ACEMIC G6 Dynamic Wireless Microphone System User Manual

1. Introduction

The ACEMIC G6 is a high-performance 2.4GHz dynamic wireless microphone system designed to provide reliable and high-fidelity audio transmission. With its 24-bit/48kHz audio sampling rate and ultra-low latency, it ensures clear and professional sound for various applications. This manual will guide you through the setup, operation, and maintenance of your G6 system.

2. Package Contents

Please check the package for the following items:

• ACEMIC G6 Wireless Transmitter (XLR male connector)
• ACEMIC G6 Wireless Receiver (XLR female connector)
• USB Charging Cable (Type-C)
• User Manual

3. Product Overview

The ACEMIC G6 system consists of a transmitter and a receiver, both compact and designed for ease of use with dynamic microphones.

Key Features:

• 2.4GHz wireless frequency band, suitable for global coverage
• High quality audio sampling rate 24 bit/48kHz
• Frequency response range 20Hz-20kHz
• High signal-to-noise ratio reaches 110dB
• Audio transmission delay time less than 5 milliseconds
• 6 hours of battery life (rechargeable lithium battery)
• The use distance of the open space is greater than 30 meters
• Dynamic microphone for XLR interface

Components:

• Transmitter: Connects to your dynamic microphone. Features an XLR male connector, power button, and status indicator.
• Receiver: Connects to your audio input device (mixer, amplifier, speaker). Features an XLR female connector, power button, and status indicator.

4. Setup Instructions

Follow these steps to set up your ACEMIC G6 wireless microphone system:

1. Charge the Units: Before first use, fully charge both the transmitter and receiver using the provided USB charging cable. The indicator light will show charging status (e.g., red for charging, off or green for fully charged).
2. Connect Transmitter: Plug the ACEMIC G6 transmitter (XLR male) directly into the XLR output of your dynamic microphone. Ensure a secure connection.
3. Connect Receiver: Plug the ACEMIC G6 receiver (XLR female) into an available XLR input on your mixer, audio interface, amplifier, or powered speaker.
4. Power On: Press and hold the power button on both the transmitter and receiver until their respective indicator lights illuminate.
5. Pairing: The units should automatically pair. The indicator lights will typically change from a blinking state to a solid state once a connection is established. If they do not pair automatically, refer to the troubleshooting section.
6. Test Audio: Speak into the microphone and check the audio output from your connected sound system. Adjust volume levels on your mixer/amplifier as needed.

5. Operating Instructions

Power On/Off:

• To power on, press and hold the power button for approximately 2-3 seconds until the indicator light turns on.
• To power off, press and hold the power button for approximately 2-3 seconds until the indicator light turns off.

Indicator Lights:

The indicator lights provide information about the system's status:

• Blinking: Searching for connection or low battery.
• Solid: Connected and operating normally.
• Red (charging): Unit is charging.
• Off (charging): Unit is fully charged.

Operating Range:

The system operates effectively up to 30 meters (approximately 100 feet) in open, unobstructed spaces. Performance may vary in environments with significant obstacles or wireless interference.

Battery Life:

The built-in rechargeable lithium batteries provide up to 6 hours of continuous operation on a full charge. Actual battery life may vary based on usage and environmental conditions.

6. Maintenance

• Cleaning: Use a soft, dry cloth to clean the units. Do not use liquid cleaners or solvents.
• Storage: Store the system in a cool, dry place away from direct sunlight and extreme temperatures.
• Battery Care: To prolong battery life, avoid fully discharging the units frequently. Recharge them regularly, even if not in use for extended periods.
• Avoid Moisture: Keep the units away from water and high humidity to prevent damage.

7. Troubleshooting

• No Sound:
  • Ensure both transmitter and receiver are powered on and indicator lights are solid.
  • Check that the microphone is working and properly connected to the transmitter.
  • Verify the receiver is securely plugged into the audio input of your mixer/amplifier.
  • Check volume levels on your mixer/amplifier.
  • Ensure both units are charged.
• Intermittent Sound or Interference:
  • Move closer to the receiver to ensure you are within the operating range.
  • Check for other 2.4GHz devices (Wi-Fi routers, other wireless systems) that might be causing interference. Try to operate in a less congested area.
  • Ensure there are no large metal objects or walls obstructing the line of sight between the transmitter and receiver.
• Units Not Pairing:
  • Power off both units, then power them back on simultaneously.
  • Ensure they are within close proximity during the pairing process.
  • If issues persist, contact customer support.
• Short Battery Life:
  • Ensure units are fully charged before use.
  • Battery performance may degrade over time with extensive use.

8. Specifications

9. User Tips

No specific user tips were available from reviews or Q&A for this product at this time. General tips for wireless microphone systems include:

• Always fully charge your units before important events.
• Perform a sound check before live performances or recordings.
• Keep the transmitter and receiver in line of sight for optimal performance.
• Avoid placing the receiver near other wireless devices or large metal objects.

10. Warranty & Support

For warranty information and technical support, please refer to the seller's policies or contact the ACEMIC customer service directly. Keep your proof of purchase for any warranty claims.