Cecotec Conga Rockstar Wet & Dry Steel Pro Tool 1600W Vacuum Cleaner

1. Introduction

Thank you for choosing the Cecotec Conga Rockstar Wet & Dry Steel Pro Tool vacuum cleaner. This powerful 1600W appliance is designed for efficient cleaning of both solid debris and liquids, featuring a durable 30-liter metal tank and a high-efficiency HEPA filter. This manual provides essential information for safe operation, assembly, maintenance, and troubleshooting to ensure optimal performance and longevity of your vacuum cleaner.

Figure 1: Conga Rockstar Wet & Dry Steel Pro Tool with included accessories.

2. Safety Instructions

Please read all safety warnings and instructions before using this appliance. Failure to follow the warnings and instructions may result in electric shock, fire, and/or serious injury.

• Always ensure the power supply matches the voltage specified on the rating label.
• Do not use the vacuum cleaner in wet conditions unless specifically designed for wet vacuuming, and always ensure proper filters are installed.
• Never vacuum flammable or combustible liquids, hot ashes, or sharp objects.
• Keep hair, loose clothing, fingers, and all parts of the body away from openings and moving parts.
• Unplug from the outlet when not in use and before servicing.
• Do not allow to be used as a toy. Close attention is necessary when used by or near children.
• Do not use with a damaged cord or plug. If the appliance is not working as it should, has been dropped, damaged, left outdoors, or dropped into water, return it to a service center.
• Do not pull or carry by cord, use cord as a handle, close a door on cord, or pull cord around sharp edges or corners. Keep cord away from heated surfaces.

3. Package Contents

Carefully unpack the box and ensure all items are present and in good condition. If any items are missing or damaged, contact your retailer.

• 1 x Conga Rockstar Wet & Dry Steel Pro Tool Vacuum Cleaner
• 1 x Corner Accessory
• 1 x Floor Brush
• 1 x Drill Dust Collector Accessory
• 1 x Extendable Tube (Telescopic Wand)
• 1 x Flexible Tube (Hose)
• 1 x User Manual

4. Assembly and Setup

Follow these steps to assemble your vacuum cleaner before first use.

1. Attach the Wheels: Turn the main unit upside down. Insert the four caster wheels into the designated slots on the base until they click into place.
2. Connect the Flexible Tube (Hose): Locate the suction inlet on the front of the vacuum cleaner's tank. Insert the flexible tube's connector firmly into this inlet until it is securely locked.
3. Assemble the Extendable Tube and Accessories:
   • Attach one end of the extendable tube to the handle of the flexible tube.
   • Select the desired accessory (e.g., Floor Brush, Corner Accessory) and attach it to the other end of the extendable tube.
4. Filter Installation: Ensure the HEPA filter and water filter are correctly installed inside the tank. For dry vacuuming, the HEPA filter must be in place. For wet vacuuming, the water filter should be used, and the HEPA filter may need to be removed or replaced with a foam filter (if provided and specified for wet use). Refer to the Maintenance section for detailed filter information.

Figure 2: Fully assembled vacuum cleaner, ready for operation.

5. Operation

Your Conga Rockstar vacuum cleaner offers both wet and dry vacuuming, as well as a blowing function.

5.1. Powering On/Off

The vacuum cleaner features a main power switch located on the top control panel.

1. Plug the power cord into a suitable electrical outlet.
2. Press the power switch (refer to Figure 3) to turn the unit ON.
3. Press the power switch again to turn the unit OFF.

Figure 3: Top control panel with power switch and tool socket.

5.2. Dry Vacuuming

For dry vacuuming, ensure the HEPA filter is correctly installed.

1. Attach the desired dry cleaning accessory (e.g., Floor Brush for large areas, Corner Accessory for crevices).
2. Turn on the vacuum cleaner.
3. Move the accessory over the surface to be cleaned, collecting dust and debris.

Figure 4: Dry vacuuming on a patio surface.

5.3. Wet Vacuuming

For wet vacuuming, ensure the appropriate wet filter (e.g., foam filter) is installed and the HEPA filter is removed to prevent damage. Do not overfill the tank.

1. Remove the HEPA filter and install the wet filter (if applicable).
2. Attach the appropriate wet cleaning accessory.
3. Turn on the vacuum cleaner.
4. Move the accessory over the liquid spill to suction it into the tank.
5. Monitor the tank level to avoid overfilling. The vacuum has a float mechanism that will stop suction when the tank is full.

5.4. Blowing Function (Blowing System)

The vacuum cleaner can also be used as a blower to clear debris from surfaces or to collect dust when using power tools.

1. Disconnect the flexible tube from the suction inlet.
2. Locate the blowing outlet (usually on the rear or side of the motor head).
3. Attach the flexible tube to the blowing outlet.
4. Turn on the vacuum cleaner. Air will now be expelled from the hose.
5. Use the drill dust collector accessory by connecting it to the hose and positioning it near the drilling area to capture dust.

Figure 5: Using the blower function with a drill dust collector accessory.

6. Maintenance

Regular maintenance ensures the efficiency and longevity of your vacuum cleaner.

6.1. Emptying the Tank

Empty the tank after each use, especially after wet vacuuming.

1. Unplug the vacuum cleaner from the power outlet.
2. Release the latches securing the motor head to the tank.
3. Carefully lift the motor head off the tank.
4. Pour out any liquids or dispose of solid debris from the tank.
5. Clean the inside of the tank with water and mild detergent if necessary, then dry thoroughly.

6.2. Filter Cleaning and Replacement

The Conga Rockstar features a double filtering system with a HEPA filter and a water filter.

• HEPA Filter: For dry vacuuming, the HEPA filter retains fine dust and allergens. It should be cleaned regularly by tapping it gently to remove dust or by rinsing it under cold water. Ensure it is completely dry before re-installing. Replace the HEPA filter every 6-12 months, or sooner if suction power decreases significantly.
• Water Filter: For wet vacuuming, the water in the tank acts as a primary filter. The water should be emptied and replaced after each wet use. The foam filter (if present for wet use) should be rinsed and dried.

Figure 6: Cleaning the filter and emptying the tank.

6.3. Accessory Cleaning

Clean all accessories (hoses, tubes, brushes) regularly to prevent blockages and maintain hygiene. Rinse them with water and mild soap, then allow them to air dry completely.

7. Troubleshooting

If you encounter issues with your vacuum cleaner, refer to the following table for common problems and solutions.

8. Specifications

9. User Tips

While no specific user reviews or Q&A were available for this manual, here are some general tips for maximizing your vacuum cleaner's performance:

• For optimal suction, always ensure the tank is not overfilled and filters are clean.
• When switching between wet and dry vacuuming, always change or clean the filters accordingly to prevent damage and maintain efficiency.
• Utilize the accessory holder system for convenient storage and easy access to attachments during cleaning tasks.
• The blowing function is excellent for clearing leaves from patios or sawdust from workshops.

10. Warranty and Support

For warranty information, technical support, or service inquiries, please refer to the warranty card included with your product or contact Cecotec customer service directly. Keep your proof of purchase for any warranty claims.