to avoid inhaling welding fumes.
- Keep flammable materials away from the welding area.
- Ensure proper grounding of the welding machine.
- Do not touch live electrical parts.
3. Setup and Installation
3.1 Unboxing and Contents
Carefully unpack the welding machine and verify all components are present. The standard configuration includes:
- JASIC NB-250 (N214II) Welding Machine
- MIG welding gun (3 meters)
- Ground wire
- Gas meter pressure reducer
3.2 Power Connection
Connect the welding machine to a single-phase AC220V ± 15% power supply. Ensure the power outlet is properly grounded and can handle the rated input capacity of 7.7 kVA.
3.3 Welding Gun and Ground Clamp Connection
- Connect the MIG welding gun to the appropriate connector on the front panel.
- Attach the ground clamp to the workpiece, ensuring a clean and secure connection for optimal current flow.
3.4 Gas Connection (for MIG Welding)
For MIG gas-protected welding, connect the gas meter pressure reducer to your shielding gas cylinder. Then, connect the gas hose from the reducer to the gas inlet on the welding machine.
3.5 Wire Spool Installation (for MIG Welding)
Open the wire feeder compartment. Install the appropriate welding wire spool onto the spindle. Thread the wire through the feeder mechanism and into the MIG gun liner. Ensure the wire feed rollers are correctly sized for your wire and tensioned appropriately.

Figure 2: Wire feeder compartment open, illustrating wire spool installation.
4. Operating Instructions
4.1 Control Panel Overview
The front panel features a digital display and control knobs for selecting welding modes and adjusting parameters.

Figure 3: Front control panel of the welding machine.
4.2 Welding Mode Selection
Use the mode selector on the control panel to choose between MIG, TIG, or MMA welding processes.
4.3 Parameter Adjustment
- MIG Welding: Adjust welding current (50-200 A), welding voltage (13-26 V), and wire feed speed (2-24 m/min) according to the material thickness and wire type.
- Wipe Arc TIG Welding: Adjust welding current (50-200 A). This mode uses contact arc initiation.
- MMA Welding: Adjust welding current (50-160 A) suitable for the electrode type and size.
4.4 General Operation
Once parameters are set, ensure your workpiece is clean and properly clamped. Initiate the arc according to the selected welding process. Maintain a steady hand and consistent travel speed for quality welds.

Figure 4: Welding in progress using the JASIC NB-250 (N214II).
5. Maintenance
Regular maintenance ensures the longevity and optimal performance of your welding machine.
- Cleaning: Periodically clean the machine's exterior and ventilation openings to prevent dust and debris buildup. Use compressed air to clear internal components if necessary, ensuring the machine is unplugged.
- Cable Inspection: Regularly inspect all welding cables, including the welding gun, ground cable, and power cord, for any signs of damage, fraying, or loose connections. Replace damaged cables immediately.
- Wire Feeder Maintenance (MIG): Clean the wire feeder rollers and guide tubes to ensure smooth wire feeding. Check for wear on the rollers and replace if necessary.
- Consumables: Replace MIG gun nozzles, contact tips, and TIG torch consumables (collets, collet bodies, tungsten electrodes) as they wear out.
6. Troubleshooting
This section addresses common issues you might encounter during operation.
6.1 No Arc / Weak Arc
- Check Power: Ensure the machine is properly connected to the power supply and turned on.
- Ground Connection: Verify the ground clamp is securely attached to a clean, bare metal section of the workpiece.
- Cable Integrity: Inspect welding cables for damage or loose connections.
- Settings: Confirm welding current/voltage settings are appropriate for the material and process.
6.2 Wire Feeding Problems (MIG)
- Spool Installation: Ensure the wire spool is correctly installed and not tangled.
- Roller Tension: Adjust the wire feeder roller tension; too loose or too tight can cause issues.
- Contact Tip: Check if the contact tip is clogged or worn out. Replace if necessary.
- Liner: A dirty or kinked MIG gun liner can impede wire flow. Consider cleaning or replacing.
6.3 Poor Weld Quality
- Settings: Adjust welding current, voltage, and wire feed speed for optimal results.
- Shielding Gas (MIG): Verify gas flow rate and ensure the correct gas type is used. Check for leaks in the gas line.
- Workpiece Cleanliness: Ensure the welding area is free from rust, paint, oil, or other contaminants.
- Technique: Review welding technique, including travel speed, arc length, and torch angle.
7. Specifications
The following table details the technical specifications for the JASIC NB-250 (N214II) welding machine:

Figure 5: Detailed product specifications.
| Category | Parameter | Value |
|---|---|---|
| Model | Model Number | NB-250 (N214II) |
| Input | Input Voltage (V) | Single phase AC220 ± 15% |
| Rated Input Capacity (kVA) | 7.7 | |
| Power factor | 0.75 | |
| Output | Rated no-load voltage (V) | 56 |
| MIG | Welding Current (A) | 50 ~ 200 |
| Welding voltage (V) | 13 ~ 26 | |
| Wire feed speed range (m/min) | 2 ~ 24 | |
| Wipe Arc TIG | Welding Current (A) | 50 ~ 200 |
| Arc initiation mode | Contact arc initiation | |
| MMA | Welding Current (A) | 50 ~ 160 |
| Rated Load Sustainability | @40 °C | 30% |
| Efficiency | Efficiency | 81% |
| Protection Level | Protection Level | IP21S |
| Insulation Level | Insulation Level | H |
| Shape size | L*W*H(mm) | 597*298*503 |
| Weight | (kg) | 22.6 |
| Package size | L*W*H(mm) | 690*390*595 |
| Gross weight | (kg) | 31.1 |
8. User Tips
- Always perform test welds on scrap material to fine-tune your settings before working on your main project.
- For MIG welding, ensure your shielding gas flow rate is consistent to prevent porosity in your welds.
- When switching between welding processes, double-check all connections and settings to match the chosen mode.
- Keep your welding area clean and organized to minimize hazards and improve workflow.
9. Warranty and Support
The JASIC NB-250 (N214II) welding machine comes with a 1-year warranty from the date of purchase. This warranty covers manufacturing defects under normal use. For warranty claims or technical support, please contact your authorized dealer or the manufacturer's customer service.
For any questions regarding the product or assistance, please reach out to the support team.