1. Introduction
The DSPIAE AT-AP Multi-Purpose Support Platform is a versatile tool designed to assist model makers and hobbyists with various precision tasks. Crafted from durable aluminum alloy with an anodized surface, this platform offers multiple functions including cutting, drilling, chamfering, and shaping plastic rods and sheets. It aims to reduce the need for numerous specialized tools and enhance precision in your projects.

2. Package Contents & Initial Setup
Upon unboxing, verify that all components are present:
- DSPIAE AT-AP Multi-Purpose Support Platform
- Hex Wrench
- Instruction Manual (this document)
The platform is designed for immediate use. No complex assembly is required. If any blades need to be installed or adjusted, use the provided hex wrench.

3. Operating Instructions
The AT-AP platform offers nine major functions to streamline your model making process. Familiarize yourself with each module before use.
3.1. Product Demonstration Video
3.2. Fixed Angle Cutting
Utilize the marked angles (30°, 45°, 60°, 75°, 90°) and the 0-34mm gauge for precise angular cuts on plastic sheets. Place the material against the desired angle guide and use a hobby knife or blade to cut.

3.3. Equal Width Cutting
Achieve consistent strip widths by using the fixed width cutting guides. Insert your plastic sheet and cut along the designated lines to produce strips of uniform width.

3.4. Joining Plastic Sheets
The platform provides guides for joining plastic sheets at various angles (e.g., 90°, 45°, 135°, 60°, 30°, 120°). For stronger bonds, chamfering the joining edges can provide a larger contact area. The platform also supports plastic sheet corner cutting.

3.5. Plastic Sheet Chamfering
Chamfer plastic sheets with precision, supporting 1-10mm chamfering. The platform supports a maximum cutting length of 44mm. A broad hobby blade is recommended for this task.

3.6. Half Circle or Triangular Rod Making
Transform square plastic rods into half-circle or triangular shapes. Insert the rod into the appropriate guide and carefully sand or cut away the unwanted section. Examples for 1mm and 2mm square rods are provided.

3.7. Plastic Rods Beveling
Achieve perfectly beveled plastic rods with ease. The platform supports beveling using a 6mm wide blade. Insert the rod and use the guide for consistent results.

3.8. Vertical Drilling & Precision Center Drilling
The platform aids in vertical drilling and precision center drilling for plastic rods. It supports drill bits with a 3.175mm shank. For center drilling, adjust the slider to align with plastic rods ranging from 1.5mm to 10.5mm in diameter.


4. Maintenance
- **Handling**: DO NOT knock or drop the product to avoid deformation and unavailability.
- **Storage**: Keep the platform properly after use to avoid damage caused by accidental falling.
- **Cleaning**: Regularly clean the platform to remove plastic dust and debris. A soft cloth or wipe is recommended.
- **Blade Replacement**: After prolonged use, the cutting blades may become dull. They can be easily replaced with a new 6mm wide blade.
- **Surface Care**: DO NOT scratch the product surface with hard objects to avoid damaging the appearance.
5. Troubleshooting
This section addresses common issues encountered during model making that the AT-AP platform is designed to resolve.
- **Inaccurate Angles/Offset Drilling**: Ensure your material is firmly seated against the guides and that the tool is held steady during operation. The platform's design is intended to eliminate freehand errors.
- **Difficulty Locating Center of Rods**: Use the precision center drilling guide and adjust the slider to match the rod's diameter for accurate centering.
- **Dull Blades**: If cuts are rough or require excessive force, the blade may be dull. Refer to the Maintenance section for blade replacement.

6. Specifications
| Feature | Detail |
|---|---|
| Product Name | Multi-Purpose Processing Assistance Platform |
| Model Number | AT-AP |
| Dimensions | 62mm x 42mm x 42mm |
| Net Weight | 180 ± 3g |
| Material | Aluminum Alloy |
| Application | Wood Working Tool (General Hobby Tool) |
| DIY Supplies | Electrical (General Hobby Tool) |
| Package | Case |
Precautions:
- It is forbidden for children under the age of 14 to use this tool to avoid injury caused by sharp parts.

7. User Tips
No specific user tips were available from reviews or Q&A for this product. However, general tips for using precision hobby tools include:
- Always work in a well-lit area.
- Ensure your work surface is stable and clean.
- Use light, controlled pressure when cutting or drilling to prevent damage to the material or the tool.
- Practice on scrap materials before working on your final project.
8. Warranty & Support
For any product inquiries, technical support, or warranty information, please contact the seller directly or visit the official DSPIAE website at www.dspiae.com.