1. Product Overview
This manual provides instructions for the replacement water tank, dust box, and filter accessories designed for the 360 S8 Robotic Vacuum Cleaner. These components are crucial for maintaining the vacuum cleaner's optimal performance in both dry vacuuming and wet mopping functions.
Figure 1: Combined Water Tank and Dust Box with Filter
Figure 2: Top view of the Water Tank Dust Box
2. Setup and Installation
Before installing new components, ensure your 360 S8 Robotic Vacuum Cleaner is powered off and disconnected from its charging base.
2.1 Installing the Dust Box and Filter
- Locate the dust box compartment on your 360 S8 robotic vacuum cleaner.
- Press the release button or tab to open and remove the old dust box.
- If replacing only the filter, open the filter cover on the dust box (refer to Figure 3) and remove the old filter. Insert the new filter, ensuring it sits flush within the compartment. Close the filter cover securely.
- Insert the new dust box (with filter installed) into the vacuum cleaner until it clicks into place.
Figure 3: Dust Box with Filter Compartment Open
2.2 Installing the Water Tank
- Locate the water tank compartment on your 360 S8 robotic vacuum cleaner.
- Press the release button or tab to open and remove the old water tank.
- Open the water tank cap, fill it with clean water (do not use detergents or harsh chemicals unless specified by the vacuum cleaner's original manual), and securely close the cap.
- Insert the new water tank into the vacuum cleaner until it clicks into place.
Figure 4: Side view of the Water Tank
3. Operating Instructions
These accessories function as integral parts of your 360 S8 Robotic Vacuum Cleaner. Their operation is controlled by the vacuum cleaner's main system.
- Dust Box: Collects dust, debris, and pet hair during dry vacuuming cycles.
- Filter: Traps fine dust particles and allergens, ensuring cleaner air is expelled from the vacuum.
- Water Tank: Supplies water to the mopping pad (if applicable) for wet cleaning functions. Ensure it is filled before starting a mopping cycle.
Refer to your 360 S8 Robotic Vacuum Cleaner's main user manual for detailed instructions on initiating cleaning cycles, setting schedules, and selecting cleaning modes.
4. Maintenance
Regular cleaning and replacement of these accessories are essential to maintain the cleaning efficiency and longevity of your 360 S8 Robotic Vacuum Cleaner.
4.1 Dust Box Maintenance
- Emptying: After each cleaning cycle, or when the dust box full indicator appears, remove the dust box from the vacuum cleaner. Open the lid and empty the collected debris into a trash bin.
- Cleaning: Periodically, rinse the dust box with clean water. Ensure it is completely dry before re-installing it into the vacuum cleaner. Do not wash the filter with water unless it is specifically stated as washable.
4.2 Filter Maintenance
- Cleaning: Tap the filter gently over a trash can to remove loose dust and debris. A small brush can be used to clean between the pleats.
- Replacement: Filters should be replaced regularly, typically every 1-3 months, depending on usage and environment. A dirty filter can reduce suction power and cleaning effectiveness.
4.3 Water Tank Maintenance
- Emptying: After each mopping cycle, empty any remaining water from the tank to prevent stagnant water and potential odors.
- Cleaning: Rinse the water tank with clean water. If mineral deposits build up, a mild descaling solution (e.g., diluted vinegar) can be used, followed by thorough rinsing.
- Drying: Allow the water tank to air dry completely before storing or refilling.
5. Troubleshooting
If you experience issues with your 360 S8 Robotic Vacuum Cleaner after installing these replacement parts, consider the following:
- Reduced Suction Power: Check if the dust box is full or if the filter is clogged. Clean or replace the filter as necessary. Ensure the dust box is correctly seated.
- No Water Dispensing (Mopping): Verify the water tank is filled and correctly installed. Check for any blockages in the water outlet.
- Unusual Noises: Ensure all components (dust box, water tank) are securely installed and no foreign objects are trapped within the compartments.
- Part Not Fitting: Double-check that you have the correct replacement parts for the 360 S8 model. Ensure no debris is obstructing the installation path.
For persistent issues, refer to the original 360 S8 Robotic Vacuum Cleaner user manual or contact the manufacturer's support.
6. Specifications
| Attribute | Value |
|---|---|
| Vacuum Part Type | Filters (and associated components) |
| Model Number | For 360 S8 Water Tank Dust Box Parts Vacuum Cleaner Robotic Robot Dust |
| Type | Vacuum Cleaner Parts |
| Origin | Mainland China |
| Package Length | 24 cm |
| Package Width | 13 cm |
| Package Height | 17 cm |
| Package Weight | 0.463 kg |
7. User Tips
No specific user tips were available from the provided data. However, general best practices for robotic vacuum cleaner accessories include:
- Always use clean, filtered water in the water tank to prevent mineral buildup and clogs.
- For optimal performance, clean the dust box and filter after every 1-3 cleaning cycles, especially if you have pets or a high-traffic home.
- Keep spare filters on hand to ensure timely replacement and consistent air filtration.
8. Warranty and Support
These replacement parts are designed for the 360 S8 Robotic Vacuum Cleaner. For warranty information regarding the original vacuum cleaner or these specific replacement parts, please refer to the documentation provided with your 360 S8 Robotic Vacuum Cleaner or contact the original seller/manufacturer directly.
Please note that seller policies may include options such as free returns within a specified period. Always verify such policies with your point of purchase.
