BAOFENG BF-1904

Contents

Baofeng BF-1904 Professional Walkie Talkie User Manual

Model: BF-1904 | Brand: BAOFENG

1. Introduction

Thank you for choosing the Baofeng BF-1904 Professional Walkie Talkie. This high-power, long-range UHF radio is designed for reliable communication across various environments. This manual provides essential information for the safe and efficient operation of your device. Please read it thoroughly before use.

Baofeng BF-1904 walkie talkie demonstrating durability with a graphic of it surviving a fall.
Figure 1.1: The BF-1904 features a hard-sealing shell designed to withstand drops of up to 4 meters.

2. Safety Information

Always observe the following basic safety precautions during operation, service, and repair of this equipment:

  • Do not operate the radio in explosive atmospheres (e.g., flammable gases, dust particles, metallic powders).
  • Do not replace or charge batteries in potentially explosive atmospheres.
  • Turn off your radio before entering any area with blasting caps or in a blasting area.
  • Do not use unauthorized accessories.
  • Do not disassemble or modify the radio.
  • Keep the radio away from medical devices like pacemakers.
  • Avoid exposing the radio to direct sunlight for extended periods or placing it near heating appliances.
  • Ensure the antenna is properly attached before transmitting to prevent damage to the radio.

3. Package Contents

The standard package for your BF-1904 Walkie Talkie includes the following items. Please check all items upon unpacking:

Baofeng BF-1904 radio and included accessories: radio unit, battery, antenna, belt clip, hand strap, user manual, and Type-C charging cable.
Figure 3.1: Standard Package Contents
  • 1 x BF-1904 Radio Unit
  • 1 x Antenna
  • 1 x Battery Pack
  • 1 x Type-C Charging Cable
  • 1 x Belt Clip
  • 1 x Hand Strap
  • 1 x English User's Manual

Note: Additional accessories may be included depending on your specific purchase variant.

4. Product Overview

Familiarize yourself with the various parts and controls of your BF-1904 radio.

Diagram of Baofeng BF-1904 radio showing Channel Knob, Power Volume Switch, LED Indicator, PTT button, Radio body, Earphone Mic Jack, Speaker, and Microphone.
Figure 4.1: BF-1904 Radio Components
  • Antenna: For transmitting and receiving signals.
  • Channel Knob: Used to select one of the 16 available channels.
  • Power/Volume Switch: Rotates to turn the radio ON/OFF and adjust the volume.
  • LED Indicator: Shows radio status (e.g., transmitting, receiving, low battery).
  • PTT (Push-To-Talk) Button: Press and hold to transmit, release to receive.
  • Microphone (MIC): For speaking during transmission.
  • Speaker: For audio output.
  • Earphone/Mic Jack: For connecting external audio accessories.
  • Type-C Charging Port: For charging the battery.

5. Setup

5.1. Attaching the Antenna

Screw the antenna into the connector on the top of the radio by turning it clockwise until it is secure. Do not overtighten.

5.2. Installing the Battery Pack

Align the battery pack with the grooves on the back of the radio and slide it upwards until it clicks into place. To remove, press the release latch (if present) and slide the battery downwards.

5.3. Attaching the Belt Clip

Use the provided screws to attach the belt clip to the back of the radio, if desired.

5.4. Charging the Battery

Connect the Type-C charging cable to the charging port on the radio and plug the other end into a compatible USB power source. The LED indicator will typically glow red during charging and turn green when fully charged. Ensure the radio is turned off during charging for optimal battery life.

6. Operating Instructions

6.1. Power On/Off and Volume Adjustment

Rotate the Power/Volume switch clockwise to turn the radio ON. Continue rotating clockwise to increase the volume. Rotate counter-clockwise to decrease volume and turn the radio OFF.

6.2. Channel Selection

Rotate the Channel Knob to select one of the 16 available channels. The radio may announce the channel number if voice reporting is enabled.

6.3. Transmitting and Receiving

  • To Transmit: Press and hold the PTT button. Speak clearly into the microphone. The LED indicator will typically glow red.
  • To Receive: Release the PTT button. The LED indicator will typically glow green when a signal is being received.

6.4. CTCSS / DCS (Tone Squelch)

Your radio supports 50 Groups CTCSS and 105 Groups of standard DCS. These tones help filter out unwanted conversations on the same channel. These settings are typically programmed using frequency writing software.

6.5. TOT (Time-out Timer)

The Time-out Timer prevents a user from transmitting on a channel for an excessively long period. If the transmission exceeds the preset time, the radio will stop transmitting and emit an alert tone. This feature is programmable via software.

6.6. Battery Save Mode

When enabled via frequency writing software, the radio will automatically enter a power-saving state after approximately 5 seconds of no operation. This helps extend battery life. Turning off the radio does not save power in this mode.

6.7. Alarm Function

The radio includes an alarm function. Specific activation methods and alarm types (e.g., local, remote) are typically configured via programming software.

6.8. H/L Power Shift

This feature allows you to switch between High and Low transmit power settings, usually configured via programming software. Low power conserves battery life and is suitable for short-range communication, while high power is for maximum range.

6.9. FM Radio

The BF-1904 includes an FM radio function. Consult the programming software or specific key combinations (if available) to activate and tune the FM radio.

6.10. Voice Reporting (Chinese/English)

To switch the voice reporting language between Chinese and English, turn off the radio. Then, press and hold both the PTT key and the MONI key simultaneously while turning the radio ON. This action toggles the language setting.

6.11. Monitor Function

Press the MONI key (often a side button) to temporarily disable squelch and listen to weak signals or noise on the current channel. This is useful for monitoring channels with very low signal strength or for adjusting volume when no signal is present.

6.12. VOX Function (Voice Operated Transmit)

The VOX function allows you to transmit automatically by speaking into the microphone without pressing the PTT button. To toggle VOX on/off, turn off the radio. Then, press and hold both the PTT key and the MONI key simultaneously while turning the radio ON, specifically on CH1. It is recommended to configure VOX sensitivity and other parameters using the frequency writing software.

7. Maintenance

7.1. Cleaning

Clean the radio's surface with a soft, damp cloth. Do not use harsh chemicals or abrasive cleaners. Ensure the charging port and accessory jacks are free of dust and debris.

7.2. Battery Care

  • Charge the battery fully before initial use.
  • Avoid overcharging or completely draining the battery.
  • Store the battery in a cool, dry place when not in use for extended periods.
  • If the radio prompts "low battery," charge or replace the battery pack promptly.

7.3. Storage

When storing the radio for long periods, remove the battery pack. Store the radio and battery in a cool, dry, and dust-free environment.

8. Troubleshooting

ProblemPossible CauseSolution
Radio won't turn on.Battery is dead or not properly installed.Charge the battery or ensure it is correctly attached.
Cannot transmit or receive.Incorrect channel selected, low battery, or antenna not connected. CTCSS/DCS mismatch.Check channel, charge battery, ensure antenna is secure. Verify CTCSS/DCS settings match.
Poor audio quality or static.Weak signal, interference, or antenna issue.Move to an open area, check antenna connection, try a different channel.
"Low battery" prompt.Battery charge is critically low.Charge the battery immediately.

9. Specifications

FeatureSpecification
Model NumberBF-1904
Frequency Range400-520MHz
Output Power10W-25W
Battery CapacityHigh Capacity (Li-ion)
Battery VoltageDC 7.4V
Storage Channels16
Waterproof / Water-ResistantIP45
MaterialStrong Polycarbonate Plastic
Dimensions (approx. package)25.50 x 21.00 x 6.00 cm
Maximum Range10km-50km
Frequency Stability±2.5ppm
Audio Output1000mW
Antenna Impedance50 Ohm
Operating Temperature-20°C to +50°C
ModulationFrequency Modulation (F3E)
Max Frequency Deviation≤±5KHz
Residual Wave Radiation<-60dB
Emission Current≤2.6A
Receiving Sensitivity<0.15μV
CertificationsCE, Dot, EAC, EPA, FCC, GMP, RoHS, TGA, UL, KC, pse, weee

Note: Specifications are subject to change without notice.

10. User Tips

  • For optimal range, ensure you are in an open area with minimal obstructions.
  • Consider using the low power setting for shorter distances to conserve battery life.
  • If experiencing interference, try switching to a different channel or adjusting CTCSS/DCS settings (requires programming software).
  • Regularly check the battery level, especially before critical operations.
  • The Type-C charging port offers convenient charging from various USB power sources.

11. Warranty and Support

For warranty information, technical support, or service inquiries, please refer to the contact information provided by your retailer or the official Baofeng website. Keep your purchase receipt as proof of purchase.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.