9IMOD F722 Flight Stack

Contents

9IMOD F722 Flight Stack Instruction Manual

Model: F722 Flight Stack

Includes F722 Flight Control and 55A/60A ESC

Introduction

The 9IMOD F722 Flight Stack is a high-performance integrated unit designed for FPV (First Person View) racing drones. It combines an advanced F722 Flight Controller with either a 55A or 60A 4-in-1 Electronic Speed Controller (ESC), offering robust control and power delivery. This stack is built with high-quality components, including an STM32F722RET6 master chip and ICM42688 gyroscope, ensuring precise flight characteristics. It supports 3-6S Lipo batteries (3-8S for 60A ESC variant) and is compatible with popular open-source firmware like Betaflight and BlueJay, supporting DSHOT600 protocol and bidirectional DSHOT.

Safety Information

⚠ WARNING: This product can expose you to chemicals including phthalates (DEHP), which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.

Always exercise caution when working with electronic components, especially those involving high current and voltage. Ensure proper insulation and secure connections to prevent short circuits. Disconnect power before making any changes or repairs. Keep the device away from moisture and extreme temperatures.

Package Contents

Please verify that all items are present in your package:

  • F722 Flight Controller x1
  • 55A ESC x1 (or 60A ESC x1, depending on variant)
  • Package Box x1
  • TS100 GPS Connect Cable x1
  • ESC Connect Cable x1 (or x2 for 60A variant)
  • R8SM Receiver Connect Cable x1
  • Analog Video Transmission Connect Cable x1
  • Camera Connect Cable x1
  • ELRS Receiver Connect Cable x1
  • Power cable + XT60 x1
  • Low ESR capacitor (1000uF 35V/100V) x1
  • Silicone vibration absorber x8
  • Screw x4
  • Hex nut x4
Package contents for 55A ESC variant
Figure 1: Package Contents (55A ESC variant shown)
Package contents for 60A ESC variant
Figure 2: Package Contents (60A ESC variant shown)

Specifications

F722 Flight Control Parameters

FeatureSpecification
Master chipSTM32F722RET6
GyroscopeICM42688
Battery Input3-8S Lipo
USB PortType-C
BarometerBMP280
OSD chipAT7456E
BluetoothNot Supported
RSSI SupportYes (marked as RSSI)
Supported FC FirmwareBetaflight
Firmware NameDAKEFPVF722
Installation Hole Position30.5x30.5mm/M4
Size36mm x 36mm x 8mm
Weight (Bare board)8g
Direct Insertion Solder-Free InterfaceReceiver 4P, Simulated camera 3p-1.25, Digital image transmission 6p, Simulated image transmission 4p, Brushless ESC 8p
F722 Flight Control Parameter Table
Figure 3: F722 Flight Control Parameter Details

55A ESC Parameters

FeatureSpecification
MCUEFM8BB21F16G-C-QFN20R
Continuous Current55A x 4
Transient Current60A-10S
ProgramBlueJay
MOS3109
TVS Protection DiodeYes
Electrolytic Capacitor1000uF Low ESR Capacitor
Motor ProtocolDshot300/600
Battery Input3-6S Lipo
AmmeterSupport
Power OutputVBAT
Installation Hole Position30.5x30.5mm/M4
SizeLength 43x37x7mm
Weight (Bare board)12g
55A ESC Parameter Table
Figure 4: 55A ESC Parameter Details

60A ESC Parameters

FeatureSpecification
MCUEFM8BB21F16G-C-QFN20R
Continuous Current60A x 4
Transient Current65A-10S
ProgramBlueJay
MOS5C430
TVS Protection DiodeYes
Electrolytic Capacitor1000uF Low ESR Capacitor
Motor ProtocolDshot300/600
Battery Input3-8S Lipo
AmmeterSupport
Power OutputVBAT
Installation Hole Position30.5x30.5mm/M4
SizeLength 43x37x7mm
Weight (Bare board)12g
60A ESC Parameter Table
Figure 5: 60A ESC Parameter Details

Setup and Installation

The F722 Flight Stack features a 30.5x30.5mm mounting pattern with M4 holes, making it compatible with many FPV drone frames. Use the provided silicone vibration absorbers to minimize interference from motor vibrations.

Physical Installation

  1. Mount the F722 Flight Stack onto your drone frame using the M4 screws and silicone vibration absorbers. Ensure the orientation is correct as per your flight controller software's requirements.
  2. Connect the power cable (XT60) to the ESC.
  3. Connect the motors to the ESC pads. The ESC supports Dshot300/600 motor protocols.

Wiring Diagrams

The F722 Flight Controller offers standard sockets and large solder pads, designed for ease of use, even for beginners. The pads are kept away from components to facilitate perfect soldering. It also features direct insertion solder-free interfaces for various peripherals.

F722 Full Socket Version Wiring Diagram
Figure 6: F722 Full Socket Version Basic Wiring Diagram. This diagram illustrates connections for motors, LEDs, camera, VTX, SBUS receiver, buzzer, and GPS.
F722 Full Socket Version Detailed Wiring Diagram
Figure 7: F722 Full Socket Version Detailed Wiring Diagram. This diagram shows connections for Crossfire Nano Rx, Camera, ESC, Digital/Simulated VTX, and GPS.

Important Wiring Notes:

  • Ensure correct polarity for all power connections.
  • Utilize the direct insertion solder-free interfaces for compatible receivers, cameras, and video transmission units to simplify wiring.
  • If using a digital image transmission system with SBUS control protocol, short-circuit the solder pad jumper as indicated in the detailed wiring diagram (Figure 7).

Operating Instructions

Firmware Configuration

The F722 Flight Controller supports Betaflight firmware. The ESC uses BlueJay firmware and supports bidirectional DSHOT.

  1. Connect to Computer: Use a Type-C USB cable to connect the flight controller to your computer.
  2. Betaflight Configurator: Open the Betaflight Configurator software. Ensure you have the latest version installed.
  3. Flash Firmware: Select the DAKEFPVF722 target and flash the desired Betaflight firmware version.
  4. ESC Firmware: The ESC comes pre-flashed with BlueJay firmware. If an update is needed, use the appropriate ESC configurator (e.g., BlueJay Configurator) via passthrough from Betaflight.
  5. Initial Setup: Follow the Betaflight setup wizard to calibrate accelerometers, configure ports, receivers, modes, and OSD settings. The built-in OSD module allows for one-step parameterization directly from your FPV goggles.
  6. Motor Protocol: Ensure the motor protocol is set to Dshot300 or Dshot600 in Betaflight. Enable bidirectional DSHOT for advanced motor telemetry.

User Tips

  • Double-Check Connections: Before powering on, always double-check all wiring connections for correct polarity and secure soldering to prevent damage.
  • Firmware Updates: Regularly check for updated Betaflight and BlueJay firmware versions to benefit from new features, bug fixes, and improved performance.
  • Bench Testing: Perform initial bench tests with propellers removed to verify motor direction, ESC calibration, and flight controller response before actual flight.
  • Vibration Management: The provided silicone vibration absorbers are crucial for optimal gyroscope performance. Ensure they are correctly installed and not overtightened.

Troubleshooting

If you encounter issues, consider the following steps:

  • No Power/No Lights: Check battery connection, power cable integrity, and ensure the flight controller is receiving power.
  • No Connection to Betaflight: Verify USB cable connection, try a different USB port, ensure correct drivers are installed (Zadig for DFU mode), and check if the flight controller is in DFU mode if flashing firmware.
  • Motors Not Spinning/Incorrect Direction: Check motor wiring to the ESC, verify motor protocol settings in Betaflight, and ensure ESCs are calibrated. Use the motor tab in Betaflight Configurator to test individual motors.
  • Unstable Flight: Re-check mounting for vibrations, recalibrate accelerometer, and review PID settings. Ensure propellers are balanced and undamaged.
  • OSD Issues: Check OSD settings in Betaflight. Ensure the AT7456E OSD chip is correctly configured.

For more detailed troubleshooting, refer to the official Betaflight documentation and community forums.

Warranty and Support

This product is designed for hobbyist use and requires technical knowledge for installation and operation. Due to the nature of FPV components, specific warranty details may vary. Please refer to the seller's policy for any return or exchange inquiries.

For technical support, please consult online FPV communities, Betaflight documentation, and the manufacturer's resources. Proper installation and configuration are crucial for the performance and longevity of the flight stack.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.