1. Introduction
This manual provides comprehensive instructions for the JIKONG V19 JK-PB2A16S30P Smart Battery Management System (BMS). It covers the product overview, specifications, installation, operation, and maintenance procedures. Please read this manual thoroughly before installation and use to ensure safe and efficient operation of your battery system.
2. Safety Information
Working with battery systems involves electrical hazards. Always follow these safety guidelines:
- Ensure all connections are correct and secure before powering on the BMS. Incorrect wiring can lead to malfunction or damage.
- Do not attempt to modify or disassemble the BMS unless explicitly instructed.
- Wear appropriate personal protective equipment (PPE) when handling batteries and electrical components.
- Keep the BMS away from water, moisture, and flammable materials.
- In case of any abnormal behavior, disconnect the battery system immediately and consult the manufacturer or a qualified technician.
- Ensure proper ventilation around the battery system to prevent overheating.
3. Product Overview
3.1 BMS Overview
The JIKONG V19 Smart BMS is a management system designed for large-capacity series lithium battery packs. It features voltage acquisition, high-current active balancing, overcharge/over-discharge/overcurrent/over-temperature protection, coulomb metering, Bluetooth communication, and host computer monitoring. It is compatible with LiFePO4, ternary lithium, and lithium titanate battery types.
The BMS utilizes energy transfer active balancing technology, achieving a continuous balance current of 1A/2A. This technology ensures battery consistency, improves battery range, and extends battery life. It supports mobile APP (Android and iOS) and PC software for monitoring and parameter adjustment. The compact design, ease of operation, and comprehensive functions make it suitable for high-power energy storage, base station backup power, and solar power station battery PACKs.
3.2 Functional Characteristics
The JIKONG V19 BMS offers a wide range of features to ensure optimal battery performance and safety:
- LED Bluetooth Status Indicator: Provides visual feedback on Bluetooth connection status.
- APP Bluetooth Remote Operation: Control and monitor the BMS wirelessly via a mobile application.
- Battery Capacity Calculation: Accurately estimates and displays battery capacity.
- PC Software Support: Allows for advanced monitoring and parameter configuration via a computer.
- High Precision Voltage Acquisition (±3mV): Ensures accurate cell voltage measurements.
- High Precision Current Acquisition: Monitors charging and discharging currents with high accuracy.
- Information Screen Display Support: Compatible with external display screens for real-time data viewing.
- Accurate Time Logging: Records operational data with precise timestamps.
- RS485 Communication Support: Enables communication with inverters and other devices.
- CAN Communication Support: Facilitates integration into CAN-bus systems.
- Heating Function: Prevents battery performance degradation in low-temperature environments.
- Alarm Dry Contact Function: Provides outputs for external alarms or cooling fans based on trigger conditions.
- Charge Overcurrent Protection: Safeguards against excessive charging currents.
- Charge Overvoltage Protection: Prevents cells from being overcharged.
- Charge Over Temperature Protection: Protects the battery during charging from high temperatures.
- Low Temperature Protection During Charge: Prevents charging at dangerously low temperatures.
- Discharge Overcurrent Protection: Protects against excessive discharging currents.
- Discharge Undervoltage Protection: Prevents cells from being over-discharged.
- Discharge Over Temperature Protection: Protects the battery during discharging from high temperatures.
- Short Circuit Protection: Instantly cuts off current in case of a short circuit.
- Battery Parallel Current Limiting Function: Manages current flow when multiple battery packs are connected in parallel.
3.3 Structural Block Diagram
The structural block diagram illustrates the internal components and their interconnections within the BMS. It includes modules for active balancing, NTC temperature monitoring, isolated power supply, dry contacts, RS485, CAN, MCU, isolated communication, buzzer, reserved interfaces, EEROM, MOS drive, current limiting drive, MOS array, current limiting circuit, Bluetooth communication, LCD screen, and current sampling circuit.

4. Specifications
4.1 Product Parameters
The following table details the main technical parameters of the JIKONG V19 BMS:
| Parameter | Value | Unit |
|---|---|---|
| Supply Voltage | 20-70 | V |
| Standby Power Consumption | 12 | mW |
| Operating Power Consumption | 1100 | mW |
| Operating Temperature | -30 to 70 | °C |
| Max. Number of Collection Strings | 16 | S |
| Max. Balancing Current | 1 (JK-PB1A16S), 2 (JK-PB2A16S) | A |
| Max. Charging Current | 100 (10P), 150 (15P), 200 (20P) | A |
| Max. Discharge Current | 100 (10P), 150 (15P), 200 (20P) | A |
| Max. Instantaneous Current | 200 (10P), 300 (15P), 400 (20P) | A |
| Max. Internal Loop Resistance | 1 (10P), 0.45 (15P), 0.35 (20P) | mΩ |
| Protective Plate Size | 300*100*24 | mm |
| Finished Weight | 1000 | g |
4.2 Product Dimensions
The dimensions of the JK-PB1/2A16S-10/15/20P series protection board are 300mm x 100mm x 24mm.

4.3 Interface Board Dimensions
The interface board has specific dimensions to accommodate various connectors and switches. Refer to the detailed diagram for precise measurements.

5. Setup
5.1 Product Selection Guide
The JIKONG V19 BMS series (JK-PB1/2A16S-10/15/20P) is suitable for 7-16 series lithium battery packs. The specific model to choose depends on the battery type (Ternary Lithium, Lithium Iron, Lithium Titanate) and the number of adaptive battery strings.
| Product Model | Battery Type | Adaptive Battery Strings |
|---|---|---|
| JK-PB1A16S-10P | Ternary Lithium Battery | 7-16 |
| Lithium Iron Battery | 8-16 | |
| Lithium Titanate Battery | 14-16 | |
| JK-PB1A16S-15P | Ternary Lithium Battery | 7-16 |
| Lithium Iron Battery | 8-16 | |
| Lithium Titanate Battery | 14-16 | |
| JK-PB2A16S-15P | Ternary Lithium Battery | 7-16 |
| Lithium Iron Battery | 8-16 | |
| Lithium Titanate Battery | 14-16 | |
| JK-PB2A16S-20P | Ternary Lithium Battery | 7-16 |
| Lithium Iron Battery | 8-16 | |
| Lithium Titanate Battery | 14-16 |
5.2 Interface Definition
The BMS features various connectors and ports for different functions. Understanding their definitions is crucial for correct wiring.
- P1 (Cow-2.54-2*10P): Interface board connector.
- P2 (XH-2.54-6P): Interface board connector.
- P3 (HY-2.0-10P): Interface board connector.
- P4 (A1254WF-6A URAT Display Interface): Connects to the URAT display. Pins include K- (Activation signal negative), K+ (Activation signal positive), GND (Negative terminal), RX (UART RX, 5V), TX (UART TX, 5V), VCC (Display power output).
- P5 (A1254WF-6A Display Interface): Connects to the display. Pins include VCC (Display power output), A (RS485-A), B (RS485-B), GND (Negative terminal), K+ (Activation signal positive), K- (Activation signal negative).
- P6 (HY2.0-7P Acquisition Interface): Connects to NTC1 temperature probe and battery cell positive terminals (B0-B4 for 1st to 4th cells).
- P7 (HY2.0-6P Acquisition Interface): Connects to NTC2 temperature probe.
- P8 (HY2.0-7P Acquisition Interface): Connects to NTC3 temperature probe and battery cell positive terminals (B8-B12 for 9th to 12th cells).
- P9 (HY2.0-6P Acquisition Interface): Connects to NTC4 temperature probe and battery cell positive terminals (B13-B16 for 13th to 16th cells).
- P10 (M3 Screw Heating Interface): Connects to the heater element negative electrode (HT-).
- P11 (M3 Screw Power Input): Connects to the power input positive (B+).
- D1 (Bluetooth Connection Indicator): Steady ON when Bluetooth is connected, blinking when disconnected.
- P- (M6 Screw): Connects to external load or negative terminal of charger.
- B- (M6 Screw): Connects to the negative battery terminal.
5.3 Installation Method
The BMS is suitable for 7-16 series lithium battery packs. The wiring method varies depending on the number of cells. Always ensure correct connections to prevent damage.

5.4 Device Activation
Before powering on the protection board, double-check that the balance cables are properly connected and that P- and B- are correctly wired. Ensure the protection board is securely fixed to the battery pack. Incorrect connections can lead to abnormal operation or even damage.
The protection board is designed for charging activation. After assembling the battery, connect the charger (with voltage 2V higher than battery voltage) to activate the BMS. Alternatively, if you have a display screen and button, you can activate the device by inserting the cable into the display interface and pressing the button.
6. Operating Instructions
6.1 APP Installation
The mobile APP for the JIKONG BMS can be obtained by scanning the QR code below. An Android device with version 7 or higher is required.

6.2 Active Equalization
The BMS uses active equalization to transfer energy from high-voltage cells to low-voltage cells. To use this function, set basic battery parameters (number of cells, capacity, trigger equalization differential pressure, voltage calibration, current calibration) in the APP. The default balance current is 1A/2A. It is recommended that the balance current does not exceed 0.2C of the battery capacity. If not needed, the balancing function can be turned off in the APP's BMS control page.
6.3 Display Interface
The BMS has a reserved display interface. Users can connect an optional JIKONG display to view battery information conveniently. The display shows real-time data such as voltage, current, temperature, SOC, alarms, and cycle count.

6.4 Heating Function
The BMS includes a heating function to warm the battery in low temperatures using a resistance heater or heating film. This prevents reduced battery activity. The designed heating current is 10A. This function can be switched on/off via the APP. For safety, it is recommended to install a temperature control switch (45°C to 65°C, normally closed) in series with the heating circuit to prevent thermal runaway.6.5 Dry Contact Function
The BMS has two dry contacts to control external devices like alarms or fans. When the BMS detects conditions such as over-temperature, overcharge, or over-discharge, the dry contact status can switch to trigger an external buzzer or fan. Users can select two trigger conditions via the APP.

6.6 Communication Function
The BMS supports CAN and RS485 communication. The default CAN communication rate is 250K. Users can select the appropriate inverter communication protocol in the APP based on their inverter brand. There are two RS485 interfaces: RS485-1 for communication with inverters and other settings, and RS485-2 for parallel output and communication with the upper computer. The default baud rate is 115200. The communication address can be set using DIP switches (0-15).
6.7 Charge Current Limiting Function
The BMS includes a charge current limiting function. Users can set the continuous charging current (A), charging overcurrent delay (S), and charging overcurrent release time (S) in the APP. If the charging current exceeds the set limit, the current limiting function activates, maintaining the charging current at approximately 10A to protect the battery.6.8 Parallel Function
The parallel function allows simultaneous monitoring of multiple BMS units by a host computer via an RS485 bus. To use this, you need a USB to RS485 serial port cable and the JIKONG upper computer software. Each BMS must have a unique address (0-15), set via DIP switches. BMS with address 0 acts as the host, and others are slaves. The host BMS connects to the upper computer, and all BMS units are daisy-chained via RJ45 Ethernet cables using their RS485-2 ports.

6.9 Parameter Setting
Detailed parameter settings are available within the JIKONG mobile APP and PC software. Users can freely adjust multiple protection values such as overcharge, over-discharge, overcurrent, temperature, and balance. It is recommended to read the internal parameters of the protection board first before making changes.

7. Maintenance
The JIKONG V19 BMS incorporates several protection features to ensure the longevity and safety of your battery system. Regular monitoring via the APP or PC software is recommended.
- Overvoltage Protection (Charge/Discharge): The BMS will stop charging if any cell exceeds the set overcharge voltage and resume when all cells are below the recovery voltage. Similarly, it protects against over-discharge.
- Overcurrent Protection (Charge/Discharge): If charging or discharging current exceeds the set limit for a specified delay, the BMS will interrupt the current flow and resume after the recovery time.
- Overtemperature Protection (Charge/Discharge): The BMS will stop charging/discharging if the temperature exceeds the set limit and resume when it falls below the recovery temperature.
- Low Temperature Protection (Charge): Charging is prevented if the temperature drops below the set low-temperature limit and resumes when it rises above the recovery temperature. For extremely cold areas, using the heating function is recommended.
- Short Circuit Protection: In the event of a short circuit, the BMS will immediately cut off the current. Short circuit protection delay and recovery time can be adjusted via the APP.
- Emergency Switch: In case of critical issues (over-temperature, over-discharge, overcharge, string drop), activating the emergency switch via the APP will enable charge and discharge for 30 minutes, providing a temporary operational window.
- Intelligent Sleep: This function puts the BMS into a low-power sleep mode if the charging/discharging current is less than 1A for 26 consecutive hours. It can be reactivated by pressing a button or connecting a charger.
8. Troubleshooting
If you encounter any issues with your JIKONG V19 BMS, refer to the following general troubleshooting steps:
- No Power/No Display: Check all power connections (B+, B-, P-), ensure the battery is activated, and verify the display cable connection.
- BMS Not Communicating: Ensure Bluetooth is enabled on your mobile device or that the RS485/CAN connections to the PC are secure. Check DIP switch settings for correct addressing in parallel setups.
- Protection Triggered (e.g., Overvoltage, Overcurrent): Review the real-time data in the APP to identify which protection was triggered. Check individual cell voltages, current draw, and temperature. Adjust parameters in the APP if necessary, but always understand the implications of such changes.
- Balancing Not Working: Verify that active equalization is enabled in the APP and that the trigger differential pressure is set correctly. Ensure all balance cables are properly connected.
- Heating Function Not Working: Check if the heating function is enabled in the APP and if the external temperature is below the set threshold. Inspect the heating element connections.
For more detailed troubleshooting and error codes, consult the JIKONG mobile APP or PC software's logging and alarm sections.
9. User Tips
- Regular Monitoring: Periodically check the battery status and BMS parameters using the mobile APP or PC software to ensure optimal performance and detect potential issues early.
- Parameter Adjustment: While the BMS offers extensive parameter customization, exercise caution when modifying default settings. Always understand the impact of changes on battery safety and longevity.
- Firmware Updates: Check the official JIKONG website or APP for any available firmware updates to ensure your BMS has the latest features and bug fixes.
- Clean Connections: Ensure all wiring connections are clean and tight to prevent resistance and potential hotspots.
- Environmental Considerations: Operate the BMS within its specified temperature range. Utilize the heating function in cold environments and ensure adequate ventilation in hot environments.
10. Warranty and Support
For warranty information, technical support, and service inquiries, please contact JIKONG BMS Global Store directly or refer to the official product documentation available on their website. Keep your purchase records for warranty claims.
A user manual PDF is available for download from the seller's site: JIKONG BMS User Manual (PDF)