DUMBORC FZD

Contents

DUMBORC FZD RC Car Simulation Light Controller 12 LED System Kit

Model: FZD

1. Introduction

This manual provides instructions for the DUMBORC FZD RC Car Simulation Light Controller 12 LED System Kit. This system is designed to add realistic lighting effects to 1/10 and 1/8 scale RC cars, including on-road trucks, drift cars, and models like TAMIYA CC01 and Axial SCX10. It features a light controller and a 12-LED light set, offering various lighting functions and low voltage alarm capabilities.

2. Package Contents

  • 1 x DUMBORC FZD Light Controller
  • 1 x 12-LED Light Set (pre-wired)
  • Connection cables
DUMBORC FZD RC Car Simulation Light Controller 12 LED System Kit with LEDs and example RC car
Overview of the DUMBORC FZD RC Car Simulation Light Controller and 12 LED System Kit components.

3. Setup and Installation

3.1. FZD Light Controller Connections

The FZD Light Controller serves as the central unit for managing the LED lights. Connect the various components as described below:

  • CH2: Electrically modulated signal line (6V output, supports high voltage).
  • CH3: Enable/disable control signal.
  • LED: Connect to headlights (5V output).
  • M1: Coupling motor.
  • BUZ: Beep (low voltage signal).
  • Power: Connect to the main battery.
DUMBORC FZD Light Controller with labeled ports for CH1, CH2, CH3, LED, M1, BUZ, and Power
Close-up view of the FZD Light Controller showing its various connection ports.
DUMBORC FZD Light Controller with all wires connected to the ports
The FZD Light Controller with all necessary wires connected, illustrating a typical setup.

3.2. 12-LED Light Set Identification

The 12-LED light set includes various types of lights for different functions:

  • CL (Cornering Lamp): 4 Yellow LEDs
  • FL (Flash Light): 2 Blue LEDs
  • DRL (Daytime Running Light): 4 White LEDs
  • SL (Stop Lamp): 2 Red LEDs
Close-up of LED wires with labels for Cornering Lamp (Yellow), Flash Light (Blue), Daytime Running Light (White), and Stop Lamp (Red)
Identification of the different LED types and their corresponding colors and functions.
The complete 12 LED light set with various colored LEDs and wiring
The full 12-LED light set, ready for installation into your RC vehicle.

3.3. Wiring Diagram and Control Modes

The controller supports both 4-channel and 2-channel control modes, with specific functions assigned to the blue button and mode display light.

Detailed wiring diagram for 4-CH and 2-CH control modes, including blue button functions and mode display light indicators
Comprehensive wiring diagram and control instructions for both 4-channel and 2-channel setups.

Blue Light Button Functions:

  • Short press once: Switches between brake and reversing light forward/reversing linkage control.
  • Short press twice: Switches to emergency light and headlight control by hand.
  • Press for 3 seconds: Switches to headlight, reversing light, and throttle linkage for 'super mode'.

Mode Display Light:

  • Green light: Headlights and emergency lights are controlled by a 3-way switch.
  • Red light: Headlights and emergency lights are controlled by the handwheel.

4-Channel Control Mode (Factory Default):

If your receiver has more than 4 channels, this is the default setting. The mode light will be green. Functions are as follows:

  • Channel 1: Controls turn signals.
  • Channel 2: Controls brake and reverse lights.
  • Channel 3: Controls emergency lights.
  • Channel 4: Controls headlights, warning, and flashing lights.
  • 1CH handwheel: Push forward to control the left turn light.

2-Channel Control Mode:

For 2-channel receivers, press the blue button twice to switch to one-hand handwheel control. The mode light will be red. Functions are as follows:

  • Control headlight by pushing the handwheel 2 times.
  • Control emergency light by pushing the handwheel 3 times forward.
  • Control ambient light by pushing the handwheel 4 times forward.

4. Operating Instructions

4.1. Light Control

Once the system is connected and powered on, use your RC transmitter to control the lights according to the selected control mode (4-channel or 2-channel handwheel mode). Refer to the 'Wiring Diagram and Control Modes' section for specific control inputs.

4.2. Low Voltage Alarm

The controller automatically identifies 2S or 3S batteries. The default alarm voltage for 2S batteries is 7.2V, and for 3S batteries, it is 10.7V. When the battery voltage drops below the alarm threshold, the BUZ (beep) will sound to indicate low voltage.

5. Maintenance

  • Keep the controller and LEDs clean and free from dust and debris.
  • Avoid exposing the components to excessive moisture or extreme temperatures.
  • Regularly check all connections to ensure they are secure.
  • Do not attempt to modify the wiring or components, as this may damage the system and void any potential support.

6. Troubleshooting

6.1. Lights Not Functioning

  • Check Power: Ensure the controller is properly connected to the battery and receiving power.
  • Verify Connections: Confirm all LED wires are correctly plugged into the controller and the controller is connected to the receiver.
  • Confirm Control Mode: Ensure the controller is in the correct 4-channel or 2-channel mode for your transmitter setup.
  • Transmitter Settings: Check your transmitter's CH1 neutral fine-tuning and EPA settings. For optimal performance, use default neutral fine-tuning at 0 and maximum EPA settings for CH1 and CH2.

6.2. Low Voltage Alarm Issues

  • Battery Type: Ensure the controller correctly identifies your 2S or 3S battery.
  • Battery Condition: Check your battery's charge level and overall health.

6.3. Light Operation Delay

  • EPA Settings: For normal mode, 3CH and 4CH EPA settings can be used up to 25%. Smaller settings reduce delay, larger settings increase delay. A 4-second delay may occur when turning off lights after settings are complete.
  • Handwheel Speed: When activating ambient lights via handwheel, avoid pushing too fast or too slow. A consistent, moderate speed is recommended for proper activation.

7. Specifications

ComponentSpecification
FZD Light Controller
Item Size35 x 21 x 13 mm
Item Weight11g
12-LED Light Set
MaterialPlastics
Number of LED Bulbs12
Input Voltage4.8V - 6.0V
Working Current100mA
LED Colors & Quantity4x Yellow (Cornering), 2x Blue (Flash), 4x White (DRL), 2x Red (Stop)
Lamp Bead Diameter2x 5mm (headlights), 10x 3mm (rest)
Total Wire Length (per light)410mm
Suitable for1/10 RC Cars

8. User Tips

  • Always test your connections and light functions before fully assembling your RC car to ensure everything is working as expected.
  • When installing the LEDs, ensure wires are routed safely and do not interfere with moving parts of the RC vehicle.

9. Warranty and Support

If you encounter any product problems, please contact the seller or manufacturer directly. Be prepared to provide product pictures or videos to assist with troubleshooting and support. Your satisfaction with the product and service is important.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.