Audi 4B0601170

Contents

Audi Wheel Center Cap Instruction Manual

Model: 4B0601170

1. Introduction

This manual provides instructions for the installation, maintenance, and specifications of the 60mm Audi Wheel Center Caps. These caps are designed to fit various Audi models, enhancing the aesthetic appeal of your vehicle's wheels.

2. Product Specifications

FeatureDetail
BrandAudi
Part Number (PN)4B0601170 (Interchangeable)
Outer Diameter60mm
Inner Diameter60mm
Quantity4 pieces per set
Available ColorsBlack, Grey
OriginMainland China
CompatibilityAll wheel rims with 60mm center caps for Audi A3, A4 (B6, B8, B7, B5), A6 (C5, C6), A5, A1, A8, S3, S4, S5, S6, S7.

3. Package Contents

Your package should contain the following items:

  • 4 x Audi Wheel Center Caps (60mm)
Four black Audi wheel center caps, front and back view

Figure 1: Example of 4 black wheel center caps (front and back views).

Four grey Audi wheel center caps, front and back view

Figure 2: Example of 4 grey wheel center caps (front and back views).

4. Installation Guide

Installation of the wheel center caps is straightforward. Ensure your vehicle is parked on a level surface and the engine is off before proceeding.

  1. Prepare the Wheel: If replacing existing caps, carefully remove the old center caps. This can often be done by prying them out gently from the edge using a plastic trim removal tool to avoid scratching the wheel. If installing on new wheels, ensure the center bore is clean and free of debris.
  2. Align the Cap: Take one new wheel center cap. Observe the retaining clips and the metal ring on the back of the cap.
  3. Close-up of the back of two stacked wheel center caps, showing the retaining clips and metal ring

    Figure 3: Rear view of the wheel center cap, highlighting the retaining clips and metal ring.

  4. Insert the Cap: Carefully align the new center cap with the center bore of the wheel.
  5. Secure the Cap: Apply even pressure to the center of the cap until you hear or feel it snap securely into place. Ensure all retaining clips are fully engaged. Do not force the cap, as this may damage the clips or the wheel.
  6. Verify Installation: Gently tug on the cap to ensure it is firmly seated and does not wobble.
  7. Repeat: Repeat the process for the remaining wheel center caps.

Note: The part number 4B0601170 is located on the back of the cap for reference.

Close-up of the back of a wheel center cap with part number 4B0601170 visible

Figure 4: Part number 4B0601170 visible on the rear of the cap.

5. Operation

These wheel center caps are static decorative and protective components. No operational steps are required after proper installation.

6. Maintenance and Care

  • Cleaning: Clean the wheel center caps regularly with mild car soap and water. Avoid harsh chemicals or abrasive cleaners, as these can damage the finish.
  • Inspection: Periodically check the caps to ensure they are still securely seated in the wheel. If a cap feels loose, gently press it back into place.
  • Protection: While durable, avoid direct impact or excessive force on the caps to prevent damage.

7. Troubleshooting

  • Cap does not fit:
    • Verify the diameter of your wheel's center bore. These caps are 60mm.
    • Ensure you are aligning the cap correctly with the wheel's center bore.
    • Check for any obstructions in the wheel's center bore.
  • Cap feels loose or falls off:
    • Ensure all retaining clips on the back of the cap are intact and not bent or broken.
    • Re-install the cap, applying firm, even pressure until it clicks into place.
    • If the cap continues to be loose, the retaining clips may be damaged, or the cap may not be compatible with your specific wheel.

8. User Tips

  • When removing old caps, a small flat-head screwdriver wrapped in tape (to prevent scratches) can be used to gently pry them out from the edge.
  • For a secure fit, ensure the wheel's center bore is clean before installation.
  • Consider purchasing a spare set if you frequently drive on rough roads or in areas where caps might be dislodged.

9. Warranty and Support

For any issues or questions regarding your Audi Wheel Center Caps, please contact the seller or manufacturer for support. Specific warranty details may vary by seller.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.