1. Introduction
This manual provides comprehensive instructions for the Estardyn 1.47-inch TFT LCD screen module. This compact display features a high-resolution color screen, driven by the ST7789 IC, and communicates via a 4-wire SPI interface. It is designed for integration into various embedded systems and DIY electronics projects. Please read this manual thoroughly before use to ensure proper setup and operation.

2. Specifications
The following table details the technical specifications of the Estardyn 1.47-inch TFT LCD module:
| Feature | Specification |
|---|---|
| Brand Name | Estardyn |
| Model Number | 1.47-inch TFT |
| Type | TFT |
| Display Size | 1.47 inch |
| Resolution | 172x320 pixels |
| Display Color | Colorful |
| Driver IC | ST7789P3 |
| Interface Type | 4-wire SPI |
| Power Supply | 2.8V ~ 3.3V |
| Working Temperature | -20°C ~ 70°C |
| Linking Method | 8-pin |
| Screen Size (mm) | 19.39 * 36.28 * 1.559 |
| Module Size (mm) | 20.96 * 44 * 2.76 |
| Display Area (mm) | 17.39 * 32.35 |
| Origin | Mainland China |

3. Pin Definition
The module features an 8-pin interface for connection to a microcontroller or other host device. The pin assignments are as follows:
| PIN | SYMBOL | Description |
|---|---|---|
| 1 | GND | Ground |
| 2 | VDD | Power Supply (2.8V-3.3V) |
| 3 | SCL | Serial Clock (SPI) |
| 4 | SDA | Serial Data (SPI) |
| 5 | RES | Reset Pin |
| 6 | DC | Data/Command Selection |
| 7 | CS | Chip Select (SPI) |
| 8 | BL | Backlight Control |


4. Setup and Connection
To set up your Estardyn 1.47-inch TFT LCD module, follow these steps:
- Power Supply: Connect the VDD pin to a 2.8V to 3.3V power source and the GND pin to the ground of your microcontroller. Ensure the power supply is stable and within the specified voltage range.
- SPI Interface: Connect the SCL, SDA, RES, DC, and CS pins to the corresponding SPI pins on your microcontroller. Refer to your microcontroller's datasheet for specific pin assignments.
- SCL (Serial Clock): Connect to the SPI clock pin (e.g., SCK on Arduino).
- SDA (Serial Data): Connect to the SPI data pin (e.g., MOSI on Arduino).
- RES (Reset): Connect to a digital output pin on your microcontroller. This pin is used to reset the display.
- DC (Data/Command): Connect to a digital output pin on your microcontroller. This pin determines whether the data being sent is a command or display data.
- CS (Chip Select): Connect to a digital output pin on your microcontroller. This pin enables or disables communication with the display.
- Backlight Control: Connect the BL pin to a digital output pin or a PWM-capable pin on your microcontroller if you wish to control the backlight brightness. If constant backlight is desired, connect BL to VDD (through a current-limiting resistor if necessary, though often not required for modules with integrated resistors).
- Software Library: Install a compatible ST7789 driver library for your chosen microcontroller platform (e.g., Adafruit GFX and Adafruit ST7789 libraries for Arduino).
- Initialization: Use the provided library functions to initialize the display, set the orientation, and begin drawing graphics.
5. Basic Operation
Once the module is correctly wired and the necessary software libraries are installed, you can begin operating the display:
- Initialization: Call the display's `begin()` function (or equivalent) in your code to power up the display and configure the ST7789 driver.
- Drawing Primitives: Use library functions to draw pixels, lines, rectangles, circles, and other shapes. Specify coordinates and colors for each element.
- Text Display: Set the text size, color, and font, then use text drawing functions to display characters and strings on the screen.
- Image Display: For displaying images, convert your image data into a format compatible with the display library (e.g., a byte array) and use the appropriate drawing functions.
- Screen Refresh: Many libraries handle screen refreshing automatically. For direct control, ensure you understand how to update the display buffer and push it to the screen.
- Backlight Control: Adjust the backlight by setting the state of the BL pin (HIGH for ON, LOW for OFF) or by using PWM for brightness control if connected to a PWM pin.
6. Maintenance and Care
To ensure the longevity and optimal performance of your LCD module, follow these maintenance guidelines:
- Handling: Always handle the module by its edges. Avoid touching the display surface directly to prevent fingerprints, scratches, or damage.
- Cleaning: If the screen surface becomes dirty, gently wipe it with a soft, lint-free cloth. For stubborn marks, slightly dampen the cloth with distilled water or a specialized screen cleaner. Do not use abrasive cleaners, solvents, or excessive moisture.
- Storage: Store the module in a dry, dust-free environment, away from direct sunlight and extreme temperatures. Use anti-static packaging if available.
- Power: Ensure the power supply voltage is within the specified range (2.8V-3.3V). Over-voltage can permanently damage the module.
- ESD Protection: Take precautions against electrostatic discharge (ESD) when handling the module, as static electricity can damage sensitive electronic components.
7. Troubleshooting
If you encounter issues with your LCD module, consider the following troubleshooting steps:
- No Display/Blank Screen:
- Verify all power connections (VDD, GND) are correct and stable.
- Check the backlight (BL) pin connection. Ensure it's receiving power or being controlled correctly.
- Confirm the RES (Reset) pin is toggled correctly during initialization.
- Double-check all SPI connections (SCL, SDA, DC, CS) for continuity and correct pin assignment.
- Ensure the correct display driver library (ST7789) is installed and initialized with the correct pin definitions in your code.
- Garbled or Incorrect Display:
- Check the SPI communication speed. Some microcontrollers might require specific clock dividers for stable SPI communication with the display.
- Verify the display initialization sequence in your code matches the requirements of the ST7789 driver.
- Ensure the data format (e.g., color depth, byte order) used in your drawing functions matches the display's expectations.
- Confirm the display orientation settings in your code are correct.
- Partial Display or Missing Pixels:
- This could indicate a loose connection on the flexible flat cable (FFC) connecting the LCD panel to the PCB. Handle with care.
- Check for any physical damage to the screen or PCB.
- Backlight Not Working:
- Ensure the BL pin is connected and receiving power (VDD) or a HIGH signal from your microcontroller.
- If using PWM, verify the PWM signal is correctly generated and connected.
8. User Tips
- Voltage Level Shifters: If your microcontroller operates at 5V (e.g., some Arduino boards), consider using a logic level shifter for the data pins (SCL, SDA, RES, DC, CS, BL) to protect the 3.3V tolerant display module.
- Library Compatibility: When using third-party libraries, always check for compatibility with the ST7789 driver and your specific microcontroller. Examples and community forums can be very helpful.
- Power Consumption: While compact, color LCDs can consume a noticeable amount of power, especially with the backlight on. Factor this into your project's power budget.
9. Warranty and Support
For any issues not covered in this manual or for technical support, please contact the seller or manufacturer directly. Keep your purchase records for warranty claims. This product is intended for hobbyist and professional use in electronic projects.