Douk Audio P10

Contents

Douk Audio P10 Desktop Class A Headphone Amplifier

User Manual

Introduction

The Douk Audio P10 is a compact yet powerful Class A headphone amplifier designed to enhance your audio experience. It features a built-in innovative voltage boost circuit, delivering pure and dynamic sound. With versatile input and output options, including dual headphone jacks, it is compatible with a wide range of audio sources and headphones, from sensitive in-ear monitors (IEMs) to demanding over-ear models. The P10 also offers the flexibility of swappable op-amps for personalized sound tuning.

Douk Audio P10 Headphone Amplifier front view
Figure 1: Front view of the Douk Audio P10 Headphone Amplifier, showcasing its compact design and dual headphone outputs.

Setup Instructions

  1. Power Connection: Connect the supplied DC 5V/2A power adapter to the 'DC 5V IN' port on the rear panel of the P10. Ensure the power adapter provides at least 1A current for optimal performance.
  2. Audio Input: Connect your audio source (e.g., DAC, PC, phone, CD player) to either the Stereo RCA inputs (R/L) or the 3.5mm AUX input on the rear panel.
  3. Headphone Output: Connect your headphones to either the 3.5mm or 6.35mm headphone jack on the front panel. Both outputs can be used simultaneously. The 3.5mm output can also function as a preamp output for connecting to external amplifiers or active speakers.
  4. Power On: Turn the 'VOL' knob clockwise to power on the device. The knob also controls the volume.
Douk Audio P10 Input and Output Diagram
Figure 2: Diagram illustrating the front and rear panels of the P10, showing the DC 5V input, RCA and AUX inputs, and 6.35mm/3.5mm headphone outputs. Compatible devices like tablets, phones, CD players, TVs, laptops, and MP3 players are shown as input sources, while headphones, amplifiers, and active speakers are shown as output devices.

Operating Instructions

  1. Volume Control: The 'VOL' knob on the front panel serves as both the power switch and volume control. Rotate clockwise to increase volume and counter-clockwise to decrease.
  2. Headphone Connection: Plug your headphones into either the 3.5mm or 6.35mm jack. The P10 can effortlessly drive headphones with impedance ranging from 24Ω to 600Ω.
  3. Op-Amp Swapping (Advanced): The P10 features dual NE5532 op-amps in pluggable sockets, allowing for customization. To swap op-amps, carefully open the device and replace the existing op-amps with compatible alternatives such as LME49720NA-DIP-8 or any other dual op-amp in an 8-pin package with an output current exceeding 50mA. This allows for fine-tuning the sound signature.
Douk Audio P10 Op-Amp Swapping
Figure 3: Image demonstrating the process of carefully swapping op-amps on the P10's circuit board using tweezers, highlighting the customizable nature of the amplifier.
Douk Audio P10 driving 24-600 Ohm headphones
Figure 4: The P10 amplifier connected to a pair of headphones, illustrating its capability to drive headphones with impedance from 24Ω to 600Ω.

Maintenance

  • Cleaning: Use a soft, dry cloth to clean the exterior of the amplifier. Avoid using liquid cleaners or solvents.
  • Environment: Keep the device in a dry, well-ventilated area, away from direct sunlight, heat sources, and excessive moisture.
  • Storage: When not in use for extended periods, disconnect the power adapter and store the amplifier in a safe place.

Troubleshooting

  • No Power: Ensure the DC 5V/2A power adapter is securely connected and functioning. Verify that the power supply provides at least 1A current.
  • No Sound: Check all audio connections (input and output). Ensure the volume knob is turned up. Confirm that your audio source is playing.
  • Mixed Audio Signals: Avoid connecting both the RCA and 3.5mm AUX inputs simultaneously, as this will mix the audio signals. Use only one input at a time.
  • Distorted Sound: Check the impedance of your headphones to ensure they are within the 24-600Ω range. Ensure the input audio source is not overdriving the amplifier.
  • Intermittent Sound: Check for loose connections or damaged cables.

Specifications

ParameterValue
BrandDouk Audio (Nobsound)
ModelP10
Audio InputStereo RCA / 3.5mm AUX
Audio Output3.5mm / 6.35mm Headphone Jack
Output Power≥1100mW (32Ω)
Matched Headphone Impedance24-600Ω
Frequency Response20-30KHz
SNR≥ 110dB
Output Voltage Swing30V
Input VoltageDC 5V/≥ 1A (5.5*2.5mm)
Dimensions (W*D*H)78*82*32mm / 3.07*3.23*1.26in
Net Weight210g / 0.46lb
Package Weight400g / 0.88lb
Douk Audio P10 dimensions and packing list
Figure 5: Visual representation of the P10 amplifier's dimensions and the contents of the packing list, including the P10 unit, DC 5V power adapter, and user manual.

User Tips

  • Op-Amp Experimentation: For audiophiles and DIY enthusiasts, the swappable op-amp design offers a great opportunity to experiment with different sound characteristics. Ensure any replacement op-amps are dual op-amps in an 8-pin package with an output current exceeding 50mA.
  • High-Impedance Headphone Compatibility: The P10 is well-suited for driving high-impedance headphones such as HD580, HD600, HD650, K701, K702, Q701, DT880, T70, T90, SR225, SR325, and RS1e, providing ample power and clarity.
  • Preamp Functionality: The 3.5mm headphone output can double as a preamp output, allowing you to connect the P10 to a larger power amplifier or active speakers, expanding its versatility in your audio setup.

Warranty and Support

For warranty information, technical support, or service inquiries, please refer to the official Douk Audio website or contact your retailer. Keep your purchase receipt as proof of purchase.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.