AULA MINI 60HE PRO

Contents

AULA MINI 60HE PRO 8000hz Wireless Magnetic Shaft Mechanical Keyboard Instruction Manual

Model: MINI 60HE PRO

1. Introduction

This manual provides detailed instructions for the setup, operation, maintenance, and troubleshooting of your AULA MINI 60HE PRO 8000hz Wireless Magnetic Shaft Mechanical Keyboard. Please read this manual thoroughly before using the product to ensure optimal performance and longevity.

2. Product Features

  • High-performance three-mode magnetic shaft for precise control.
  • Ultra-low latency (0.1ms) and high return rate (8000Hz wired, 8000Hz wireless for Max version).
  • 0.01mm RT accuracy with zero dead zone for rapid response.
  • Three-mode connectivity: Wired (USB Type-C), Wireless 2.4G, and Bluetooth 5.0.
  • Hot-swappable keys for customization.
  • Built-in 4000mAh lithium battery (Pro/Max version) for extended use.
  • Multi-layer silencer structure for pure sound (Metal positioning board, Silencer cotton, Fiber shaft pad, Pet sound pad, PCB circuit board, Shaft cotton, Molded silicone bottom).
  • Support for online drivers for advanced functions.
  • 60% compact layout, freeing up desk space.
  • RGB backlight with approximately 16 million colors and over 20 preset lighting effects, supporting single-key customization.

3. Package Contents

Please check the package for the following items:

  • AULA MINI 60HE PRO Mechanical Keyboard
  • USB Type-C Cable
  • 2.4G Wireless Receiver
  • User Manual (this document)
  • Keycap Puller (may vary by package)
  • Switch Puller (may vary by package)

4. Setup Guide

4.1 Connectivity Modes

Your keyboard supports three connection modes: Wired, 2.4G Wireless, and Bluetooth. The mode switch is located on the side of the keyboard.

Keyboard connection modes diagram

Image: Diagram illustrating the three connection modes (Wired, 2.4G, Bluetooth) and the physical switch.

4.1.1 Wired Mode

  1. Ensure the mode switch on the keyboard is set to the middle position (wired mode).
  2. Connect the USB Type-C cable to the keyboard and your computer's USB port.
  3. The keyboard will be automatically recognized and ready for use.

4.1.2 2.4G Wireless Mode

  1. Set the mode switch on the keyboard to the left position (2.4G wireless mode).
  2. The key cyan light will flash slowly, indicating it's in pairing mode.
  3. Insert the 2.4G wireless receiver into a USB port on your computer.
  4. The keyboard should automatically connect. If not, refer to the factory default code matching instructions (usually involves pressing a specific key combination like Fn+P for a few seconds until the light changes).

4.1.3 Bluetooth Mode (BLE 5.0)

  1. Set the mode switch on the keyboard to the right position (Bluetooth mode).
  2. The blue indicator light will flash quickly, then slowly, indicating it's discoverable.
  3. On your device (computer, tablet, phone), search for Bluetooth devices and select "mini60he" (or "mini60hepro" for Pro version, "mini60hemax" for Max version).
  4. The blue light will turn solid after successful connection.
  5. To switch between up to 3 connected Bluetooth devices, use the Fn+W combination key. The blue light will flash quickly and then slowly, then turn solid blue for 2 seconds to indicate connection.

4.2 Driver Installation

The keyboard supports online drivers for advanced customization and functionality. Please visit the official AULA website to download and install the latest driver software for your operating system. This allows for key remapping, macro creation, and advanced lighting control.

Keyboard connected to computer with online driver support

Image: Keyboard connected to a computer, illustrating support for online driver software.

5. Operating Instructions

5.1 Backlight Control

The AULA MINI 60HE PRO features a vibrant RGB backlight with approximately 16 million colors and over 20 preset lighting effects. You can also customize individual key lighting.

RGB backlight effects on keyboard

Image: Keyboard displaying various RGB backlight effects.

  • Switching Effects: Use the Fn + combination keys to cycle through 19 different RGB lighting effects (e.g., flows gradually with waves, dynamic breathing, spectrum cycle). Specific key combinations will be detailed in the driver software.
  • Brightness/Speed Adjustment: Typically controlled via Fn + arrow keys or other designated function keys. Refer to the driver software for precise controls.
  • Single-Key Customization: Utilize the online driver software to program individual key colors and effects.

5.2 Energy-Saving Mode and Wake-Up

To conserve battery life, the keyboard enters various power-saving states.

Keyboard wake-up modes with red and green lights

Image: Keyboard showing red light for single-button wake-up and green light for full-key wake-up.

  • Power Saving Mode: If there is no operation for one minute in Bluetooth or 2.4G mode, the keyboard automatically enters power-saving mode.
  • Default Standby (Single-Key Wake-Up): Click the ESC key to wake up the keyboard. The ESC key will flash red.
  • Awake Mode (Full Key Wake-Up): To switch to awake mode, use the Fn+ESC combination key. When in awake mode, the ESC key flashes green light, and any key can wake the keyboard from hibernation.
  • Hibernation Mode: If the keyboard enters hibernation, any key can wake it up.
  • Sleep Mode: To wake from sleep mode, click the ESC key.

5.3 Magnetic Shaft Adjustment (0.01mm Accuracy)

The magnetic shafts allow for precise adjustment of the trigger and reset points, offering a 0.01mm adjustment accuracy. This feature is particularly beneficial for gaming, enabling faster key triggering and reset, and eliminating dead zones for emergency stops or rapid inputs.

Magnetic shaft adjustment accuracy diagram

Image: Diagram illustrating the 0.01mm adjustment accuracy of the magnetic shaft.

Adjustments are typically made through the online driver software, allowing users to fine-tune the actuation point to their preference.

6. Maintenance

6.1 Cleaning Your Keyboard

  • Keycaps: Use a keycap puller to carefully remove keycaps. Clean them with a soft cloth dampened with mild soap and water, then dry thoroughly before reattaching.
  • Keyboard Body: Use a soft, lint-free cloth to wipe down the keyboard surface. For stubborn dirt, a slightly damp cloth can be used. Ensure no liquid enters the keyboard.
  • Between Keys: Use compressed air to remove dust and debris from between the keys. A small brush can also be used.

Caution: Do not use harsh chemicals, abrasive cleaners, or excessive moisture, as these can damage the keyboard's finish or internal components.

6.2 Battery Care

  • To prolong battery life, avoid fully discharging the keyboard frequently.
  • Charge the keyboard using the provided USB Type-C cable connected to a standard USB power source.
  • Store the keyboard in a cool, dry place when not in use for extended periods.

7. Troubleshooting

7.1 Connection Issues

  • Wired Connection Not Working:
    • Ensure the USB Type-C cable is securely connected to both the keyboard and the computer.
    • Try a different USB port on your computer.
    • Test with a different USB Type-C cable if available.
    • Verify the mode switch is in the middle (wired) position.
  • 2.4G Wireless Not Connecting:
    • Ensure the mode switch is in the left (2.4G) position.
    • Make sure the 2.4G receiver is properly inserted into a USB port.
    • Try re-pairing the keyboard with the receiver (refer to section 4.1.2).
    • Ensure there are no strong interferences (e.g., other wireless devices) nearby.
  • Bluetooth Not Pairing/Connecting:
    • Ensure the mode switch is in the right (Bluetooth) position.
    • Verify Bluetooth is enabled on your device.
    • Remove any previous pairings of the keyboard from your device's Bluetooth settings and try pairing again.
    • Ensure the keyboard is discoverable (blue light flashing).
    • Try connecting to a different Bluetooth channel (Fn+W).

7.2 Keys Not Responding / Double Input

  • Ensure the keyboard is fully charged or connected via wired mode.
  • Check for debris under the keycap. Carefully remove the keycap and clean the switch area.
  • If using magnetic switches, recalibrate or adjust the actuation point using the driver software.
  • If hot-swappable switches are installed, ensure they are seated correctly.

7.3 Backlight Issues

  • Ensure the backlight is not turned off or set to minimum brightness.
  • Check backlight settings in the driver software.
  • If only certain keys are affected, it might indicate a hardware issue.

8. Specifications

Product specifications table

Image: Table summarizing key product specifications.

FeatureDescription
Model NameWolf spider mini60he three-mode magnetic axis keyboard
Keyboard Standard61 Keys (60% layout)
Operation StyleMechanical (Magnetic Shaft)
Switches Hot SwapYes
Switches ManufacturerGATERON (and others like Fengyun, Smoke Cloud, Lingyun magnetic shafts)
Keycup MaterialPBT plastic
Keycup PrintingDye-sublimation, OEM, MDA gradient, high-line translucent
Backlight TypeMULTICOLOR (RGB)
Connection MethodWired (USB Type-C), 2.4Ghz Wireless, Bluetooth 5.0
Interface TypeUSB
Return RateWired: 8000Hz (Standard/Pro/Max), Wireless: 8000Hz (Max version)
Scan RateUp to 128KHz
Accuracy0.01mm RT accuracy
BatteryBuilt-in 4000mAh Lithium Battery (Pro/Max version), 3000mAh (Standard version)
Battery Life (approx.)About 45 hours (lights off); Other 3-mode magnetic shaft keyboards: ~25 hours (lights off)
Dimensions (L x W x H)299.04mm x 102.16mm x 37.09mm (±1mm)
Weight~622g (excluding wire/receiver), ~669g (including wire/receiver)
Ergonomics SupportYes
CertificationCE

Note: Specifications are based on available product information and may vary slightly. The structural diagram is for reference only; the actual product shall prevail.

Magnetic switch specifications for Fengyun, Smoke Cloud, and Lingyun

Image: Detailed specifications for Fengyun, Smoke Cloud, and Lingyun magnetic switches, including initial pressure, stroke, and magnetic pass.

9. User Tips

  • Optimize Actuation: Experiment with the magnetic shaft adjustment via the online driver to find your preferred actuation point for different games or typing tasks. A lower actuation point can provide faster response for gaming.
  • Battery Management: Utilize the energy-saving modes effectively, especially when using wireless connections, to maximize battery life. Remember to fully charge the keyboard before long gaming sessions.
  • Customization: Take advantage of the hot-swappable switches to try different switch types if you desire a different typing feel or sound. The online driver also offers extensive customization for RGB lighting and key functions.
  • Firmware Updates: Regularly check the official AULA website for firmware updates, which can improve performance, add new features, or fix bugs.

10. Warranty and Support

AULA products are designed for quality and performance. For warranty information, technical support, or service inquiries, please refer to the official AULA website or contact your retailer. Keep your proof of purchase for warranty claims.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.