ETENWOLF V3

Contents

ETENWOLF V3 Portable Tire Inflator Pump

User Manual

Introduction

Thank you for choosing the ETENWOLF V3 Portable Tire Inflator Pump. This manual provides essential information for the safe and efficient operation of your device. Please read all instructions and safety warnings carefully before use to ensure proper functionality and to prevent injury or damage.

Warning! Please read all safety warnings and all instructions to reduce the risk of electric shock, fire, and/or serious injury.

Package Contents

Please check the box for the following items:

  • 1 x ETENWOLF V3 Air Compressor
  • 1 x Air Chuck
  • 1 x USB A to C Charging Cable
  • 1 x Cone-shaped blowing nozzle
  • 1 x Ball needle
  • 1 x French copper adapter
  • 1 x T-shaped quick connector
  • 1 x User Manual (this document)
ETENWOLF V3 Package Contents

Image: ETENWOLF V3 Air Inflator box with the inflator and all included accessories laid out.

Product Overview

Familiarize yourself with the components of your ETENWOLF V3 inflator:

ETENWOLF V3 Product Diagram

Image: Detailed views of the ETENWOLF V3 inflator from multiple angles, highlighting the control panel, hose storage, and ports.

  1. Light button
  2. Mode button (Switchable Units)
  3. "+" Increase pressure button
  4. Start/pause power button
  5. Center display
  6. "-" Decrease pressure button
  7. LED work light
  8. Type-C port (Input)
  9. USB-A port (Output)
  10. Pressure hose
  11. Presta valve adapter
  12. Inflation needle
  13. High-pressure tapered nozzle

Setup and Quick Start Guide

Follow these steps for initial setup and to begin inflation:

  1. Remove the Pressure Hose: Take the pressure hose from its storage channel on the unit.
  2. Connect the Nozzle: Insert the nozzle clockwise into the valve stem of the item being inflated. Ensure a secure connection to prevent air leakage.
  3. Power On: Press the Start/pause power button (4) for 3 seconds to activate the machine.
  4. Select Mode: Press the Mode button (2) to switch among the four different inflation modes: Manual mode, Car mode, Bicycle mode, and Ball mode.
  5. Select Pressure Unit: Press the Mode button (2) for more than 1 second to cycle through pressure units: PSI, KPa, and Bar.
  6. Adjust Target Pressure: Use the "+" button (3) to increase the target pressure value or the "-" button (6) to decrease it.
  7. Start Inflation: Press the Start/pause power button (4) again to begin inflation.
  8. Automatic Shut-off: The unit will automatically turn off once the inflated item reaches the preset pressure value.
Easy to Use Inflation Steps

Image: A four-panel diagram illustrating the easy-to-use steps for inflation: 1. Remove valve cap and connect, 2. Long press 3s startup, 3. Press M to select mode, 4. Press start inflating. Dimensions of the device and hose length are also shown.

Using Attachments: The Presta valve adapter (11), inflation needle (12), and high-pressure tapered nozzle (13) are conveniently stored on the back side storage panel of the inflator.

Operating Instructions

Button Operation Guide

  • MODE Button (2): Short press to switch between Car, Bicycle, Ball, and Manual inflation modes. Long press (more than 1 second) to select pressure units (PSI, KPa, Bar).
  • Start/Pause Power Button (4):
    • ON: Long-press for two seconds to turn on the inflator.
    • OFF: While the inflator is on, long-press for two seconds to turn it off.
    • Pause: During inflation, press once to pause the machine. Press again to resume.

Preset Pressure Values

The display shows the target input value (smaller size) and the actual pressure value (bigger size). The default preset values are:

ModeAdjustable Pressure RangeDefault Pressure
Manual mode3-160 PSI30 PSI
Car mode8-130 PSI35 PSI
Bicycle mode10-145 PSI22 PSI
Ball mode3-16 PSI8.5 PSI

LED Work Light (7)

The LED work light is located at the front of the inflator. To turn it on, first power on the machine, then press the Light button (1). It features four modes: Bright flashlight, Ultra-bright flash light, Slow strobe light, and SOS light.

Note: The light automatically turns off after 1 hour. If manually turned on a second time, it will stay on until manually turned off.

Power Bank Function

The ETENWOLF V3 doubles as a power bank, ready to charge your electronic devices via its USB-A Output (5V 2A, 10W). The inflator needs to be powered on for this function. After 3 minutes of charging, the display will show only the battery level to conserve power. It will automatically turn off after 2 minutes of fully charging the connected device.

ETENWOLF V3 as a Power Bank

Image: The ETENWOLF V3 inflator connected via USB to charge a smartphone and other electronic devices, highlighting its 7800mAh power bank capability.

Battery Charging & Indicator

Charging with AC Power Supply

For optimal performance, use a 5V 3A 15W PD charger with the provided USB A to C cable. A full charge from 0% to 100% takes approximately 2-3 hours.

Battery Indicator

The battery level indicator (22) on the display shows four bars, with each bar representing 25% of the battery capacity.

Note: The inflator cannot be used while it is charging. It will automatically shut off after 2 minutes of inactivity once fully charged.

Maintenance

Pressure Recalibration

Altitude can affect pressure readings (1-3 PSI variance). If you are in high-altitude areas (over 5000 ft/1524 meters), you can recalibrate the pump's pressure sensor:

  1. Power on the pump (4).
  2. Hold the Light button (1) and Mode button (2) simultaneously for 10 seconds.
  3. The entire screen will flicker, indicating recalibration is complete.

Important Notes for Recalibration:
• Power off the pump before starting.
• The pressure hose (10) must NOT be connected to any item.
• A charged battery or external power source is required.
• Recalibration settings are not saved; they reset to sea level calibration (0 ft/meters) when the power is turned off.

General Care

  • Use the product in a dry and clean environment. Avoid sand and dust intrusion, which can damage the product. Do not wash the product with water.
  • Store the product within temperatures ranging from -10°C to 60°C (14°F to 140°F). Extreme temperatures can damage the battery and shorten the inflator's lifespan.
  • For long-term storage, charge the inflator at least once every three months to maintain battery performance.

Troubleshooting

If you encounter any issues, refer to the table below for common problems and solutions:

ProblemSolution
Slow inflation speedCheck for leaks in the item, tighten air nozzle connection, inspect hoses for damage, and ensure ventilation slots are clear.
Air compressor turns on, but does not inflateVerify if the item's pressure exceeds the preset pressure.
Unable to increase or decrease preset pressureEnsure correct mode is chosen and preset value is within range. Adjust in Manual mode (3-160 PSI).
Inflator inflates but display shows zeroIf air pressure is under 3 PSI, the display will show zero due to the pump's minimum pressure range.
Battery level indicator not shown after chargingUse a certified charger and the included charging cable.
Air leakage when connecting high-pressure air hoseTighten the air nozzle securely.
Unable to charge other devicesCheck battery level. Verify charging device is 5V 3A compatible. Cannot be used as power source while charging. Use original charging cable.
Safety alert symbol (E08 error code)If issue persists after restart, send device for factory repair.
E10 error code (Motor malfunction)Motor malfunction. If issue persists after restart, send for factory repair.
E11 error code (Low-temp charging)Restore temperature above 0°C before charging.
E12 error code (High-temp charging)Restore temperature below 45°C before charging.
E13 error code (Low-temp discharge)Restore temperature above -20°C before use.
E14 error code (High-temp discharge)Restore temperature below 58°C before use.
E15 error code (Over-working time)Air pump exceeded working time. Check for leaks.
E16 error code (Overpressure)Returns to normal after pressure release.
E17 error code (High-pressure operation)High-pressure operation exceeded working time. Check if item is functioning abnormally.
E18 error code (Battery damage)Battery damage. Device will shut down. Send for factory repair.

Specifications

Here are the technical specifications for your ETENWOLF V3 Portable Tire Inflator Pump:

FeatureSpecification
ModelZephyr V3 Air Compressor
Dimensions (L x W x H)14.3 cm x 11.2 cm x 19.6 cm (5.63 in x 4.41 in x 7.72 in)
Item Weight1.2 kg (2.65 lbs)
Inflation Pressure Range3-160 PSI / 0.2-11 Bar
Operating TemperatureCharging: 0°C-45°C (32°F-113°F)
Discharging: -20°C-74°C (-4°F-165°F)
Storage Temperature-10°C-60°C (14°F-140°F)
High Pressure Air Tube Length90 cm (0.9 meters)
Battery Capacity7800mAh
Inflation Speed22L/Min @ 0PSI (0.75CFM @ 0PSI)
Working NoiseLower than 85dB within 1 meter
InputType-C: 5V 3A (15W PD Fast Charging)
OutputUSB-A: 5V 2A
Charging Time2-3 hours
Continuous Working TimeApprox. 25 minutes (at 20-50 PSI, 25°C ambient temp, full charge)
Sensor Accuracy±1 PSI
Duty Cycle100% (runs continuously for over 18 minutes)
ETENWOLF V3 Dimensions and Inflation Speed

Image: The ETENWOLF V3 inflator next to a car tire, illustrating its dimensions (17.4cm H, 13.4cm W, 9.6cm D) and highlighting its 2x faster inflation speed, capable of refilling a 235/45/R18 SUV tire from 30 PSI to 35 PSI in less than 1 minute.

User Tips

  • Users appreciate the fast inflation speed, especially for bicycle tires and car tires (e.g., Tesla to 42 PSI).
  • The 90cm long hose provides convenience and flexibility during use.
  • The automatic shut-off feature when the target pressure is reached is highly valued for ease of use.
  • Its compact and portable design makes it easy to store in a car glove compartment.
  • The rotating nozzle ensures a secure fit on valve stems, preventing accidental detachment during inflation.
  • While generally efficient, some users note it can be a bit noisy during operation.

Safety Instructions

  • This product is not a toy and should not be used by children. Users must be above 16 years old. Keep a safe distance from children during inflation.
  • The product contains a built-in lithium battery. Do not place the product into fire or dispose of the battery improperly.
  • Avoid overheating or water ingress, as this increases the risk of fire or explosion. Keep the product away from heat sources and do not leave it in a hot car for prolonged periods.
  • The product has a built-in DC motor that may generate sparks. Do not use it in environments with dust or flammable gases.
  • If you notice unusual noise or excessive heat during inflation, turn off the inflator immediately.
  • Always ensure the correct pressure unit (PSI, Bar, KPa) is selected before setting the inflation pressure to avoid dangerous overinflation.
  • Do not leave the pump unattended while it is in operation.
  • To reduce the risk of electric shock, do not expose the product to rain. Store indoors in a dry place.

Warranty & Support

2-Year Coverage

ETENWOLF provides a 2-year warranty from the date of purchase. During this period, we will repair or replace any defective product due to manufacturing faults. For any after-sales inquiries or support, please contact ETENWOLF customer service. We are committed to providing professional and efficient service.

For further assistance, please refer to the official ETENWOLF website or contact their customer support channels.


Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.