E-ACE K07/K07P

Contents

E-ACE Smart TPMS Car Tire Pressure Alarm Temperature Monitor System User Manual

Models: K07 / K07P

1. Product Overview

Thank you for purchasing our Tire Pressure Monitoring System (TPMS). This system is designed to provide you with enhanced protection while driving by proactively warning you about tire conditions. Once installed, the TPMS continuously monitors tire pressure and temperature in real-time. Should any abnormal tire pressure or temperature be detected, the system will emit an audible warning and display a flashing icon to alert the driver. These real-time alerts and problem-solving capabilities help prevent traffic accidents and ensure the safety of both drivers and passengers.

Important Reminder: Please read this instruction manual carefully before use. It is not recommended to change the machine parameters unless specifically required. The schematic diagrams in this manual are for reference only; please refer to the actual product for precise details. Before installation, ensure the host unit is powered on!

Key Features

  • Solar power charging, eliminating the need for a car cigarette lighter connection.
  • Colorful LCD Digital display for clear tire information.
  • Real-time monitoring of pressure and temperature for all four tires.
  • Alarms for low air pressure, high temperature, leakage, and low battery.
  • Intelligent Shock Boot: Automatically turns on when the car moves and off when stationary, no manual operation required.
  • Wireless connection via sensors for easy installation.
  • Available with either built-in or external sensors to suit your needs.
  • Equipped with Freescale chip sensors, compatible with approximately 98% of cars on the market.
  • Host setting range: 0.5 Bar - 6.0 Bar / 0.05 MPa - 0.6 MPa / 7 psi - 87 psi.

Charging

The TPMS monitor supports dual charging methods: solar power and USB. The integrated solar panel allows for automatic charging under sunlight, reducing the need for additional wiring. For auxiliary charging or when solar power is insufficient, the device can be charged via its Micro USB port.

E-ACE TPMS display unit showing solar charging and USB charging port.
The E-ACE TPMS display unit features both solar charging capabilities and a Micro USB port for auxiliary charging.
E-ACE TPMS display unit with solar panel and USB charge port labeled.
Solar charging panel and USB charge port on the TPMS display unit.

Intelligent On and Off

The system features an intelligent shock boot function. When the car starts moving, the TPMS monitor automatically turns on. When the car is stationary for a period, the monitor automatically shuts down, eliminating the need for manual operation.

E-ACE TPMS display unit showing intelligent solar car TPMS features including solar charging and beep prompt.
Intelligent Solar Car TPMS with features like solar charging and beep prompts.

2. Setup

2.1. Initial Activation and Monitor Placement

Upon receiving the TPMS, charge it for 3-4 hours to activate the battery, as it may have discharged during transit. It's normal if it doesn't turn on immediately.

Please turn on the monitor before installing the sensors.

  1. Press and hold the power button on the monitor to turn it on.
  2. Once the monitor is on, proceed with sensor installation.
  3. Apply the adhesive to the bottom of the main unit and place it in a suitable position on the left side of the center console. The product does not require any settings and does not need to be turned on or off manually after initial setup.
Diagram showing how to turn on the monitor and install external or built-in sensors.
Step 1: Press and hold the power button to turn on the monitor. Step 2: Install external or built-in sensors one by one.

2.2. External Sensor Installation (Model K07)

External sensors are easy and convenient to install. They are dust-proof, water-proof, anti-theft, and resistant to high/low temperatures.

  1. Screw in the anti-theft nut onto the tire valve stem first.
  2. Tighten the sensor onto the valve stem according to its designated position (e.g., FL for Front Left, FR for Front Right, RR for Rear Right, RL for Rear Left).
  3. Screw the anti-theft nut counter-clockwise against the sensor.
  4. Use the provided wrench to tighten both the sensor and the anti-theft nut securely.

If no pressure is displayed for a corresponding tire on the host, reinstall the sensor.

Diagram showing the steps for external sensor installation: screwing in anti-theft nut, tightening sensor, screwing anti-theft nut counter-clockwise, and tightening with a wrench.
Schematic diagram of external sensor installation steps.

Video demonstrating the installation of external sensors on a car tire.

2.3. Built-in Sensor Installation (Model K07P)

Built-in sensors offer more stable and accurate readings but require professional installation.

  1. Take off the original tire valve.
  2. Mount the tire pressure sensor according to its designated position.
  3. Pump up the tires.
  4. Cover the valve bonnet.
  5. Perform a balancing machine test.
  6. Regulate and counterweight, then install the balancing block.

The tires must be inflated after installation while the main unit is turned on.

Diagram showing the steps for built-in sensor installation: removing valve, mounting sensor, inflating tire, covering valve, balancing, and adding counterweight.
Built-in sensor installation example steps.

3. Operating Instructions

3.1. Interface and Display Description

The TPMS monitor features a clear LCD display showing real-time tire data. The interface includes various indicators and buttons for easy operation.

E-ACE TPMS display unit showing tire pressure and temperature readings for all four tires, along with battery and solar charging indicators.
TPMS display showing tire pressure, temperature, and system status.
Detailed diagram of the K07/K07P TPMS display unit with labels for buttons, ports, and display elements.
K07/K07P Product Display with labeled components.

Display Elements:

  1. Power/Left button: Used for power control and left navigation.
  2. SET button: Used to enter menu mode and confirm selections.
  3. Right button: Used for right navigation and setting adjustments.
  4. Solar energy: Indicates solar charging activity.
  5. Solar icon: Visual indicator for solar charging.
  6. Tire pressure units: Displays the current pressure unit (e.g., BAR, PSI).
  7. Tyre temperature: Shows the temperature of each tire.
  8. Tire Pressure: Displays the pressure of each tire.
  9. Temperature unit: Displays the current temperature unit (e.g., °C, °F).
  10. Battery: Indicates the monitor's battery level.
  11. Clock: Displays the current time (for models with clock function).

3.2. Button Function Description

  • USB (Charging Port): Used for auxiliary charging of the receiver.
  • Power/Left Button:
    • In standby mode: Short press to adjust brightness.
    • Long press to turn the device on or off.
    • In menu mode: Left to switch menu options.
  • Right Button:
    • In standby mode: Short press to adjust brightness.
    • Long press to turn off the alarm.
    • In menu mode: Right to switch setting options.
  • SET Button (Menu/Confirm Button):
    • In standby mode: Long press to enter menu mode.
    • In menu mode: Short press once to select the parameter to be adjusted and confirm.

3.3. Basic Functions

  • Default Settings: The factory default tire pressure unit is BAR, the temperature unit is °C. The upper limit for tire pressure is 3.2 bar, the lower limit is 1.8 bar, and the temperature alarm value is 68°C.
  • Backlight Brightness: The backlight brightness automatically adjusts based on ambient light intensity. It can also be manually adjusted using the Left and Right buttons.

Users can customize parameters according to their vehicle conditions or specific needs. If no modifications are made, the system will operate with its factory default settings. To enter the system setting state, press and hold the 'Menu' button for 3 seconds. If there is no operation for 30 seconds, the system will automatically exit to the main interface, and any unconfirmed settings will not be saved. After completing any setting, long press the 'Menu' key to return to the main interface.

4.1. Unit Setting (Factory Default: Bar, °C)

  1. In standby mode, long press the 'Menu' button for 3 seconds to enter the system setting state. The 'Bar' icon will appear in the lower left corner.
  2. Press the 'Menu' button to enter the operable setting state.
  3. Use the 'Left' and 'Right' buttons to select either 'Psi' or 'Bar' as the pressure unit.
  4. Once the desired unit is selected, press the 'Menu' button to confirm and complete the setting.
  5. To set the temperature unit, after entering the system setting state (step 1), press the 'Right' button once.
  6. Press the 'Menu' button to enter the operable setting state for temperature unit.
  7. Use the 'Left' and 'Right' buttons to select either '°C' or '°F'.
  8. Press the 'Menu' button to confirm and complete the setting.
TPMS display showing unit setting options for pressure (Bar/Psi) and temperature (Celsius/Fahrenheit).
Unit setting interface for pressure and temperature.

4.2. Time Setting (For models with clock function only)

  1. In standby mode, long press the 'Menu' button for 3 seconds to enter the system setting state.
  2. Press the 'Right' button twice to enter the time setting.
  3. Short press the 'Menu' button twice; the hour number will flash.
  4. Use the 'Left' and 'Right' buttons to adjust the hour.
  5. After setting the hour, short press the 'Menu' key to set the minutes.
  6. Adjust the minutes using the 'Left' and 'Right' keys.
  7. Long press the 'Menu' key to exit the setting after the time is complete.
TPMS display showing time setting interface with flashing hour digits.
Time setting interface on the TPMS display.

4.3. Changing Tire Pressure Limits

  1. In standby mode, long press the 'Menu' key for 3 seconds to enter the system setting state.
  2. Press the 'Right' button twice to enter the maximum air pressure setting.
  3. Press the 'Menu' key once; the air pressure number will flash.
  4. Use the 'Left' and 'Right' buttons to set the maximum air pressure.
  5. After setting, long press the 'Menu' key to exit.
  6. To set the lower limit, after entering the system setting state (step 1), press the 'Right' button three times.
  7. Press the 'Menu' key once; the air pressure number will flash.
  8. Use the 'Left' and 'Right' buttons to set the lower limit parameter value.
  9. After setting, long press the 'Menu' key to exit.
TPMS display showing settings for upper and lower tire pressure limits.
Setting interface for tire pressure upper and lower limits.

4.4. Changing Temperature Limits

  1. In standby mode, long press the 'Menu' key for 3 seconds to enter the system setting state.
  2. Press the 'Right' button four times to enter the tire temperature upper limit setting.
  3. Short press the 'Menu' button once; the tire temperature number will flash.
  4. Use the 'Left' and 'Right' buttons to set the highest upper limit tire temperature.
  5. After the setting is completed, long press the 'Menu' button to exit.
TPMS display showing temperature limit setting interface.
Setting interface for temperature limits.

4.5. Single Sensor Replacement (Pairing)

To replace a sensor, first remove the faulty sensor and then install the new sensor. For built-in sensors, professional installation is recommended.

  1. In standby mode, long press the 'Menu' key for 3 seconds to enter the system setting state.
  2. Press the 'Right' button five times to enter the pairing selection mode.
  3. Press the 'Menu' key once; the '0' number on the interface will flash, indicating the default front left wheel.
  4. Use the 'Left' and 'Right' keys to select the position of the sensor to be replaced (0 = front left, 1 = front right, 2 = rear left, 3 = rear right).
  5. After selecting the desired position, press the 'Menu' button. The number will flash.
  6. Install the new sensor on the tire. Observe the display for a change in the number.
  7. Once a change is detected, long press the 'Menu' button to exit.

Note: If it is a built-in sensor, inflate and deflate the tire when the number below flashes. During this pairing process, any sensor can be matched to any position.

TPMS display showing sensor pairing interface with tire positions and data.
Sensor pairing interface.

4.6. Restore Factory Settings (Re-pairing All Sensors)

  1. While the device is powered on, press and hold the middle button for 3 seconds to enter the settings.
  2. Press the 'Left' button to navigate to item 7.
  3. Press the middle button twice to reset the machine and restore factory settings. The system will then search for sensors again.
  4. To update the sensors, install the new sensors on the valves in order. Alternatively, drive the car at a speed of 30 km/h or more after resetting.
  5. After driving for approximately 10-30 minutes, the host will automatically search for sensor signals and wait for all 4 sensors to be found. Once all are found, pairing is complete.

After restoring factory settings, any previously manually set data will revert to the factory defaults.

TPMS display showing factory reset confirmation screen.
Factory reset confirmation screen.

5. Maintenance

5.1. External Sensor Battery Replacement

When replacing the battery of an external sensor, disassemble and install one by one. Do not mix or disassemble all at once. The external sensors use CR1632 button batteries, with a working temperature requirement of -30℃ to 80℃.

  1. Before disassembling the sensor, prepare a nut wrench. Turn the anti-theft nut clockwise to separate it from the sensor, then remove the sensor counter-clockwise.
  2. Use a wrench to unscrew the upper cover of the sensor in a counter-clockwise direction.
  3. Carefully remove the old battery from the battery holder and dispose of it according to environmental regulations.
  4. Distinguish the positive and negative positions (positive '+' facing upwards) and install a new CR1632 lithium battery.
  5. Screw on the upper cover of the sensor, and then use a wrench to tighten it clockwise.
Diagram showing the steps for external sensor battery replacement: removing gasket, wrenching shell, removing battery, and replacing with a new one.
External sensor battery exchange method.

5.2. Built-in Sensor Battery

Built-in sensors have a battery life of approximately 5 years. The batteries in built-in sensors are not replaceable and require professional installation for the sensor unit itself.

6. Troubleshooting

If you encounter issues with your TPMS, refer to the following common problems and solutions:

  • No pressure displayed after external sensor installation: Reinstall the sensor, ensuring it is tightened correctly and the anti-theft nut is secured.
  • Monitor does not turn on: Ensure the monitor is charged for 3-4 hours upon first receipt. If it still doesn't turn on, check the USB connection or solar exposure.
  • Inaccurate pressure readings: Ensure sensors are properly seated and calibrated. If minor discrepancies persist, consider performing a factory reset and re-pairing the sensors.
  • Sensors not pairing: Follow the single sensor replacement or factory reset procedures carefully. Ensure the monitor is on before installing sensors. Drive the vehicle above 30 km/h for 10-30 minutes after re-pairing to allow the system to detect all sensors.
  • Alarm sounds frequently: Check the set upper and lower pressure/temperature limits. Adjust them if they are too sensitive for your driving conditions.

7. Specifications

General Monitor Specifications

  • Voltage: 5V
  • Special Features: Solar Energy
  • External Testing Certification: CE
  • Certification: E-Mark
  • Item Type: Alarm Systems & Security
  • Origin: Mainland China
  • Display Dimensions: 9.4 cm (width) x 3 cm (height) [display part], 4 cm (total height with stand), 2 cm (stand height)
  • Charging Port: Micro USB

External Sensor Specifications (Model K07)

Table of external sensor specifications and a diagram showing its dimensions.
External Sensor Specifications and Dimensions.
ParameterValue
Working Voltage2.1-3.5V
Working Temperature-20℃-80℃
Pressure Accuracy±7KPA
Frequency433.92 MHz
Pressure Rate0KPA-400KPA
Temperature Rate-20℃-85℃
Temperature Accuracy+3℃
Battery Life2 Years, replaceable (CR1632)
Working Pressure0-3.5 Bar
Dimensions21mm (diameter) x 17mm (height)

Built-in Sensor Specifications (Model K07P)

Table of built-in sensor specifications and a diagram showing its dimensions.
Built-in Sensor Specifications and Dimensions.
ParameterValue
Working Pressure0-3.5 Bar
Working Voltage2.1-3.5V
Working Temperature-40℃-125℃
Pressure Accuracy±7KPA
Frequency433.92 MHz
Pressure Rate0KPA-400KPA
Temperature Rate-40℃-125℃
Temperature Accuracy+3℃
Battery Life5 Years, not replaceable
Dimensions53mm (width) x 78mm (height)

8. User Tips

  • Ensure sensors are correctly installed for accurate readings.
  • If you experience minor discrepancies in pressure readings, ensure sensors are properly seated and calibrated.
  • Upon receiving the TPMS, charge it for 3-4 hours to activate the battery, as it may have discharged during transit. It's normal if it doesn't turn on immediately.

9. Frequently Asked Questions (FAQ)

  • Are the internal sensors sold separately?
    Internal sensors are typically part of the system and may not be sold separately. Please contact support for replacement options.
  • Is this system suitable for campers? Does it detect at least 6 bars?
    The system's host setting range is 0.5 Bar - 6.0 Bar. Please check your camper's tire pressure requirements against this range to ensure compatibility.

10. Warranty and Support

For any technical assistance, warranty claims, or further inquiries, please contact Yantop Group directly using the information below:

  • Website: www.e-ace.cn
  • Email: fireking@e-ace.cn
  • Phone: +86 0755-8464 4084
  • WhatsApp: +86-18127083357
  • Address: Floor 2nd, No.1 Yuanxia street, Pingshan District, Shenzhen City, Guangdong Province, 518000, China

You can also refer to the official PDF user manual for more detailed instructions: User manual (PDF)

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.