Introduction
Thank you for choosing the FIREGAS 52 cm Built-in Extractor Hood. This manual provides essential information for the safe and efficient installation, operation, and maintenance of your new kitchen appliance. Please read these instructions carefully before use and keep them for future reference.
Product Overview
The FIREGAS 52 cm Built-in Extractor Hood is designed for seamless integration into your kitchen cabinetry, offering powerful and quiet ventilation. It features 3 speed settings, a durable stainless steel construction, and can operate in both recirculation and extraction modes.
Figure 1: Front view of the FIREGAS 52 cm Built-in Extractor Hood, including two charcoal filters.
Figure 2: Seamless integration of the extractor hood into a modern kitchen, enhancing aesthetics.
Specifications
| Feature | Specification |
|---|---|
| Brand | FIREGAS |
| Product Dimensions (D x W x H) | 29.1 cm x 52.5 cm x 27.6 cm |
| Special Feature | Built-in oil collector |
| Air Flow Capacity | Up to 300 m³/hour |
| Material | Stainless steel |
| Noise Level | 63 dB(A) |
| Mounting Type | Insert mount |
| Included Components | 2 carbon filters (CC110*2) |
| Control Type | Knob (5 knobs) |
| Light Source Type | LED (2W) |
| Power Source | AC |
| Power (W) | 200W |
| Exhaust Type | Combination |
| Voltage | 220 V |
| High-concerned chemical | None |
Figure 3: High Efficiency Motor features: Energy Efficiency, Powerful, Long-lasting.
Setup and Installation
The FIREGAS extractor hood is designed for insert mounting, allowing it to be discreetly hidden within your kitchen cabinetry. Professional installation is recommended to ensure proper functionality and safety.
Installation Modes:
- Recirculation Mode: This mode uses the included carbon filters (CC110*2) to filter cooking oil stains and odors from the air, then releases the purified air back into the kitchen. Carbon filters must be replaced periodically.
- Extraction Mode: For this mode, activated carbon is not required. The hood expels fumes and odors to the outside of the house through a duct (not included). This provides truly fresh kitchen air. Ensure proper ducting is installed according to local building codes.
Figure 4: The extractor hood seamlessly installed under a kitchen cabinet.
Operating Instructions
The extractor hood is controlled via 5 simple knobs located on the front panel.
- Power On/Off: Use the designated knob to turn the hood on or off.
- Speed Selection: Choose from 3 available speeds to adjust the extraction power according to your cooking needs. Higher speeds are suitable for heavy cooking, while lower speeds are ideal for simmering. The maximum extraction rate is 300 m³/h.
- LED Lighting: Activate the 2W LED light to illuminate your cooking area for better visibility.
Figure 5: Demonstrating the powerful suction with a maximum extraction rate of 300 m³/h.
Maintenance
Regular maintenance ensures optimal performance and longevity of your extractor hood.
Grease Filters:
The hood features multi-layer washable aluminum grease filters. These filters effectively trap grease and are easy to remove and clean for reuse.
- Removal: Gently unlatch and pull down the aluminum filters.
- Cleaning: Wash the filters by hand with warm, soapy water or place them in a dishwasher. Ensure they are completely dry before re-installing.
- Frequency: Clean grease filters regularly, typically every 2-4 weeks depending on cooking frequency.
Carbon Filters (for Recirculation Mode):
If operating in recirculation mode, the carbon filters (CC110*2) are crucial for odor removal. These filters are not washable and must be replaced periodically.
- Replacement: Refer to the specific instructions for replacing CC110 carbon filters. Typically, they twist or clip into place.
- Frequency: Replace carbon filters every 3-6 months, or more frequently if cooking heavily or noticing persistent odors.
Built-in Oil Collector:
The built-in oil collector should be emptied and cleaned regularly to prevent overflow and maintain hygiene.
- Emptying: Carefully remove the oil collector tray.
- Cleaning: Wash with warm, soapy water and dry thoroughly before re-inserting.
Figure 6: Aluminum Filter benefits: Durable, Rustproof, Efficient, Easy-Clean, Odor-Free.
Troubleshooting
If you encounter any issues with your extractor hood, please refer to the following common troubleshooting steps:
- Hood not turning on: Check if the power cord is securely plugged into a working outlet. Verify that the circuit breaker has not tripped.
- Poor suction: Ensure the grease filters are clean and not clogged. If in recirculation mode, check if the carbon filters need replacement. For extraction mode, verify that the ducting is clear and unobstructed.
- Excessive noise: Check for any loose parts or obstructions in the fan. Ensure the hood is securely mounted. A noise level of 63 dB(A) is normal during operation.
- Lights not working: Check if the LED bulb is securely in place. If the bulb is faulty, it may need replacement.
If the problem persists after performing these checks, please contact customer support.
User Tips
- For optimal performance, turn on the extractor hood a few minutes before you start cooking and leave it running for a few minutes after you finish to clear residual odors and steam.
- Always use the appropriate fan speed for the type of cooking you are doing. Higher speeds are best for frying or grilling, while lower speeds are sufficient for simmering.
- Regularly clean the exterior of the hood with a soft cloth and mild detergent to maintain its stainless steel finish. Avoid abrasive cleaners.
Warranty and Support
For warranty information or technical support, please refer to the documentation provided at the time of purchase or contact your retailer. Keep your proof of purchase for any warranty claims.