G-NiceRF DMR858S-V

Contents

G-NiceRF DMR858S-V 5W Digital Walkie Talkie Module

Instruction Manual

1. Introduction

The G-NiceRF DMR858S-V is an all-in-one 5W digital walkie talkie module designed for professional communication. It integrates both analog and Digital Mobile Radio (DMR) functionalities, ensuring compatibility with existing walkie talkie systems, including Motorola compatible devices. The module features a DSP processor, DMR encoder/decoder, RF/Audio Amplifier, PTT (Push-to-Talk), Microphone input, a 16-channel switch, and volume adjustment, all on a single board. By connecting a power supply and a speaker, a complete 5W professional DMR walkie talkie can be assembled. This module is engineered to deliver excellent voice quality and reliable communication range, incorporating special heat sinks to ensure stable performance during extended operation.

2. Package Contents

Please verify that all items listed below are included in your package:

  • 1x DMR858S-V Digital Walkie Talkie Module (VHF 134-174MHz)
  • 1x Rubber Antenna

3. Key Features

  • Frequency Bands: UHF (400-470 MHz), VHF (134-174MHz), and 350MHz (320-390MHz) options available.
  • Voice Encoder: NVOC and AMBE++ (Motorola compatible) options.
  • Range: Up to 7 Km in open areas.
  • Output Power: Up to 5W.
  • Sensitivity: Up to -124dBm.
  • BER Performance: Less than 1% BER @ -121dBm.
  • Frequency Setting: TX/RX frequencies can be set separately.
  • Bandwidth: 12.5 / 25 KHz for analog, 6.25KHz for DMR.
  • Modes: Combined DMR / Analog walkie talkie functionality.
  • Messaging: Supports IP confirmed/unconfirmed SMS, with pre-save SMS capability.
  • Timing: Equipped with 1ppm TCXO Crystal for high accuracy.
  • Signaling: 51 levels of CTCSS and 166 levels of CDCSS.
  • Volume Control: 9 classes of digital volume and continuous (stepless) analog volume.
  • Security: Encryption for SMS and voice communication.
  • Calling Types: Supports broadcast, group call, and private call.
  • Alerts: Reminder for incoming calls and calling status checks.
  • Enhanced Functions: Emergency alarm and radio monitor support.
  • Scanning: Frequency scan capability.
  • Remote Control: Supports Radio kill and activate functions.
  • Signal Strength: RSSI value readout available.
  • Configuration: PC software provided for easy configuration.
  • Memory: EEPROM inside for parameter storage, even when powered off.

4. Technical Specifications

4.1 General Parameters

ParameterConditionMinTypMaxUnit
Power Supply3.389.0V
Working temperature-302570°C
Frequency Range@UHF400480MHz
@VHF134174MHz
@350320390MHz
Serial baud rate57600bps

4.2 Current Consumption

ParameterConditionMinTypMaxUnit
Sleep current<50uA
RX Current<100mA
TX current@VCC=8.0V,5W<1.6A
@VCC=8.0V,3W<1.1A
@VCC=4.0V, 1.8W<1000mA
@VCC=4.0V,1W<750mA

4.3 RF Performance

ParameterConditionMinTypMaxUnit
TX Power@high power, 4v1.6W
@low power, 4v1.0W
@high power, 8v455.5W
@Low power, 8v233.5W
Mic input voltage0.11.6Vpp
RX Sensitivity-124dBm
BER @DMR mode@ -121dBm1
Speaker2W & 8 ohm

4.4 Dimensions

The DMR858S-V module has the following dimensions:

  • Main Module: 59.1 x 10.68 x 2.72 mm
  • Control Board: 37.6 x 24.2 x 8.0 mm
Mechanical dimensions of the control board
Figure 1: Mechanical dimensions of the control board.
Mechanical dimensions of the main module
Figure 2: Mechanical dimensions of the main module.

5. Setup Instructions

The DMR858S-V module is designed for integration into custom applications. Below are the general steps and pin definitions for setting up the module.

5.1 Application Schematic

The module consists of a DMR Functional Board and a DMR Control Board connected via an 18-pin FPC. The functional board handles RF transmission/reception, while the control board provides interfaces for power, audio, PTT, and configuration.

Application Schematic for DMR858S-V module
Figure 3: Application Schematic showing interconnection between DMR Functional Board and DMR Control Board.

5.2 Pin Definitions

Careful attention to pin connections is crucial for proper operation. Refer to the tables and diagrams below for detailed pin assignments.

DMR Control Board layout with pin numbers
Figure 4: DMR Control Board layout with pin numbers and switches.
Pin No.DefinitionDescription
1VCCVDD (connected to Pin 19 of function board)
2,4GNDGround
3CSConnect to CS of the function board
5PTTConnect to PTT of the function board
6LINE_OUTConnect to Line Out of the function board
78Frequency channel indicator (16 channel selected): 8: the maximum bit
844: the 3rd bit
922: the 2nd bit
1011: the least bit for example: 8421 encoding: 0000: channel 0, 0001: channel 1, 0010: channel 2, 0011: channel 3 ... 1111: channel 15
11SPKNConnected with Speaker: 8 Ohm 2W
12SPKPConnected with Speaker: 8 Ohm 2W
13,15,17GNDGround
14SETSetting mode (0: setting mode, 1: normal mode)
16MIC_INConnect to MIC_IN of the function board
18TXDConnect to TXD/RXD of the function board
19RXDConnect to TXD/RXD of the function board
20,21,22,23NCNC
24GNDGround
DMR Functional Board layout with pin numbers
Figure 5: DMR Functional Board layout with pin numbers.
Pin No.DefinitionDescription
1, 2, 4GNDGround
3MIC_INMicrophone input
5UART-RXConnected with UART-TX of external device
6UART-TXConnected with UART-RX of external device
7, 13GNDGround
8CSSleep: 0; working: 1 (default when leave open)
9PTTTX: 0, RX: 1 (Default)
10LINE_OUTLine out for voice
11T/RTX/RX indicator, 1: TX, 0: RX
12SPKENExternal Voice amplifier on/off; 1: on, 0:off
14, 15+3.3 V3.3V output, maximum 50mA loading
16,17,18,19VCCVCC (3.3V-9V)
20GNDGround

5.3 Parameter Configuration

Parameters can be configured using either the standard mini-USB interface or the serial UART interface. PC software is provided to simplify the configuration process. This software allows users to set all necessary parameters for the module.

All parameters can also be configured using a Serial Communication Protocol. The Most Significant Bit (MSB) is used for commands.

6. Operating Instructions

6.1 Channel Selection

The module comes with 16 default channels pre-set. Channels 0-7 are configured for DMR operation, while channels 8-15 are for analog walkie talkie functionality. A rotary switch on the control board is used to change between these channels. Pins 7-10 output the current channel status using 8421 encoding.

6.2 Volume Adjustment

The module supports both digital and analog volume control. Digital volume has 9 classes, while analog volume is continuous (stepless).

6.3 Communication Modes

The DMR858S-V supports various voice calling types:

  • Broadcast: Transmit to all devices within range.
  • Group Call: Communicate with a predefined group of devices.
  • Private Call: Establish one-to-one communication with a specific device.

The module also provides reminders for incoming calls and allows for checking the calling status.

6.4 Advanced Functions

The module includes enhanced functions such as emergency alarm, radio monitor, and frequency scanning. It also supports radio kill and activate features for remote management.

7. Maintenance

To ensure the longevity and optimal performance of your DMR858S-V module, follow these maintenance guidelines:

  • Environmental Conditions: Keep the module in a dry environment and avoid exposure to extreme temperatures, humidity, or direct sunlight.
  • Cleaning: Gently clean the module with a soft, dry cloth. Do not use harsh chemicals or solvents.
  • Heat Management: The module is equipped with special heat sinks to manage heat during prolonged operation. Ensure adequate airflow around the module if integrating it into an enclosure.
  • Connections: Periodically check all connections (power, antenna, audio, data) to ensure they are secure and free from corrosion.

8. Troubleshooting

If you encounter issues with your DMR858S-V module, refer to the following common problems and solutions:

  • No Power:
    • Check the power supply voltage (3.3V-9V) and ensure it is correctly connected to the VCC and GND pins.
    • Verify that the power source is providing sufficient current.
  • No Audio Output:
    • Ensure the speaker is correctly connected to SPKN/SPKP pins (8 Ohm 2W).
    • Check the volume settings (digital/analog).
    • Verify the LINE_OUT connection if using an external audio amplifier.
  • Cannot Transmit or Receive:
    • Confirm the antenna is securely connected to the SMA connector.
    • Check the PTT connection (Pin 5 on control board, Pin 9 on functional board).
    • Verify that the frequency and channel settings are correct and match the intended communication partner.
    • Ensure the module is in 'normal mode' (SET pin 1 on control board).
    • Check the CS pin (Pin 3 on control board, Pin 8 on functional board) to ensure the module is not in sleep mode.
  • Poor Communication Range:
    • Ensure the antenna is appropriate for the operating frequency band.
    • Check for obstructions or interference in the environment.
    • Verify the output power setting via PC software.
  • Configuration Issues:
    • Ensure the correct PC software version is being used.
    • Verify the serial UART connections (TXD/RXD) or USB connection.
    • Check baud rate settings for serial communication.

9. User Tips

  • Optimal Antenna Placement: For best range and signal quality, ensure the rubber antenna is positioned vertically and away from metallic obstructions.
  • Leverage PC Software: Utilize the provided PC software for precise configuration of frequencies, channels, and advanced features. This allows for fine-tuning the module to your specific application needs.
  • Understand Channel Types: Remember that channels 0-7 are for DMR digital communication, while channels 8-15 are for analog. Ensure your communication partners are on compatible channels and modes.
  • Power Supply Stability: Use a stable power supply within the recommended voltage range (3.3V-9V) to prevent unexpected behavior or damage to the module.
  • Heat Dissipation: While the module has heat sinks, if integrating into a compact enclosure, consider additional ventilation to maintain optimal operating temperature, especially during high-power transmissions.

10. Warranty and Support

All G-NiceRF products undergo quality control before shipping and are well-packed. This product comes with a 1-year guarantee from the date of purchase.

For technical support, inquiries, or further assistance, please contact:

  • WhatsApp: +86 18525855617
  • Email: 2597264449@qq.com
Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.