1. Introduction
The JIKONG Smart BMS (Battery Management System) is an intelligent active balance power management system designed for Li-ion, LiFePo4, and LTO battery packs ranging from 4S to 24S. This BMS ensures optimal battery performance and longevity through advanced active balancing technology.
Active balancing, also known as non-lossy balancing, efficiently transfers energy from cells with higher energy to those with lower energy. This process achieves voltage balance with minimal energy loss and operates continuously during charging, discharging, or idle states until the voltage difference is within a set range. Unlike passive balancing, active balancing can utilize larger currents (typically 1-2A) without generating excessive heat, making it ideal for larger capacity battery packs.
Key features of the JIKONG Smart BMS include a multi-interface display, support for major communication interfaces like GPS, RS485, CAN, and NTC temperature sensors, a high-performance MCU, and a durable full aluminum alloy shell for excellent heat dissipation. It supports continuous currents of 40A-80A and instantaneous currents of 200A-450A.



2. Setup Instructions
2.1. Packing List
Before installation, ensure all components are present:
- BMS x 1
- Switch x 1 (long 50cm)
- NTC x 1 (long 40cm)
- Sampling line B x 1 (long 70cm)
- Sampling line A x 1 (long 70cm)

2.2. Installation and Wiring
Follow these steps for proper installation and wiring:
- Connect all necessary cables to the battery cells.
- Insert the balance cables into the designated ports on the BMS.
- Connect the B-line (total negative electrode) and P-line (total positive electrode) to the battery pack.

2.3. Wiring Diagrams
Refer to the following diagrams for specific cell configurations:


2.4. Interface Details
The BMS features rich interfaces for various functionalities:
- GPS (customized): For location-based services.
- CAN (customized): For CAN bus communication.
- RS485 (customized): For RS485 communication.
- NTC: For temperature sensing.
- Heat (customized): For heating control.
- Sampling port B & A: For cell voltage sampling.
- Display / Switch Key: For external display and control.

3. Operating Instructions
3.1. Multi-Screen Display and Data Connection
The JIKONG Smart BMS supports multi-screen display and data connection via a mobile app (iOS, Android, HarmonyOS) or PC software. This allows you to view real-time information such as voltage, current, temperature, State of Charge (SOC), and cycle count at a glance.

3.2. Intelligent Interaction and Parameter Adjustment
The system allows for free adjustment of multiple protection values, including overcharge, overdischarge, overcurrent, temperature, and balance parameters. To adjust parameters, first read the internal parameters of the protection board, and then make the desired changes through the mobile app or PC software.

3.3. Protocol Docking
The JIKONG Smart BMS is compatible with mainstream inverter communication protocols in the market. You can easily set up and select supported CAN protocols through the mobile app or host computer software.

4. Maintenance
To ensure the longevity and optimal performance of your JIKONG Smart BMS, consider the following maintenance tips:
- Regularly check all wiring connections to ensure they are secure and free from corrosion.
- Keep the BMS unit clean and free from dust and debris.
- Ensure adequate ventilation around the BMS to facilitate heat dissipation, especially during high current operation. The full aluminum alloy shell provides superior heat dissipation, but proper airflow is still beneficial.
- Avoid exposing the BMS to extreme temperatures or humidity.

5. Troubleshooting
If you encounter issues with your JIKONG Smart BMS, consider the following general troubleshooting steps:
- No Power/No Display: Verify all power connections (B-line, P-line) are correctly wired and secured. Check the battery voltage.
- Balancing Issues: Ensure all sampling lines are correctly connected to each cell. Check for any loose connections or damaged wires. Review the balancing current settings in the app/software.
- Communication Problems (Bluetooth/RS485/CAN): Ensure the app is updated to the latest version. Check physical connections for RS485/CAN. For Bluetooth, ensure the BMS is powered on and within range.
- Overcharge/Overdischarge Protection Triggered: Check individual cell voltages. Adjust protection parameters in the app/software if necessary, but always ensure they are within safe limits for your battery chemistry.
- Overcurrent/Short Circuit Protection Triggered: Disconnect the load and inspect for any short circuits in the system. Reduce the load if it exceeds the BMS's continuous or instantaneous current ratings.
For persistent issues, consult the detailed error logs available through the app or PC software, which can provide specific diagnostic information.
6. Specifications
The JIKONG Smart BMS offers robust specifications for various battery applications. Below is a summary of key product parameters and general properties.
6.1. Product Parameters

6.2. General Properties
| Attribute | Value |
|---|---|
| Model Number | JK-BD6A17S6P/JK-BD6A20S6P/JK-BD6A24S6P |
| Accessory Type | Battery Accessories |
| Type | LIFEPO4 Battery BMS |
| Balance Function | Active Balanced BMS |
| Charge and Discharge Port | Common Port BMS |
| Function | Overcharge Protection, Over Discharge Protection, Overcurrent Protection, Short Circuit Protection |
| Voltage range | USB (5-20V DC) |
| Charging Current | 60A |
| Electronic | No |
| Charger included | No |
| Battery Included | No |
| High-concerned chemical | None |
| Origin | Mainland China |
| Certification | CE |
7. User Tips
- Always double-check your wiring connections, especially the balance leads, before powering on the BMS to prevent damage.
- Utilize the mobile app or PC software for real-time monitoring and fine-tuning of parameters to optimize your battery pack's performance.
- When adjusting parameters, make small, incremental changes and observe the system's behavior to ensure stability.
- For long-term storage, ensure the battery pack is balanced and stored at an appropriate State of Charge (SOC) as recommended by your battery manufacturer.
8. Warranty and Support
For warranty information, technical support, or service inquiries, please contact the JIKONG BMS FACTORY Store directly through the platform where the product was purchased. Ensure you have your product model number and purchase details ready for faster assistance.