9IMOD F722 Flight Stack

Contents

9IMOD F722 Flight Stack Instruction Manual

Model: F722 Flight Stack

1. Introduction

The 9IMOD F722 Flight Stack is a high-performance integrated solution for FPV racing drones, combining an F722 Flight Controller with either a 55A or 60A Electronic Speed Controller (ESC). Designed for optimal performance and ease of use, it supports BlueJay firmware and bidirectional DSHOT protocols. The flight controller features an STM32F722RET6 master chip, ICM42688 gyroscope, and an onboard OSD chip and barometer, ensuring stable operation even in complex flight environments. Its large solder pads are strategically placed away from components to facilitate easier soldering for all users.

2. Features

  • Open-source Betaflight Flight Controller for extensive customization.
  • High Configuration: Equipped with STM32F722RET6 master chip, ICM42688 gyroscope, BMP280 barometer, and AT7456E OSD chip.
  • Optimized PCB layout and routing for enhanced performance and reliability.
  • Built-in OSD module for convenient, one-step parameterization.
  • Standard sockets and pads are all led out, providing versatile connection options for various user needs.
  • 4-in-1 ESC utilizes high-performance MOS for excellent current resistance, long durability, and stability.
  • High-performance processor supports DSHOT600 protocol, ensuring smooth and powerful acceleration.
  • Supports BlueJay firmware and bidirectional DSHOT.

3. Specifications

F722 Flight Control Parameters

ParameterValue
Master ChipSTM32F722RET6
GyroscopeICM42688
Battery Input3-8S
USB PortType-C
BarometerBMP280
OSD ChipAT7456E
BluetoothNot Supported
RSSI SupportYes (marked as RSSI)
Supported FC FirmwareBetaflight
Firmware NameDAKEFPVF722
iNav SupportYes
Ardupilot SupportNo
DJI O4 ConnectionYes
GPS Module SupportRequires u-blox protocol support
Installation Hole Position30.5x30.5mm/M4
Dimensions36mm x 36mm x 8mm
Weight (Bare Board)8g

55A ESC Parameters

ParameterValue
MCUEFM8BB21F16G-C-QFN20R
Continuous Current55A x 4
Transient Current60A (10S)
ProgramBlueJay
MOS3109
TVS Protection DiodeYes
Electrolytic Capacitor1000uF Low ESR
Motor ProtocolDshot300/600
Battery Input3-6S Lipo
AmmeterYes
Power OutputVBAT
Installation Hole Position30.5x30.5mm/M4
DimensionsLength 43mm x Width 37mm x Height 7mm
Weight (Bare Board)12g

60A ESC Parameters

ParameterValue
MCUEFM8BB21F16G-C-QFN20R
Continuous Current60A x 4
Transient Current65A (10S)
ProgramBlueJay
MOS5C430
TVS Protection DiodeYes
Electrolytic Capacitor1000uF Low ESR
Motor ProtocolDshot300/600
Battery Input3-8S Lipo
AmmeterYes
Power OutputVBAT
Installation Hole Position30.5x30.5mm/M4
DimensionsLength 43mm x Width 37mm x Height 7mm
Weight (Bare Board)12g

4. Package Contents

The package typically includes the following components, depending on the selected variant (55A or 60A ESC):

  • F722 Flight Controller x 1
  • 55A or 60A ESC x 1
  • Package Box x 1
  • TS100 GPS Connect Cable x 1
  • ESC Connect Cable(s) x 1 or 2 (depending on ESC variant)
  • R8SM Receiver Connect Cable x 1
  • Analog Video Transmission Connect Cable x 1
  • Camera Connect Cable x 1
  • ELRS Receiver Connect Cable x 1
  • Power cable + XT60 x 1
  • Low ESR capacitor x 1
  • Silicone vibration absorber x 8
  • Screw x 4
  • Hex nut x 4
Package contents for F722 Flight Control + 55A ESC
Figure 1: Package contents for F722 Flight Control + 55A ESC.
Package contents for F722 Flight Control + 60A ESC
Figure 2: Package contents for F722 Flight Control + 60A ESC.

5. Setup and Wiring

Careful wiring is crucial for the proper functioning of your FPV drone. Refer to the diagrams below for connecting the F722 Flight Controller and ESC to other components such as motors, receivers, cameras, VTX, GPS, and LEDs.

Detailed wiring diagram for F722 Flight Stack, showing connections for receiver, camera, VTX, GPS, and LED
Figure 3: Detailed wiring diagram for the F722 Flight Stack, illustrating connections for various peripherals.
Wiring diagram for F722 Flight Stack showing motor connections and other peripherals
Figure 4: Comprehensive wiring diagram for the F722 Flight Stack, including motor connections and various FPV components.

Key Wiring Considerations:

  • Power Input: Connect your Lipo battery (3-8S) to the designated BAT+ and BAT- pads on the ESC.
  • Motors: Connect each motor to the corresponding motor pads (M1-M4) on the ESC. Ensure correct motor rotation direction, which can be configured in Betaflight/BlueJay.
  • Receiver: Connect your receiver (e.g., Crossfire Nano Rx, R8SM, ELRS) to the appropriate UART pads (e.g., RX3 for Crossfire/ELRS).
  • Camera: Connect your FPV camera to the CAM pads (Video In, GND, 5V).
  • Video Transmitter (VTX): Connect your VTX to the VTX pads (Video Out, GND, 5V/12V). For digital video transmission (e.g., DJI O4), ensure proper connection to the dedicated 6p digital image transmission interface. If using SBUS control protocol for digital image transmission, short the solder pad jumper as indicated in the diagram.
  • GPS Module: If using a GPS module, ensure it supports the u-blox protocol and connect it to the designated UART for GPS.
  • LEDs/Buzzer: Connect LEDs and buzzers to their respective pads (LED, BZ+ / BZ-).
  • Solder Pads: Utilize the large solder pads for secure connections. Ensure no solder bridges are created.

6. Operating Instructions

The 9IMOD F722 Flight Stack runs on Betaflight firmware. Initial setup and configuration are performed using the Betaflight Configurator software on a computer.

Initial Setup Steps:

  1. Connect to PC: Connect the Flight Controller to your computer using a Type-C USB cable.
  2. Install Drivers: Ensure all necessary drivers (e.g., STM32 Virtual COM Port Driver, Zadig for DFU mode) are installed.
  3. Betaflight Configurator: Open the Betaflight Configurator software.
  4. Firmware Flash: If necessary, flash the DAKEFPVF722 firmware. Always back up your configuration before flashing.
  5. Configuration: Configure your flight controller settings, including accelerometer calibration, PID tuning, receiver setup, motor output, OSD elements, and flight modes.
  6. ESC Configuration: The ESCs support BlueJay firmware. Use the appropriate configurator (e.g., BlueJay Configurator) to update firmware, set motor direction, and configure other ESC parameters.
  7. Testing: After configuration, perform bench testing to verify motor direction, receiver input, and sensor functionality before attempting flight.

The built-in OSD module allows for on-screen display of critical flight data and in-field parameter adjustments using your FPV goggles or monitor.

7. Troubleshooting

If you encounter issues with your F722 Flight Stack, consider the following common troubleshooting steps:

  • No Power/Boot Issues: Double-check all power connections. Ensure the battery is charged and connected correctly. Inspect for any short circuits.
  • Motors Not Spinning/Incorrect Direction: Verify motor wiring to the ESC. Check motor protocol settings (Dshot300/600) in Betaflight. Use the BlueJay Configurator to ensure correct motor direction and ESC firmware.
  • No Receiver Input: Confirm receiver is correctly wired to the FC's UART. Check UART configuration in Betaflight. Ensure receiver protocol (e.g., SBUS, CRSF) is correctly selected in Betaflight and on the receiver itself.
  • OSD Not Displaying: Check OSD settings in Betaflight Configurator. Ensure camera and VTX are correctly connected and powered.
  • Unstable Flight: Review PID settings. Ensure the flight controller is mounted securely and isolated from vibrations. Check for bent propellers or damaged motors.
  • Connection to PC Issues: Ensure correct USB drivers are installed. Try a different USB cable or port. If stuck in DFU mode, use Zadig to install the correct driver.

8. User Tips

While specific user reviews or Q&A were not provided, general tips for FPV flight controllers and ESCs include:

  • Always perform a dry run (without propellers) after any configuration changes to ensure motors spin correctly and in the right direction.
  • Regularly check for firmware updates for both Betaflight and BlueJay to benefit from performance improvements and bug fixes.
  • Use heat shrink tubing or electrical tape to insulate exposed solder joints and prevent short circuits.
  • Consider using a smoke stopper during initial power-up to prevent damage in case of a short circuit.

9. Safety Information

⚠ WARNING: This product can expose you to chemicals including phthalates (DEHP), which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.

Always handle electronic components with care. Ensure proper ventilation when soldering. Disconnect power before making any wiring changes. FPV drones can be dangerous; always operate in a safe environment and follow local regulations.

10. Warranty and Support

For technical support, firmware updates, and detailed documentation, please refer to the official Betaflight and BlueJay resources online. For product-specific inquiries, contact your retailer or the manufacturer.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.