1. Introduction
This manual provides detailed instructions for the Estardyn 2.4 inch TFT LCD Screen Module, model GMT024-08-SPI8P. This module features a 2.4-inch TFT display with a resolution of 240x320 pixels, driven by an ST7789 controller, and communicates via a 4-wire SPI interface. It is designed for integration into various embedded systems and DIY projects, offering vibrant color display capabilities.
2. Specifications
The following table outlines the key technical specifications of the 2.4 inch TFT LCD module:
| Feature | Specification |
|---|---|
| Model Number | GMT024-08-SPI8P (2.4 inch TFT SPI LCD) |
| Display Mode | 320*240 (Resolution) |
| Type | TFT/IPS |
| Resolution | 240*RGB*320 pixels |
| Color Depth | Full color 65K/262K |
| Polarization Mode | Transmissive / Positive |
| Interface Voltage | 3.3V |
| Backlight Voltage | VDD/3.0V Typical |
| Backlight Current (IF) | 80mA (15mA/LED) |
| Operating Temperature | -20°C to 70°C |
| Storage Temperature | -30°C to 80°C |
| Driver IC | ST7789 or Compatible |
| Interface | 4-wire SPI (10-pin FPC cable) |
| Module Dimensions (L x W x H) | 46.9mm x 71mm x 13.5mm (MAX) |
| Active Area (L x W) | 37.42mm x 49.66mm |

3. Setup and Wiring
The Estardyn 2.4 inch TFT LCD module uses a 4-wire SPI interface for communication. Proper wiring to your microcontroller is essential for correct operation. Refer to the pinout diagram below for connections.

3.1 Pin Description
| Pin | Description |
|---|---|
| GND | Ground connection. |
| VCC | Power supply (3.3V). |
| SCL | Serial Clock for SPI communication. |
| SDA | Serial Data (MOSI) for SPI communication. |
| RST | Reset pin. Active low. |
| DC | Data/Command selection pin. High for data, low for command. |
| CS | Chip Select pin. Active low. |
| BL | Backlight control pin. Typically connected to VCC for always-on backlight, or to a PWM pin for brightness control. |
3.2 Connection Steps
- Ensure your microcontroller operates at 3.3V logic levels. If using a 5V microcontroller, a logic level shifter is required for all data pins (SCL, SDA, RST, DC, CS) to prevent damage to the LCD module.
- Connect the GND pin of the LCD module to the Ground of your microcontroller.
- Connect the VCC pin of the LCD module to the 3.3V power supply of your microcontroller.
- Connect the SCL (Serial Clock) pin to your microcontroller's SPI clock pin (e.g., SCK on Arduino, ESP32).
- Connect the SDA (Serial Data) pin to your microcontroller's SPI MOSI (Master Out Slave In) pin.
- Connect the RST (Reset) pin to a digital output pin on your microcontroller.
- Connect the DC (Data/Command) pin to a digital output pin on your microcontroller.
- Connect the CS (Chip Select) pin to a digital output pin on your microcontroller.
- Connect the BL (Backlight) pin to VCC for continuous backlight, or to a PWM-capable digital output pin for brightness control.

4. Operating Instructions
To operate the Estardyn 2.4 inch TFT LCD module, you will need to use a compatible library for the ST7789 driver IC with your chosen microcontroller platform (e.g., Arduino, ESP32, Raspberry Pi).
4.1 Software Setup (Example for Arduino IDE)
- Install Arduino IDE: If not already installed, download and install the Arduino IDE from the official website.
- Install Board Support: Add support for your specific microcontroller board (e.g., ESP32, ESP8266) via the Board Manager in the Arduino IDE.
- Install Libraries:
- Open the Arduino IDE. Go to
Sketch > Include Library > Manage Libraries.... - Search for "TFT_eSPI" and install the library by Bodmer. This library is highly optimized and widely used for ST7789 displays.
- You may also need to install a graphics library like "Adafruit GFX Library" if not already installed, as TFT_eSPI often depends on it.
- Open the Arduino IDE. Go to
- Configure TFT_eSPI:
- Navigate to the
TFT_eSPIlibrary folder (usually inDocuments/Arduino/libraries/TFT_eSPI). - Open the
User_Setup.hfile. - Uncomment the line
#define ST7789_DRIVERto select the correct display driver. - Configure the display resolution:
#define TFT_WIDTH 240and#define TFT_HEIGHT 320. - Define your connected SPI pins (SCL, SDA, RST, DC, CS, BL) according to your microcontroller's pin assignments. For example:
#define TFT_MOSI 23 // SDA #define TFT_SCLK 18 // SCL #define TFT_CS 15 // Chip select control pin #define TFT_DC 2 // Data Command control pin #define TFT_RST 4 // Reset pin (could be set to -1 and display will be reset by software) #define TFT_BL 27 // LED back-lightNote: Pin numbers are examples; adjust them to your specific wiring. - Save the
User_Setup.hfile.
- Navigate to the
- Upload Example Code:
- Open an example sketch from the
TFT_eSPIlibrary (e.g.,TFT_Graphic_Test). - Compile and upload the sketch to your microcontroller.
- Open an example sketch from the
4.2 Basic Display Functions
Once the library is set up, you can use its functions to draw text, shapes, and images on the display. Common functions include:
tft.init(): Initializes the display.tft.fillScreen(color): Fills the entire screen with a specified color.tft.drawString(text, x, y): Draws text at a specified coordinate.tft.drawRect(x, y, w, h, color): Draws a rectangle.tft.fillRect(x, y, w, h, color): Draws a filled rectangle.tft.drawPixel(x, y, color): Draws a single pixel.tft.setRotation(rotation): Sets the screen orientation (0-3).
5. Maintenance
The Estardyn TFT LCD module is a robust component, but proper care can extend its lifespan and ensure optimal performance:
- Cleaning: Use a soft, lint-free cloth, slightly dampened with water or a mild screen cleaner, to gently wipe the display surface. Avoid harsh chemicals, abrasive materials, or excessive pressure.
- Handling: Avoid touching the display surface directly with bare hands to prevent fingerprints and smudges. Handle the module by its edges.
- Storage: When not in use, store the module in an anti-static bag in a cool, dry place, away from direct sunlight and extreme temperatures.
- Power: Always ensure the correct voltage (3.3V) is supplied to the VCC pin. Incorrect voltage can damage the module.
- ESD Protection: LCD modules are sensitive to electrostatic discharge (ESD). Take appropriate ESD precautions when handling the module.
6. Troubleshooting
If you encounter issues with your Estardyn TFT LCD module, refer to the following common troubleshooting steps:
- No Display / Blank Screen:
- Check all wiring connections, especially VCC, GND, SCL, SDA, RST, DC, and CS. Ensure they are secure and connected to the correct pins on your microcontroller.
- Verify that the power supply to VCC is 3.3V.
- Ensure the backlight (BL) pin is correctly powered (e.g., connected to VCC or a high digital pin).
- Confirm that the
User_Setup.hfile in your TFT_eSPI library is correctly configured for the ST7789 driver and your specific pin assignments. - If using a 5V microcontroller, ensure logic level shifters are correctly implemented.
- Try a different example sketch to rule out software issues.
- Incorrect Colors / Distorted Display:
- Double-check the
TFT_WIDTHandTFT_HEIGHTdefinitions inUser_Setup.h. The resolution is 240x320. - Ensure the correct driver (
ST7789_DRIVER) is uncommented inUser_Setup.h. - Verify SPI clock speed settings. Sometimes, reducing the SPI clock speed can resolve data corruption issues.
- Check for loose connections on the data lines (SCL, SDA).
- Double-check the
- Module Not Responding:
- Ensure the RST pin is correctly toggled during initialization by the library or your code.
- Verify that the CS (Chip Select) pin is correctly controlled by your software.
7. User Tips
- Library Compatibility: Many users have found success with the
TFT_eSPIlibrary for Arduino and ESP32 platforms due to its optimization and support for the ST7789 driver. - Power Supply: While the module operates at 3.3V, ensure your power supply can provide sufficient current, especially for the backlight, which can draw up to 80mA.
- Orientation: Experiment with the
setRotation()function in your code to find the optimal display orientation for your project.
8. Warranty and Support
For technical assistance, driver updates, or further inquiries, please refer to the official Estardyn support channels or the product page where you purchased the module. Keep your purchase records for any warranty claims.