1. Introduction
The Hantek 1008C is a cost-effective PC USB 8-channel automotive diagnostic oscilloscope, DAQ (Data Acquisition), and programmable signal generator. It is designed for efficient and precise vehicle testing and general oscilloscope applications. This device features a 2.4MSa/s real-time sampling rate, 12-bit vertical resolution, and spectrum analysis capabilities. It connects to your computer via a USB 2.0 interface, requiring no external power supply, and is compatible with various Windows operating systems.
2. Key Features
- 8-Channel Oscilloscope: Designed specifically for vehicle testing.
- High Performance: 2.4MSa/s real-time sampling rate, 12-bit vertical resolution.
- Automotive Diagnostic Functions: Over 80 types of diagnostic functions including:
- First Diagnosis: Intake manifold vacuum & ignition, Petrol fumes adjusting valve vacuum & ignition, Idle exhaust ignition, Starting exhaust ignition.
- Ignition: Primary and secondary.
- Sensor Testing: Air Flow Meter, Camshaft, Crankshaft, Distributor, Lambda sensor, Throttle position.
- Bus Diagnosis: CAN bus data examine, CAN bus signal integrity, CAN bus LH long time acquisition, LIN bus.
- Performer: Petrol/Diesel.
- Starter and charging circuits.
- Programmable Signal Generator: 8 channels capable of analog signals for crankshaft, camshaft, etc.
- Spectrum Analysis Function.
- Easy Connectivity: USB 2.0 interface, plug and play, no external power required.
- User-Friendly Software: Intuitive interface similar to benchtop oscilloscopes, with more than 20 types of automatic testing functions.
- Multilanguage Support: Software supports English, German, and Chinese.


3. Package Contents
The standard package includes the following items:
- 1 x Hantek 1008C DAQ Oscilloscope
- 1 x Auto-probe (HT25 high voltage ignition probe, included in 1008C, not 1008A)
- 4 x Crocodile probes/cables
- 4 x BNC Connectors
- 1 x USB Cable
- 1 x CD (containing driver software and manual)



4. Product Overview
4.1 Device Dimensions

4.2 Front and Back Panel Layout

- CH1-CH8: BNC input connectors for the 8 analog channels.
- Signal Generator: Output port for programmable signal generation.
- USB Interface: USB 2.0 port for connecting to a PC.
5. Setup Instructions
5.1 Software Installation
- Insert the provided CD into your computer's CD-ROM drive.
- Follow the on-screen instructions to install the Hantek 1008C software.
- The software supports Windows NT, Window 2000, Windows XP, VISTA, Windows 7/8/10 (32 BIT and 64 BIT).
- No additional drivers are typically needed as the device is plug-and-play via USB 2.0.
5.2 Hardware Connection
- Connect the Hantek 1008C oscilloscope to your computer using the provided USB cable.
- Ensure the software is running on your PC.
- Connect the appropriate probes (e.g., crocodile clips, BNC connectors, auto-probe) to the desired input channels (CH1-CH8) on the oscilloscope.
- Connect the other end of the probes to the test points on the vehicle or circuit you wish to analyze.

6. Operating Instructions
6.1 General Oscilloscope Use
- Launch the Hantek 1008C software on your PC.
- Select the desired function from the main interface (e.g., Vehicle Diagnosis, Oscilloscope, Generator).
- Adjust the time base range, input sensitivity, and trigger settings as needed for your measurement.
- The software provides 20 types of automatic measurement methods for convenient and visual result readout.
- Diagnostic results can be generated as reports, printed, or saved as screenshots.
6.2 Automotive Diagnostics
The Hantek 1008C offers extensive automotive diagnostic functions. For specific tests:
- In the software, navigate to the 'Vehicle Diagnosis' module.
- Select the specific system or component you wish to test (e.g., Ignition, Sensors, Bus Diagnosis).
- Follow the on-screen prompts or refer to the service manual for proper connection points and test procedures.
- The software includes a video help function for guidance.


6.3 CAN Bus Testing Example
The following video demonstrates how to perform CAN bus detection using the Hantek 1008C. This involves connecting test leads to the CAN H and CAN L terminals of the ECU and observing the waveforms on the oscilloscope software.
6.4 Signal Generator Function
The 8-channel programmable generator can simulate crankshaft and camshaft signals, which is useful for testing and diagnostics.
7. Specifications
| Category | Parameter | Value |
|---|---|---|
| Model | Hantek 1008C | |
| Vertical | Analog Channel | 8 |
| Input Impedance | Resistance: 1MΩ | |
| Input Sensitivity | 10mV/div to 5V/div | |
| Input Coupling | DC | |
| Resolution | 12 bits | |
| Horizontal | Memory Depth | 4K |
| Max. Input | 400V (DC+AC Peak) | |
| Real-Time Sampling Rate | 2.4MSa/s | |
| Time Base Range | 1ns/div to 20000s/div (1-2-5 sequences) | |
| Time Base Precision | ±50ppm | |
| Trigger | Source | CH1, CH2, CH3, CH4, CH5, CH6, CH7, CH8 |
| Mode | Edge | |
| X-Y Mode | X-Axis Input | CH1 |
| Y-Axis Input | CH2 | |
| Cursors and Measurement | Voltage Measurement | Vpp, Vamp, Vmax, Vmin, Vtop, Vmid, Vbase, Vavg, Vrms, Vcrms, Preshoot, Overshoot |
| Time Measurement | Frequency, Period, Rise Time, Fall Time, Positive Width, Negative Width, Duty Cycle | |
| Cursors Measurement | Horizontal, Vertical, Track, Auto Measure Modes | |
| Waveform Signal Process | +, -, x, ÷, FFT, Invert | |
| Voltage Range | 10mV to 5V/div @ x 1 probe | |
| 100mV to 50V/div @ x 10 probe | ||
| 10V to 5000V/div @ x 1000 probe | ||
| 100V to 50000V/div @ x 10000 probe | ||
| 200mV to 100V/div @ 20:1 | ||
| Current Range | 100mA to 50.0A/div @ CC65(20A) | |
| 1000mA to 500.0A/div @ CC65(65A) | ||
| 1A to 100.0A/div @ CC650(60A) | ||
| 10A to 1000.0A/div @ CC650(650A) | ||
| 1A to 200.0A/div @ CC1100(100A) | ||
| 10A to 2000.0A/div @ CC1100(1100A) | ||
| Cursor | Time/frequency difference, voltage difference | |
| FFT | Rectangular, Hanning, Hamming, Blackman Window | |
| Math | Addition, subtraction, multiplication, division | |
| Programmable Generator | ||
| Channel | 8 | |
| Output Level | LVTTL | |
| Frequency Range | 0-250kHz | |
| Interface | USB 2.0 | |
| Power | No need extra power supply | |
| Physical | Size | 185 x 150 x 27 (mm) |
| Weight | 0.35KG | |
8. Troubleshooting
- Software not recognizing device: Ensure the USB cable is securely connected to both the oscilloscope and the PC. Verify that the software drivers were installed correctly from the provided CD. Try connecting to a different USB port.
- No waveform displayed: Check probe connections to both the oscilloscope and the test point. Ensure the input sensitivity and time base settings in the software are appropriate for the signal being measured. Verify the trigger settings are correctly configured.
- Software language issue: The device language is available in English, German, and Chinese. If you are experiencing issues with the language, check the software settings for language selection.
- Inaccurate readings: Ensure probes are correctly calibrated and connected. Check for any loose connections or damaged cables.
9. Maintenance
- Cleaning: Use a soft, dry cloth to clean the device. Do not use abrasive cleaners or solvents.
- Storage: Store the oscilloscope and its accessories in a dry, dust-free environment, preferably in its original carrying case, when not in use.
- Cable Care: Avoid bending or kinking the USB cable and probes excessively to prevent internal damage.
- Software Updates: Periodically check the manufacturer's website for software updates to ensure optimal performance and access to new features.
10. Warranty and Support
For warranty information, technical support, or service inquiries, please refer to the documentation included with your purchase or contact the seller directly. Keep your purchase receipt as proof of purchase.