HITBOX TIG200

Contents

HITBOX TIG200 3-in-1 Welding Machine User Manual

MMA ARC HF TIG IGBT Inverter Stick Welder Machine

1. Safety Instructions

This manual contains important information on the safe use, maintenance, and operation of the HITBOX TIG200 welding machine. Please read all safety instructions carefully before initial use to ensure personal safety and the safety of the working environment.

1.1 General Precautions

  • Always operate the machine according to the instructions provided.
  • The manufacturer is not responsible for mistakes or omissions due to operation outside of this manual.
  • Contents may be revised without prior notice.

1.2 Electrical Safety

Warning symbol for electric shock
Beware of electric shock!
  • Install grounding device according to application standards.
  • Do not touch live parts with bare skin, wet gloves, or wet clothes.
  • Ensure you are insulated from ground and workpiece.
  • Cover the machine before powering on to avoid electric shock.
  • Confirm the safety of your working position.

1.3 Fire and Explosion Hazards

Warning symbol for fire hazard
Beware of fire hazard!
  • Install the machine on non-combustible materials.
  • Ensure no flammable materials are near the welding position.
Warning symbol for explosion hazard
Beware of explosion!
  • Do not install the machine in an environment with explosive gas.

1.4 Health and Physical Safety

  • Smoke may be harmful to your health! Keep your head away from smoke. Ensure good ventilation with exhaust equipment.
  • Arc radiation may hurt your eyes and burn your skin! Use proper mask and protective clothing.
  • Magnetic fields can affect pacemakers. Consult a doctor if you have a pacemaker.
  • Hot workpiece can cause severe scald. Do not touch hot workpieces with bare hands.
  • Excessive noise can harm hearing. Wear ear covers or other hearing protectors.
  • Moving parts may injure your body. Keep away from moving parts like the cooling fan.

1.5 Handling and Component Replacement

  • Replacing components can be dangerous; only professionals should perform this.
  • Ensure no foreign bodies fall into the machine during component replacement.
  • Verify correct wiring after replacing PCBs.
  • Carrying or moving the machine can be dangerous. Cut input power before moving.
  • The handle is for short-distance movement only, not for lifting.
  • Ensure flying rings are tightened and enclosure is fixed when moving with a crane.
  • Use two lifting belts for crane movement, with an angle less than 15° to the vertical.
  • Do not apply stress on the operation panel or cover when moving.
  • Do not operate a damaged machine or one with missing components.

2. General Description

The HITBOX TIG200 is a versatile 3-in-1 welding machine designed for MMA (Manual Metal Arc), ARC, and HF TIG (High-Frequency Tungsten Inert Gas) welding processes. It features IGBT inverter technology for stable and efficient performance.

2.1 Model Coding

The model name TIG200 indicates an Inverter AR TIG welding machine.

2.2 Key Features

Key features of the HITBOX TIG200 welding machine including dual voltage, IGBT technology, and various protections.

Figure 2.1: Key Features Overview

  • Dual Voltage: Operates on AC220V/AC110V ±15% 50Hz/60Hz.
  • Good Heat Dissipation: Efficient cooling system.
  • Hot Start: Improves arc ignition for MMA welding.
  • Arc Force: Prevents electrode sticking during MMA welding.
  • Anti-stick: Reduces electrode sticking.
  • Latest IGBT Technology: Ensures stable current output and high efficiency.
  • Overcurrent Protection: Safeguards the machine from damage.
  • High Duty Cycle: Allows for extended welding periods.
  • Post Gas Function: Variable air post time (1-10 seconds) from the torch helps cool the torch and consumables, enhancing their durability.
Close-up of the HITBOX TIG200 control panel showing the 'S' knob for Post Gas adjustment (1-10 seconds).

Figure 2.2: Post Gas Function Control

2.3 Applications

Examples of materials the HITBOX TIG200 can weld: mild steel, stainless steel, steel plate, square pipe, carbon steel, and copper.

Figure 2.3: Wide Range of Weldable Materials

Examples of common applications for the HITBOX TIG200, including DIY projects, repair work, building, and welding doors and windows.

Figure 2.4: Common Applications

The TIG200 is suitable for welding:

  • Mild Steel
  • Stainless Steel
  • Steel Plate
  • Square Pipe
  • Carbon Steel
  • Copper

Common applications include DIY projects, repair work, building, and welding doors & windows.

3. Specifications

3.1 General Technical Parameters

ParameterValue
Model NumberTIG200
Rated Input PowerAC220V/AC110V ±15% 50Hz/60Hz
Rated Input Capacity (kVA)6.8
Rated Input Current (A)TIG: 28, MMA: 35
Rated Output Current/Voltage (A/V) @220VTIG: 160A/16.4V, MMA: 140A/25.6V
Rated Output Current/Voltage (A/V) @110VTIG: 140A/16.4V, MMA: 120A/25.6V
Rated Duty Cycle (@40°C)60%
No-load voltage (V)DC62
Output Current Range (A) @220VTIG: 10-200, MMA: 20-160
Output Current Range (A) @110VTIG: 10-140, MMA: 20-120
Post-flow Time (s)0-10
Arc Ignition TypeHF
Enclosure Protection ClassIP21S
Insulation GradeF
Power Factor0.73
Efficiency (%)80

3.2 Size and Weight

Diagram showing the HITBOX TIG200 welder and its included accessories with dimensions and weight.

Figure 3.1: Accessories, Size, and Weight

ParameterValue
Overall Size (L*W*H)395mm * 153mm * 301mm (13.8" x 5.9" x 12.6")
Weight7 kg (12.1 lbs)

3.3 System Characteristics

Graph illustrating the duty cycle of the welding machine, showing the percentage of time it can operate within a 10-minute cycle.

Figure 3.2: Duty Cycle Curve

Duty Cycle: Rated duty cycle means that taking 10 minutes as a time cycle, the ratio of rated output time is taken in that time cycle.

Graph showing the output characteristic curves of the welding machine, including maximum output, minimum output, and relationship with rated load.

Figure 3.3: Output Characteristic Curves

Output Characteristics: The welder exhibits constant current external characteristics, meaning the welding current remains stable regardless of arc length.

4. Setup and Connection

4.1 Installation Requirements

Ensure the installation environment meets safety standards, including proper grounding and ventilation.

4.2 Panel Introduction

Detailed diagram of the HITBOX TIG200 front and rear panels with numbered components and their functions.

Figure 4.1: Front and Rear Panel Layout

No.Part NameFunction
1Current DisplayTo display the current
2Power IndicatorIndicator light when the power supply is energized
3Overheating/Overcurrent IndicatorTo indicate high internal temperature or overheating protection status
4Welding Mode ButtonSelect TIG or ARC mode
5Current Adjustment Knob (A)To adjust the output current value
6Post Gas Adjustment Knob (S)Controls gas post-flow timing (1-10s)
7Positive Terminal (+)To connect the earth cable (MMA) or TIG torch (TIG)
8Negative Terminal (-)To connect the TIG torch (TIG) or electrode holder (MMA)
9Torch ConnectionFor TIG torch connection
10Gas InGas input connection
APower SwitchControls ON/OFF of the input power
BInput AC 110V/220VPower supply input

4.3 Connection Method

Diagram illustrating the connection methods for MMA and HF TIG welding with the HITBOX TIG200.

Figure 4.2: MMA and HF TIG Connection Ways

4.3.1 Input Cable Connection

  • Ensure the product power plug is grounded.
  • Connect the primary power supply cable to the rated input power.
  • Ensure the primary cable is tightly connected to the correct socket.
  • Verify voltage with a multi-meter is within the acceptable range.
  • The cross-section of leads in the switching box must meet maximum input capacity requirements.

4.3.2 Output Cable Connection

  • Line Disconnecting Switch: Install a switch at each power supply to immediately cut off power in emergencies. The switch's disconnecting value should be equal to or greater than the continuous rating of the fuse. The switch should cut power when in the "OFF" position.
  • TIG Torch Connection: Connect the center plug of the TIG torch to the center socket on the front panel and tighten clockwise to prevent gas leakage.
  • Earth Cable Connection: Insert the quick plug of the earth cable into the output terminal "+" on the front panel and tighten clockwise.

5. Operating Instructions

5.1 TIG Operation

  1. Turn the power switch to "ON". The power indicator light will illuminate, and the cooling fan will start.
  2. Open the argon bottle valve and adjust the gas flow meter according to welding needs.
  3. Press the switch on the welding gun. The solenoid valve will activate, and you will hear a high-frequency spark discharge. Argon gas will flow from the welding gun.
  4. Note for first-time welding: Press and hold the gun switch for a few seconds before welding to exhaust all air from the gas circuit.
  5. Post-flow: After stopping welding, keep the welding torch in position for a few seconds to allow argon gas to protect the welded joints during cooling.
  6. Pulse Function: If using the pulse function, select the pulse frequency using the "pulse selector switch".
    • "Lower" for no pulse.
    • "Middle" for medium-frequency pulse (e.g., 200Hz).
    • "Upper" for low-frequency pulse (e.g., 2Hz).
  7. Adjust the current attenuation time knob or button based on workpiece and welding requirements.
  8. Set the welding current according to the thickness of the workpiece.
  9. Maintain a 2-4mm distance between the tungsten electrode and the workpiece. Press the gun switch to initiate high-frequency discharge and arc ignition.
  10. Once the arc is ignited, the high-frequency arc sparks will disappear, and welding will commence.

5.2 MMA Operation

  1. Turn the power switch to "ON". The cooling fan should start.
  2. Set the function switch on the front panel to the downward position for manual welding mode.
  3. Set the appropriate welding current based on workpiece thickness, workstation, and process conditions.
Plate Thickness (mm)Amount of Current (A)Tungsten Diameter (mm)Wire Diameter (mm)Gas Flow Rate (L/min)
Stainless SteelsCopperTitanium
0.3~0.510~401.01.0466
0.5~1.020~401.01.0466
1.0~2.040~701.61.64~68~106~8
2.0~3.080~1302.0~2.52.08~1010~128~10
3.0~4.0120~1702.5~3.02.510~1210~1510~12
4.0160~2003.03.010~1412~1812~14

6. Maintenance

Regular maintenance is crucial for the high performance and safe operation of your welding machine. Always shut down the power of the switching box and the cutting machine before performing any checks or maintenance.

6.1 Daily Maintenance

Perform the following checks daily. Clean or replace components as necessary. Use components provided or recommended by the dealer for replacements.

ItemChecking RequirementsRemarks
Front panel
  • Check for damaged or loosely connected components.
  • Ensure output quick sockets are tightened.
  • Verify abnormity indicator is not illuminated.
If unqualified, check the interior of the machine, tighten or replace components.
Back panel
  • Check input power cable and buckle condition.
  • Ensure air intake is unobstructed.
CoverCheck if bolts are loosely connected.
Side platesCheck if the side plate is loosely fixed.If unqualified, tighten or replace the components.
ChassisCheck if screws are loosely connected.
Routine
  • Check for color fading or overheating problems on the enclosure.
  • Verify fan sounds normal when running.
  • Check for abnormal smell, vibration, or noise.
If abnormal, check the interior of the machine.
Earth cableCheck if grounding wires (workpiece GND wire and machine GND wire) are broken off.If unqualified, tighten or replace the components.
Cutting cable
  • Check if the insulating layer is worn or conductive part is exposed.
  • Check if the cable is drawn by external force.
  • Ensure the cable connected to the workpiece is well connected.
Use appropriate methods for safety and normal cutting.

6.2 Periodic Check

Periodic checks should be carried out by qualified professionals to ensure safety. The power of the switching box and the cutting machine should be shut down before periodic check. Wait 5 minutes after shutting down the machine before proceeding.

  • Safety: All maintenance and checking should be carried out after the power is completely cut off. Make sure the power plug of the machine is pulled out before uncovering the cutting machine.
  • Periodic Check Frequency: Check periodically whether inner circuit connection is in good condition (esp. plugs). Tighten the loose connection. If there is oxidization, remove it with sandpaper and then reconnect. Check periodically whether the insulating layer of all cables is in good condition. If there is any dilapidation, rewrap it or replace it.
  • Beware of Static: To protect semiconductor components and PCBs from static damage, wear antistatic device or touch the metal part of the enclosure to remove static in advance before contacting the conductors and PCBs of the machine internal wiring.
  • Keep it Dry: Avoid rain, water, and vapor infiltrating the machine. If there is, dry it and check the insulation of the cutting machine (including that between the connections and that between the connection and the enclosure) with an ohmmeter. Only when there are no abnormal phenomena anymore, can the machine be used. Put the machine into the original packing in dry location if it is not to be used for a long time.
  • Pay Attention to Maintenance: Periodic check should be carried out to ensure the long-term normal use of the machine. Be careful when doing the periodic check, including the inspection and cleaning of the machine interior. Generally, periodic check should be carried out every 6 months, and it should be carried out every 3 months if the cutting environment is dusty or with heavy oily smoke.

7. Troubleshooting

The abnormity indicator on the front panel will illuminate in case of any failures inside the cutting machine. Refer to the table below for common issues and their solutions.

Malfunction PhenomenaCause and Solution
Turn on the machine, power indicator illuminates, control PCB keys do not function, no response when pushing torch trigger.The cutting machine has crashed: Shut down the machine and restart it.
Turn on the machine, power indicator illuminates, control PCB keys work normally, but no response when pushing torch trigger.
  • The LED1 on the main board is on: The control PCB is damaged.
  • The LED1 on the main board is off: Check the torch trigger and torch trigger wire.
Turn on the machine, power indicator illuminates, fan works. When pushing torch trigger, solenoid valve functions, but no HF discharge rustling.The arc ignition part fails:
  • The interelectrode distance of the discharge nozzle is too long.
  • There is leakage of the HF capacitor 102/10KV.
  • The relay is damaged.
  • The input voltage is too low.
Arc cannot be ignited.The air pressure is overly high or overly low.

8. User Tips

  • Aluminum Welding: The HITBOX TIG200 is a DC TIG machine (No-load voltage DC62). While DC TIG is excellent for steel, stainless steel, and copper, it is generally not suitable for welding aluminum. Aluminum typically requires an AC TIG welder for effective cleaning action and penetration.
  • Gas Flow: Always ensure adequate gas flow for TIG welding to protect the weld puddle and tungsten from atmospheric contamination. Adjust according to the material and current settings.
  • Electrode Preparation: Proper preparation of the tungsten electrode (grinding to a sharp point for DC TIG) is crucial for a stable arc and quality weld.

9. Warranty and Support

This product is manufactured by SHENGZHEN UNITWELD WELDING AND MOTOR CO;LTD. The product meets IEC60974-1 international safety standards and relevant Chinese standards.

For technical parameters, detailed instructions, or any inaccuracies found in this manual, please contact the manufacturer or your dealer for support.

A comprehensive user manual in PDF format is available for download and reference. You can access it via the following link: HITBOX TIG200 User Manual (PDF)

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.