1. Introduction
The CUAV C-RID Drone Remote ID Broadcast Module is a compact and lightweight device designed to enable drones to comply with remote identification regulations in various countries and regions, including China, the European Union, and the United States. It broadcasts essential drone identification and location data, enhancing airspace safety and regulatory compliance. This module is built with a high-performance dual-core processor and supports both DroneCAN bus and UART serial communication, making it compatible with popular flight control systems like ArduPilot and PX4.
2. Product Overview
The C-RID module is engineered for reliability and ease of integration. Its robust aviation aluminum shell protects the internal components, while its small size and dedicated M2.5 fixing holes allow for flexible installation on various drone platforms.
2.1 Key Features
- Regulatory Compliance: Designed based on China, EU, and ASTM drone identification code standards.
- High Performance: Equipped with an Xtensa® 32-bit LX7 dual-core processor (240 MHz, 512 KB SRAM, 384 KB ROM).
- Long-Range Broadcast: Utilizes 2.4 GHz Wi-Fi (IEEE 802.11b/g/n) and Bluetooth® 5 (LE) for broadcasting over 300 meters.
- Versatile Communication: Supports DroneCAN bus and UART serial communication (MAVLink protocol).
- Compact & Lightweight: Weighs only 5.5g with dimensions of 38x38x10mm (including fixing holes).
- Firmware: ArduRemoteID (supports OTA online upgrade).
- Compatibility: Fully compatible with ArduPilot and PX4 flight controllers.
- Security: Enhances tamper resistance and secure broadcasting of drone identification codes when used with CUAV controllers.
2.2 Components
The standard package includes the following items:

- 1 x C-RID Module
- 1 x CAN Cable (35 cm)
- 1 x External 2.4G Antenna (including antenna: 75 cm)
2.3 Visual Overview




3. Specifications

| Attribute | Value |
|---|---|
| Processor | Xtensa® 32-bit LX7 dual-core processor |
| Communication Frequency | 2.4 GHz |
| Range | >300m |
| Firmware | ArduRemoteID (Support OTA Online Upgrade) |
| Shell Material | Aviation Aluminum |
| Size (Main) | 24 × 38 × 10mm |
| Size (Including Fixing Hole) | 38 × 38 × 10mm |
| Protocol | DroneCAN/UART (MAVLink) |
| Communication Mode | Wi-Fi or Bluetooth Broadcast |
| Transmit Power | 20dBm |
| Ports | 1 x CAN (4-pin GH1.25), 1 x UART (4-pin GH1.25), 1 x ANT (MMCX) |
| Operating Voltage | 4.7~5.2V |
| Weight | 5.5g |
| Main LED Status | Off: Not connected or not working Constant Red: Configuration is not completed (disarming conditions are not met) Constant Green: Configuration is successful, unlockable |
| Certification | CE, FCC |

4. Setup
4.1 Physical Installation
- Mounting: The C-RID module features dedicated M2.5 fixing holes for secure attachment. It can be flexibly fixed using screws or 3M adhesive, depending on your drone's structure and preference. Ensure the module is mounted in a location that does not obstruct its antenna or interfere with other drone components.
- Antenna Connection: Connect the provided external 2.4G antenna to the MMCX antenna port on the C-RID module. Ensure a firm connection for optimal broadcast range.
4.2 Electrical Connection
The C-RID module supports both DroneCAN and UART serial communication for integration with your flight controller.

- DroneCAN Connection: Use the provided CAN cable to connect the C-RID module's CAN port to a DroneCAN-compatible port on your flight controller. The DroneCAN bus offers strong anti-interference ability and high transmission rates.
- UART Connection: Alternatively, use the UART port for serial communication with your flight controller. This is useful for devices that do not yet support the DroneCAN protocol.
- Power Supply: The module operates on 4.7~5.2V. Ensure your flight controller or power distribution board provides stable power within this range to the connected port.
4.3 Initial Configuration
After physical and electrical connections, the C-RID module requires configuration to broadcast the correct identification data. Refer to the ArduRemoteID firmware documentation for detailed steps on configuring your specific drone and operator information. The firmware supports OTA (Over-The-Air) online upgrades, ensuring you can keep your module up-to-date with the latest features and regulatory requirements.
5. Operating Instructions
Once installed and configured, the C-RID module operates automatically to broadcast your drone's Remote ID information during flight.
5.1 Broadcast Operation
- The module continuously broadcasts drone identification codes via 2.4 GHz Wi-Fi and Bluetooth 5 (LE).
- The broadcast range is typically over 300 meters, providing wide coverage for compliance.

5.2 LED Status Indicator
Monitor the main LED on the C-RID module for its operational status:
- Off: The module is not connected or not working. Check power and connections.
- Constant Red: Configuration is not completed, or disarming conditions are not met. Review your setup and flight controller parameters.
- Constant Green: Configuration is successful, and the drone is unlockable (ready for flight).
5.3 Data Monitoring with LGC
The C-RID module can cooperate with LGC (LecentGroundControl) software to set and analyze broadcast data. This allows for real-time monitoring of dynamic drone information, including position, in the region.


6. Maintenance
- Keep Clean: Regularly inspect the module for dust or debris. Use a soft, dry cloth to clean the exterior. Avoid using harsh chemicals or solvents.
- Inspect Connections: Periodically check all cable connections (CAN, UART, Antenna) to ensure they are secure and free from damage.
- Firmware Updates: Keep the ArduRemoteID firmware updated to ensure compliance with the latest regulations and to benefit from performance improvements. Updates can typically be performed Over-The-Air (OTA).
- Environmental Conditions: Operate and store the module within recommended environmental conditions to prevent damage. Avoid extreme temperatures, humidity, and direct exposure to water.
7. Troubleshooting
7.1 No LED Indication / Module Not Powering On
- Check Power: Verify that the module is receiving power (4.7~5.2V) from the flight controller or power source.
- Cable Connection: Ensure the power cable is securely connected to both the C-RID module and the flight controller.
- Flight Controller Status: Confirm that the flight controller itself is powered on and functioning correctly.
7.2 LED is Constant Red (Configuration Issue)
- Initial Configuration: If this is the first use, ensure you have completed the initial configuration steps as per the ArduRemoteID firmware documentation.
- Disarming Conditions: The red LED indicates that the drone's disarming conditions are not met. This could be due to incorrect flight controller settings, GPS lock issues, or other pre-flight checks. Consult your flight controller's manual and the ArduRemoteID documentation.
- Firmware Integrity: If the issue persists, consider re-flashing or updating the firmware.
7.3 Broadcast Not Detected
- Antenna Connection: Ensure the external 2.4G antenna is properly connected and not obstructed.
- Range: Verify you are within the broadcast range (>300m) when attempting to detect the signal.
- Receiver Device: Ensure your receiving device (e.g., smartphone with LGC app) is compatible and correctly configured to detect Remote ID broadcasts.
- Firmware Settings: Double-check the Remote ID settings within the ArduRemoteID firmware to ensure broadcasting is enabled and configured correctly.
8. User Tips
- Optimal Placement: For best broadcast performance, mount the C-RID module in a location on your drone that has a clear line of sight to the sky and is away from major metallic or carbon fiber structures that could interfere with the 2.4 GHz signal.
- Regular Firmware Checks: Periodically check the CUAV official website or ArduRemoteID project page for new firmware releases. Keeping your firmware updated ensures you have the latest features and compliance with evolving regulations.
- Test Before Flight: Always perform a ground test after installation and configuration to verify that the C-RID module is broadcasting correctly and the LED indicator is green before commencing flight operations.
- LGC Software: Utilize the LecentGroundControl (LGC) software for advanced monitoring and analysis of broadcast data, which can be crucial for regulatory reporting or flight analysis.
9. Warranty & Support
For warranty information, technical support, and further assistance, please refer to the official CUAV website or contact their customer service. Keep your purchase receipt as proof of purchase for any warranty claims.