Dahao A18 A58

Contents

Dahao A18/A58 Embroidery Machine Control Panel LCD Screen User Manual

Original New LCD Screen for Dahao Operation Box Control Panel

1. Introduction

This manual provides essential information for the installation, operation, maintenance, and troubleshooting of your new LCD screen for Dahao A18 and A58 series embroidery machine operation box control panels. Please read this manual thoroughly before installation and use to ensure proper function and longevity of the product.

2. Safety Information

  • Always disconnect power to the embroidery machine before attempting any installation or maintenance.
  • Handle the LCD screen with care to avoid damage to the display surface or internal components.
  • Ensure proper grounding of the embroidery machine to prevent electrical hazards.
  • Only qualified personnel should perform installation or repair procedures.
  • Keep the screen away from liquids and excessive moisture.

3. Package Contents

Verify that all items are present and undamaged upon receipt:

  • 1 x Original New LCD Screen for Dahao A18/A58 Operation Box Control Panel

4. Specifications

FeatureDescription
Part NameOriginal New LCD Screen For Dahao Operation Box Control Panel A18 A58
CompatibilityDahao A18, Dahao A58 Embroidery Machine Operation Boxes
MaterialPlastic and Metal
UseEmbroidery Machine Mechanical Parts
TypeMechanical Parts
OriginMainland China
Set TypeNo
High-concerned chemicalNone
Touchscreen FunctionalityNot explicitly stated as touchscreen. Operation typically via physical buttons on the control panel.

5. Installation and Setup

This section outlines the general steps for replacing or installing the LCD screen. Specific procedures may vary slightly depending on your exact Dahao machine model. Always refer to your embroidery machine's primary service manual for detailed instructions.

  1. Power Disconnection: Turn off the embroidery machine and disconnect it from the main power supply.
  2. Access Control Panel: Carefully open the embroidery machine's operation box control panel to access the existing LCD screen or the mounting area.
  3. Remove Old Screen (if applicable):
    • Disconnect any cables (e.g., data, power) attached to the old LCD screen.
    • Unscrew or unclip the old screen from its mounting brackets.
  4. Install New Screen:
    • Position the new LCD screen into the control panel housing.
    • Secure the screen using the appropriate screws or clips.
    • Connect the data and power cables to the new LCD screen. Ensure all connections are firm and correctly oriented.
    Back of the LCD screen showing connectors and model number LSAA04T0001
    Figure 5.1: Back of the LCD screen, showing connection points and identification labels (GP LSAA04T0001, S/N 126036021278).
    Front view of the LCD screen
    Figure 5.2: Front view of the LCD screen, ready for installation.
  5. Verify Compatibility: Confirm the model number on your operation box matches the compatible models (A18, A58).
    Label on Dahao A58 Operation Box showing model A58-B104L
    Figure 5.3: Example of an Operation Box label, indicating model A58-B104L.
  6. Close Control Panel: Carefully close and secure the control panel cover.
  7. Initial Power-Up: Reconnect the machine to power and turn it on. Observe the screen for proper display.

6. Operation

The LCD screen serves as the primary visual interface for your Dahao embroidery machine's control panel. It displays critical information such as:

  • Current embroidery design and progress
  • Machine status and error messages
  • RPM (Revolutions Per Minute)
  • Stitch count and coordinates
  • Menu navigation for machine settings and functions

Interaction with the machine is typically performed using the physical buttons and controls located around the LCD screen on the operation box. Refer to your embroidery machine's main user manual for detailed instructions on navigating menus and operating specific functions.

Dahao embroidery machine control panel with LCD screen displaying a design and machine parameters
Figure 6.1: LCD screen in operation, showing a design and machine data on a Dahao control panel.

7. Maintenance

  • Cleaning: Use a soft, lint-free cloth slightly dampened with a non-abrasive screen cleaner or water to gently wipe the display surface. Avoid harsh chemicals or abrasive materials that could scratch the screen.
  • Protection: Avoid direct impact or pressure on the LCD screen. When not in use, ensure the control panel cover is closed to protect the screen from dust and debris.
  • Environmental Conditions: Operate the machine in a clean, dry environment within recommended temperature and humidity ranges to prevent damage to electronic components.

8. Troubleshooting

ProblemPossible CauseSolution
Screen does not turn onNo power, loose cable connection, faulty screen.
  • Check if the embroidery machine is powered on.
  • Verify all cables to the LCD screen are securely connected.
  • If problem persists, contact technical support.
Garbled or distorted displayLoose data cable, incompatible screen, internal fault.
  • Ensure data cables are properly seated.
  • Confirm the screen model is correct for your machine.
  • Restart the embroidery machine.
  • If problem persists, contact technical support.
Screen is dim or flickeringBacklight issue, power supply problem.
  • Check machine power supply.
  • If problem persists, contact technical support.

9. User Tips

  • Touchscreen Inquiry: Based on common questions, please note that this LCD screen is designed for Dahao operation boxes which typically utilize physical buttons for input. It is not explicitly stated to be a touchscreen. If your original panel was a touchscreen, verify compatibility with the seller before purchase.
  • Model Verification: Always double-check the model number of your Dahao operation box (e.g., A18, A58) against the product's compatibility list to ensure a perfect fit and function.
  • Professional Installation: While installation can be straightforward, if you are unsure, consider having a qualified technician perform the replacement to avoid damage to the screen or machine.

10. Warranty and Support

For warranty information, technical support, or to inquire about additional spare parts, please contact your original seller or the manufacturer directly. Keep your purchase records handy when seeking support.

Qingdao Sunwing Embroidery Machine Co., Ltd. is a professional supplier of embroidery machine spare parts and electronic boards. They supply parts for Barudan, Tajima, SWF, and Chinese embroidery machines, known for stable good quality, fast delivery, and excellent after-sales service.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.