9IMOD F722 Flight Stack

Contents

9IMOD F722 Flight Stack User Manual

F722 Flight Control & 55A/60A ESC for RC FPV Racing Drones

1. Introduction

The 9IMOD F722 Flight Stack is a high-performance integrated solution designed for RC FPV Racing Drones. It combines an F722 Flight Controller with either a 55A or 60A Electronic Speed Controller (ESC), offering robust control and power delivery. This flight stack supports open-source Betaflight firmware and Bluejay firmware for the ESC, enabling advanced customization and flight characteristics. Its design features large solder pads for ease of assembly and includes essential components like an OSD module and barometer for comprehensive flight data.

9IMOD F722 Flight Stack product image

Figure 1: 9IMOD F722 Flight Stack

2. Safety Information

⚠ WARNING: This product can expose you to chemicals including phthalates (DEHP), which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.

Always exercise caution when working with electronic components, especially those involving high current and voltage. Ensure proper insulation and secure connections to prevent short circuits. Disconnect power before making any changes or repairs. This product is intended for experienced users in the RC hobby.

3. Package Contents

Please verify that all items are present in your package. Contents may vary slightly based on the specific variant purchased (55A ESC or 60A ESC).

3.1 F722 Flight Control + 55A ESC Variant

  • F722 Flight Controller: 1 unit
  • 55A ESC: 1 unit
  • Package Box: 1 unit
  • TS100 GPS Connect Cable: 1 unit
  • R8SM Receiver Connect Cable: 1 unit
  • Camera Connect Cable: 1 unit
  • Power cable + XT60: 1 unit
  • Silicone vibration absorber: 8 units
  • Screw: 4 units
  • Hex nut: 4 units
  • ESC Connect Cable: 1 unit
  • Analog Video Transmission Connect Cable: 1 unit
  • ELRS Receiver Connect Cable: 1 unit
  • Low ESR capacitor: 1 unit
Package contents for F722 Flight Control with 55A ESC

Figure 2: Package Contents (55A ESC variant)

3.2 F722 Flight Control + 60A ESC Variant

  • F722 Flight Controller: 1 unit
  • 60A ESC: 1 unit
  • Package Box: 1 unit
  • TS100 GPS Connect Cable: 1 unit
  • R8SM Receiver Connect Cable: 1 unit
  • Camera Connect Cable: 1 unit
  • Power cable + XT60: 1 unit
  • Silicone vibration absorber: 8 units
  • Screw: 4 units
  • Hex nut: 4 units
  • ESC Connect Cable: 2 units
  • Analog Video Transmission Connect Cable: 1 unit
  • ELRS Receiver Connect Cable: 1 unit
  • Low ESR capacitor: 1 unit
Package contents for F722 Flight Control with 60A ESC

Figure 3: Package Contents (60A ESC variant)

4. Specifications

4.1 F722 Flight Control Parameters

FeatureSpecification
Master chipSTM32F722RET6
GyroscopeICM42688
Battery Input3-8S Lipo
USB PortType-C
BarometerBMP280
OSD chipAT7456E
BluetoothNot Supported
RSSISupport (marked as RSSI)
Supported FC FirmwareBetaflight
Firmware NameDAKEFPVF722
Installation Hole Position30.5x30.5mm/M4
Size36mm x 36mm x 8mm
Weight (Bare board)8g
iNav SupportYes
Ardupilot SupportNo
DJI O4 ConnectionAllows connection
GPS ModuleRequires ubbox protocol support
F722 Flight Control Parameter Table

Figure 4: F722 Flight Control Parameters

4.2 55A ESC Parameters

FeatureSpecification
MCUEFM8BB21F16G-C-QFN20R
Continuous Current55A x 4
Transient Current60A (10S)
ProgramBlueJay
MOS3109
TVS Protection DiodeYes
Electrolytic Capacitor1000uF Low ESR Capacitor
Motor ProtocolDshot300/600
Battery Input3-6S Lipo
AmmeterSupport
Power OutputVBAT
Installation Hole Position30.5x30.5mm/M4
SizeLength 43mm x 37mm x 7mm
Weight (Bare board)12g
55A ESC Parameter Table

Figure 5: 55A ESC Parameters

4.3 60A ESC Parameters

FeatureSpecification
MCUEFM8BB21F16G-C-QFN20R
Continuous Current60A x 4
Transient Current65A (10S)
ProgramBlueJay
MOS5C430
TVS Protection DiodeYes
Electrolytic Capacitor1000uF Low ESR Capacitor
Motor ProtocolDshot300/600
Battery Input3-8S Lipo
AmmeterSupport
Power OutputVBAT
Installation Hole Position30.5x30.5mm/M4
SizeLength 43mm x 37mm x 7mm
Weight (Bare board)12g
60A ESC Parameter Table

Figure 6: 60A ESC Parameters

4.4 2.4G Receiver Specifications

FeatureSpecification
TypeISM, ESP8285 MCU
RF ModuleSX1280IMLTRT
AntennaOmnidirectional
Frequency Range2400 MHz to 2500 MHz
Max Receive Refresh Rate500Hz
Min Receiver Refresh Rate25Hz
Working Voltage5V
Weight (without antenna)0.8g
Peak Gain2.23dB

5. Setup and Wiring

The F722 Flight Stack is designed for straightforward integration into your FPV drone. Refer to the wiring diagrams below for proper connection of components. The large solder pads are designed to assist beginners with soldering.

5.1 General Wiring Diagram

General wiring diagram for F722 Flight Stack

Figure 7: General Wiring Diagram

5.2 Full Socket Version Wiring Diagram

This diagram illustrates connections for various peripherals including VTX, GPS, Camera, ESC, and Crossfire Nano Receiver.

F722 Full Socket Version wiring diagram with VTX, GPS, Camera, ESC, Crossfire Nano Rx

Figure 8: Full Socket Version Wiring Diagram

Note for DJI Digital Image Transmission: If you intend to use DJI Digital Image Transmission with SBUS control protocol, you must short-circuit the designated solder pad jumper on the flight controller.

5.3 Motor and Peripheral Wiring

This diagram provides a detailed view of motor connections and other common peripherals like LEDs, Buzzer, and SBUS Receiver.

F722 Full Socket Version wiring diagram with motors and peripherals

Figure 9: Motor and Peripheral Wiring

5.4 Firmware Flashing and Configuration

The F722 Flight Controller supports Betaflight firmware. You will need to connect the flight controller to your computer via the Type-C USB port and use the Betaflight Configurator software to flash the DAKEFPVF722 firmware and configure your drone's settings. The ESCs support Bluejay firmware and bidirectional DSHOT, which can also be configured via Betaflight passthrough or dedicated Bluejay configurator tools.

6. Operating Instructions

Once the flight stack is correctly wired and configured with Betaflight, you can proceed with operating your FPV drone. The high-performance processor and DSHOT600 protocol support ensure smooth and powerful acceleration. The built-in OSD module allows for real-time display of flight parameters on your FPV feed, which can be customized through Betaflight.

6.1 On-Screen Display (OSD)

The integrated OSD module (AT7456E chip) provides critical flight information directly on your FPV video feed. This includes battery voltage, flight time, current draw, RSSI, and more. Parameters can be adjusted in Betaflight Configurator to display the information most relevant to your flying style.

6.2 Receiver Binding

If using the 2.4G ELRS Nano receiver, follow the ExpressLRS binding procedure specific to your radio transmitter. The receiver offers low latency and high refresh rates, ideal for responsive FPV flying.

7. Maintenance

  • Regular Inspection: Periodically check all solder joints and connections for any signs of wear, corrosion, or damage.
  • Cleaning: Keep the flight stack free from dust, dirt, and moisture. Use compressed air or a soft brush for cleaning.
  • Firmware Updates: Check for new Betaflight and Bluejay firmware releases regularly to benefit from performance improvements and bug fixes.
  • Physical Protection: Ensure the flight stack is adequately protected within your drone frame from crashes and environmental elements.

8. Troubleshooting

  • No Power: Check battery connections, XT60 connector, and ensure the battery is charged. Verify continuity of power lines.
  • No Signal to Motors: Ensure ESCs are properly connected to the flight controller and motors. Check ESC firmware and calibration. Verify DSHOT protocol settings in Betaflight.
  • No FPV Feed/OSD Issues: Check camera and VTX connections. Ensure OSD is enabled and configured in Betaflight.
  • Flight Instability: Re-check gyroscope orientation in Betaflight. Ensure proper vibration damping for the flight controller. Review PID tuning settings.
  • Receiver Not Binding: Ensure the receiver is powered correctly and in binding mode. Verify your transmitter is also in binding mode and on the correct frequency/protocol.

9. User Tips

  • The F722 Flight Stack's design with large solder pads makes it more forgiving for beginners during assembly. Take your time and ensure clean solder joints.
  • The F722 main control chip, onboard OSD, and barometer are designed to provide reliable performance even in complex flight environments, offering robust data for pilots.
  • Utilize the Betaflight Blackbox feature to log flight data, which can be invaluable for diagnosing flight issues and fine-tuning PID settings.
  • Always test your drone in a safe, open area after any changes to wiring or configuration.

10. Warranty and Support

For technical support, troubleshooting assistance, or inquiries regarding product defects, please contact the seller directly through the platform where the product was purchased. Provide your order details and a clear description of the issue, including any relevant photos or videos, to facilitate a quicker resolution.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.