1. Introduction
This manual provides detailed instructions for the Radiomaster R81, R84, R86, R86C, and R88 V2 series of 2.4GHz nano receivers. These receivers are designed for use with RC FPV Drones and are compatible with the FrSky D8 protocol, including transmitters like the TX16S. They offer a control distance of over 1km and support various channel configurations and output formats (SBUS/PWM).
Video: Overview of the Radiomaster Receiver Range, highlighting the different models.
Image: A selection of Radiomaster R81, R84, R86, R86C, R88 V2 receivers.
2. Specifications
The Radiomaster V2 receiver series offers various models, each with specific characteristics. All models operate on a 2.4GHz frequency range (2400-2483.5Mhz) and are compatible with the FrSky D8 signal format.
2.1. R81 Receiver
- Channels: 8
- Power Input Range: 4.5-6V
- Output Format: SBUS
- RSSI Support: Yes (on Ch9 of Sbus Output)
- Control Distance: >1km
- Antenna Length: Approximately 6cm
- Size: 17x11mm
- Weight: 2 grams
Image: Radiomaster R81 receiver with key specifications.
2.2. R84 Receiver
- Channels: 4
- Power Input Range: 4.5-8.4V
- Output Format: PWM
- Control Distance: >1km
- Antenna Length: 15cm
- Size: 30x15x5mm
- Weight: 3 grams
Image: Radiomaster R84 receiver showing channel labels and bind button.
2.3. R86 Receiver
- Channels: 6
- Power Input Range: 4.5-8.4V
- Output Format: PWM
- Control Distance: >1km
- Antenna Length: 15cm
- Size: 28x16.5x11mm
- Weight: 4.8 grams
Image: Radiomaster R86 receiver showing channel labels, dimensions, and weight.
2.4. R86C Receiver
- Channels: 6 (PWM), 8 (SBUS)
- Power Input Range: 4.5-8.4V
- Output Format: PWM, SBUS
- RSSI Support: Yes
- Control Distance: >1km
- Antenna Length: 15cm
- Size: 45x21.2x12.7mm
- Weight: 8 grams
Image: Radiomaster R86C receiver showing channel labels and bind button.
2.5. R88 Receiver
- Channels: 8
- Power Input Range: 4.5-8.4V
- Output Format: PWM
- RSSI Support: Yes
- Control Distance: >1km
- Antenna Length: 15cm
- Size: 40x26x16mm
- Weight: 11 grams
Image: Radiomaster R88 receiver showing channel labels, dimensions, and weight.
2.6. General Properties
- Material: Composite Material
- For Vehicle Type: Airplanes
- Tool Supplies: Assembled class
- RC Parts & Accs: Receiver
- Remote Control Peripherals/Devices: Remote Controller
- Recommend Age: 14+y
3. Setup and Binding
Before operating your receiver, it must be properly wired and bound to your compatible transmitter.
3.1. Wiring Instructions
Connect the receiver to your flight controller or servos according to the pinout diagrams provided below. Ensure correct polarity (positive, negative, signal) to avoid damage.
3.2. Binding Procedure (FrSky D8 Mode)
- Power on your transmitter and select the FrSky D8 protocol mode.
- Put your transmitter into BIND mode.
- Connect power to the receiver while holding down the BIND button (labeled 'BIND' or 'KEY' on the receiver).
- The LED on the receiver should flash rapidly, indicating it is in bind mode.
- Once the binding is successful, the LED on the receiver will turn solid or flash slowly, depending on the model.
- Exit BIND mode on your transmitter.
- Power cycle the receiver (disconnect and reconnect power).
- Verify that the receiver is now linked to the transmitter by checking servo response or flight controller input.
Important: These receivers are compatible with the FrSky D8 protocol. Ensure your transmitter is configured to use D8 mode for successful binding. They are generally not compatible with newer FrSky ACCST (D16) or ACCESS protocols unless specifically stated or if your transmitter supports D8 emulation.
4. Operation
Once bound, the receiver will output control signals to your flight controller or directly to servos. The specific output format depends on the receiver model:
- SBUS Output: R81 and R86C (when configured for SBUS) models provide a single serial bus output for all channels, typically connected to the SBUS input of a flight controller.
- PWM Output: R84, R86, R86C (when configured for PWM), and R88 models provide individual PWM outputs for each channel, suitable for direct connection to servos or flight controllers with PWM inputs.
Ensure your flight controller or servo connections match the receiver's output type and channel assignments.
5. Maintenance
- Antenna Placement: Ensure antennas are positioned correctly, ideally at a 90-degree angle to each other, and away from carbon fiber or metal parts to maximize signal reception. Do not cut or modify the antenna wires.
- Power Supply: Always provide power within the specified voltage range (4.5-6V for R81, 4.5-8.4V for others). Over-voltage can damage the receiver.
- Physical Protection: Protect the receiver from moisture, dust, and physical impact. Consider using heat shrink or a protective case if operating in harsh environments.
- Firmware Updates: Check the official Radiomaster website for any available firmware updates for your specific receiver model. Follow their instructions carefully for any update procedures.
6. Troubleshooting
- Receiver Not Binding:
- Ensure your transmitter is set to FrSky D8 mode.
- Verify the receiver is receiving power within its specified voltage range.
- Confirm you are holding the BIND button while connecting power to the receiver.
- Try moving the transmitter closer to the receiver during the binding process.
- No Signal/Intermittent Signal:
- Check antenna placement and ensure they are not obstructed or damaged.
- Verify all wiring connections are secure and correct.
- Ensure no other 2.4GHz devices are causing interference nearby.
- Confirm the receiver is still bound to the transmitter.
- Incorrect Channel Output:
- Check your flight controller or servo connections against the receiver's pinout diagram.
- Verify channel mapping in your flight controller software or transmitter settings.
- Receiver Appears Dead (No LED):
- Check power input voltage and polarity.
- Inspect for any visible damage to the receiver board.
7. User Tips
- Many users report excellent reliability with these receivers when properly set up.
- The V2 versions are generally considered an improvement over previous iterations.
- Always double-check your transmitter's protocol settings (ensure D8 mode is selected) to avoid binding issues, especially with newer transmitters that might default to ACCST or ACCESS.
8. Warranty and Support
For warranty claims, technical support, or further assistance, please refer to the official Radiomaster website or contact your point of purchase. Keep your proof of purchase for any warranty-related inquiries.