SAGE LU MEI C4

Contents

SKYDANCE C4 Push Dim Dimmer LED Controller User Manual

Model: C4 | Brand: SAGE LU MEI

1. Introduction

The SKYDANCE C4 Push Dim Dimmer LED Controller is a versatile 4-channel constant current LED controller designed for single color, dual color, RGB, and RGBW LED lamps. It features RF 2.4G wireless control, push dimming functionality, and supports multiple output current settings (150-500mA or 350-1200mA). The controller offers 4096 levels of smooth dimming, built-in dynamic modes for RGB/RGBW lights, auto-transmitting, and synchronization capabilities. This manual provides detailed instructions for safe and effective use of your C4 LED controller.

2. Safety & Warnings

Read all instructions before use to ensure safety and prevent damage.

  • Warning: Keep the device and its cord out of reach of children under 3 years old.
  • Ensure the input voltage (12-48VDC) matches the power supply.
  • Do not expose the device to moisture or extreme temperatures.
  • All electrical connections should be performed by a qualified professional.
  • Disconnect power before any installation or maintenance.

3. Package Contents

Your package should contain the following:

  • 1 x SKYDANCE C4 Push Dim Dimmer LED Controller (150-500mA or 350-1200mA version, as chosen)

Note: Remote control and power supply are sold separately.

4. Technical Specifications

Technical Specifications Table for C4 LED Controller

Figure 1: Technical Specifications Table

C4 LED Controller Specifications
Attribute Value
Model Number C4
Features RGBW/RGB/CCT/Dimming 4 Channel LED RF Controller
Connection Mode RF 2.4GHz + Push Dim
Certification CE, ROHS
Voltage 12-48VDC
Material ABS
Output Current (Wattage) 4CH*(150-500mA) or 4CH*(350-1200mA)
Max. Load Power 4 x (0.45-22.5)W (150-500mA) or 4 x (1.05-54)W (350-1200mA)
Power Source DC
Remote Distance 30m (Barrier-free space)
Applicable Lights Single color/dual color/RGB/RGBW LED lamp
Controlled Method 2.4G single color/dual color/RGB/RGBW remote control
Operation Temperature Ta: -30°C ~ +55°C
Case Temperature (Max.) Tc: +85°C
IP Rating IP20

5. Installation and Setup

5.1 Mechanical Structures and Connections

The C4 controller features input terminals for 12-48VDC power and output terminals for connecting to LED lights. It also includes a match key, DIP switches for current and light type selection, and terminals for a push switch.

Mechanical Structure and LED Current Selection Diagram

Figure 2: Mechanical Structure and LED Current Selection

5.2 LED Current Selection

Before powering on, select the correct output current for your LED lights using the DIP switches on the PCB board. Refer to Figure 2 for the DIP switch configuration tables for both 150-500mA and 350-1200mA versions.

Note: Please select the correct current through the DIP switch on the PCB board when the power is off.

5.3 Wiring Diagrams

Ensure all wiring is done correctly according to the diagrams below. The controller works on buck mode, meaning the voltage of the power supply should be greater than the total voltage of the series LEDs.

Wiring Diagram for RGBW and RGB LED Controllers

Figure 3: Wiring Diagram for RGBW and RGB

Wiring Diagram for Dual Color and Single Color LED Controllers

Figure 4: Wiring Diagram for Dual Color and Single Color

Note:

  1. The LED quantity at each channel can be different; the controller will auto check and output a proper voltage to each channel according to its LED quantities.
  2. The controller works on buck mode, the voltage of power supply should be greater than the total voltage of the series LEDs.

6. Operating Instructions

6.1 Light Type Selection (DIP Switch)

The C4 controller can be configured for single color, dual color, RGB, or RGBW operation using the DIP switches. Refer to the 'Light Type Select' section on the controller (visible in Figure 2) and consult the product documentation for specific switch settings for each light type.

6.2 Push Dim Function

The controller supports an external push switch for on/off and 0-100% dimming functionality. The operation varies based on the light type:

Push Dim Operation Table and Dimming Curves

Figure 5: Push Dim Operation and Dimming Curves

Push Dim Functionality
Light Type Action Function
Single Color Click ON/OFF
Double Click Turn on at 100% or 10% (night light) and vice-versa
Long press (>1s) from OFF Dimming UP/DOWN
Dual Color Click ON/OFF
Double Click Turn on at 100% or 10% (night light) and vice-versa
Long press (>1s) from ON Color temperature UP/DOWN (turn off and turn on to return dimming)
RGB Click Change from color mode to white mode (RGB mixed) and vice-versa
Long press (>1s) from OFF If on color mode change rotation speed; if on white mode dimming UP/DOWN
Long press (>1s) from ON If on color mode start/stop color rotation; if on white mode dimming UP/DOWN
RGBW Click ON/OFF
Double Click Change between color mode, white mode ('W' channel) and color+W mode
Long press (>1s) from OFF If on color mode change rotation speed; if on white mode or color+W mode, dimming UP/DOWN

6.3 Remote Control Matching

The C4 controller can be matched with RF 2.4G single zone or multiple zone remote controls. There are two methods for matching/deleting remotes:

Remote Control Matching Instructions and Dynamic Mode List

Figure 6: Remote Control Matching and Dynamic Modes

Method 1: Use the controller's Match key

  • Match: Short press the match key, then immediately press the on/off key (single zone remote) or zone key (multiple zone remote) 3 times on the remote. The LED indicator will flash a few times, indicating a successful match.
  • Delete: Press and hold the match key for 5 seconds to delete all matched remotes. The LED indicator will flash a few times.

Method 2: Use Power Restart

  • Match: Switch off the power, then switch on power again. Immediately short press the on/off key (single zone remote) or zone key (multiple zone remote) 3 times on the remote. The light will blink 3 times, meaning the match is successful.
  • Delete: Switch off the power, then switch on power again. Immediately short press the on/off key (single zone remote) or zone key (multiple zone remote) 5 times on the remote. The light will blink 5 times, meaning all matched remotes were deleted.

6.4 RGB/RGBW Dynamic Modes

When using with RGB/RGBW lights, the controller has 10 built-in dynamic modes, including jump or gradual change styles. Refer to Figure 6 for the list of dynamic modes.

Fade In and Fade Out Setting

  • Long press the match key for 5 seconds, then short press the match key 3 times. The lighting effect will be set to fade in and fade out in 3 seconds. The indicator light of the LED controller blinks 3 times.
  • Long press the match key for 10 seconds to restore factory default parameters. The light on/off time restores to 0.5 seconds.

Color Rotation Speed

For RGB/RGBW color rotation, you can select 4 rotation speeds:

  • 10 flash/s means 6 seconds color rotation
  • 5 flash/s means 30 seconds color rotation
  • 2 flash/s means 1 minute color rotation
  • 1 flash/s means 6 minutes color rotation

7. User Tips

  • Always double-check the DIP switch settings for both LED current and light type before applying power to prevent damage to your LEDs or controller.
  • For optimal RF remote control performance, ensure the controller is not obstructed by large metal objects.
  • When using the Push Dim function, a momentary switch (bell press switch) is typically required for proper operation.
  • Consider using a multimeter to verify output current and voltage during initial setup to ensure compatibility with your LED fixtures.

8. Maintenance

  • Keep the controller clean and free from dust. Use a dry, soft cloth for cleaning.
  • Do not use harsh chemicals or abrasive cleaners.
  • Ensure adequate ventilation around the controller to prevent overheating.
  • Periodically check all wiring connections for tightness and signs of wear.

9. Troubleshooting

Common Issues and Solutions
Problem Possible Cause Solution
LEDs not lighting up
  • No power to controller
  • Incorrect wiring
  • Incorrect DIP switch settings for current/light type
  • Faulty LEDs or power supply
  • Check power connections and supply voltage.
  • Verify wiring against diagrams (Figures 3 & 4).
  • Ensure DIP switches are set correctly for your LEDs (Figure 2).
  • Test LEDs and power supply independently.
Remote control not working
  • Remote not matched
  • Remote battery low/dead
  • Interference
  • Re-match the remote control (Section 6.3).
  • Replace remote battery.
  • Ensure clear line of sight or reduce interference sources.
Dimming is not smooth or flickers
  • Incompatible LED driver/fixture
  • Power supply issues
  • Ensure LEDs are compatible with constant current dimming.
  • Check power supply stability.

10. Warranty and Support

For technical support or warranty inquiries, please contact the manufacturer or their authorized representative:

Manufacturer Information:

  • Company: Shenzhen shengluomei technology co., ltd
  • Address: No. 205 no. 6, lane 2, wuh iro community, sakata street, longgang district, shenzhen city, guangdong province
  • Phone: 86-15914360896
  • Email: 821880792@qq.com

EU Authorized Representative:

  • Company: Apex CE Specialists GmbH
  • Address: Grafenberger Allee 277, 40237 Düsseldorf, DE
  • Phone: 49-1776995991
  • Email: Info@apex-ce.de

For additional information, you may refer to the official user manual PDF: View User Manual (PDF)

© 2023 SAGE LU MEI. All rights reserved.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.