1. Introduction
Thank you for using the Viladepot MIG200 welder. This manual provides essential information for safe and effective operation. Please read it thoroughly before use.
The Viladepot MIG200 is an Inverter MIG welding machine that combines three functions: MIG, Lift TIG, and MMA. It is suitable for welding various materials such as carbon steel, stainless steel, copper, and titanium.
Key Features:
- 3-in-1 Functionality: Offers MIG, Lift TIG, and MMA welding modes.
- Advanced Technology: Utilizes IGBT high-frequency soft switch transform for high efficiency, compact size, and portability.
- Enhanced Performance: Advanced control system significantly improves welding performance to meet diverse process requirements.
- User-Friendly: Features easy arc starting, stable arc, and high performance.
- Quality Welds: Delivers small spatter, stable current, high reliability, and good weld-seam shaping.

2. Safety Precautions
Always prioritize safety. Failure to follow these precautions may result in serious injury or death.
2.1 General Safety Precautions
- Ensure to follow all precautions specified in this manual.
- Input power supply, installation site selection, and high-pressure gas use must comply with relevant standards and rules.
- Only qualified personnel are permitted to install, overhaul, maintain, and operate the welding machine. Irrelevant personnel must not enter the welding workplace.
- Do not use the welding machine for purposes other than welding (e.g., charging, heating, pipeline unfreezing).
- Avoid placing the welding machine on uneven ground to prevent tipping.
2.2 Avoid Electrical Shock or Burn
- Touching live electrical parts is strictly forbidden.
- Ensure the welding machine is properly grounded by a professional electrician using a copper conductor of specific cross-section.
- The power source connection to the welding machine must be done by a professional electrician with appropriate copper conductors. Ensure insulating sheaths are undamaged.
- Insulate your body and the base metal when working in wet or restricted areas.
- Use a safety net when working at heights.
- Close the input power when the machine is not in use.
2.3 Avoid Welding Fume and Gas Damaging Human Body
- Use specified exhaust equipment to prevent gas poisoning and suffocation.
- Protective gas can accumulate at the bottom of containers, causing suffocation. Ensure adequate ventilation.
2.4 Avoid Welding Arc, Splash, and Welding Slag Damaging Human Body
- Wear protective glasses with sufficient shade. The welding arc can cause ocular inflammation, and splashes/slag can burn eyes.
- Use appropriate protective gear for welding, including leather gloves, caftan, cap, welding spats, and apron, to protect against arc light, splashes, and slag burns.
2.5 Avoid Fire, Explosion, and Other Accidents
- Ensure no combustibles are present in the welding area, as splashes and hot weld joints can cause fires.
- Cables and base metal must be firmly connected to prevent overheating and potential fires.
- Do not weld in the presence of combustible gases or in containers that held combustibles, as this may lead to explosions.
- Always have a fire extinguisher readily available.
2.6 Prevent Injury from Rotating Moving Parts
- Keep fingers, hair, and clothing away from the cooling fan, wire feed roll, and other rotating parts.
- When feeding wire, keep the welding gun end away from your eyes, face, and body to prevent injury from the wire.
2.7 Avoid Falling Gas Cylinder and Breaking Gas Regulator
- Gas cylinders must be reliably fixed to prevent them from falling and causing injury.
- Do not store gas cylinders in high-temperature areas or direct sunlight.
- When opening the gas cylinder valve, keep your face away from the gas outlet to avoid injury from high-pressure gas.
- Use the gas regulator provided by the manufacturer and follow its usage regulations.
2.8 Prevent Movement of Welding Machine
- Do not stand under the welding machine when it is being moved.
- If moving with a forklift or crane, ensure the welding machine is secure to prevent falling.
- Rope slings must be strong enough and the angle between the sling and hook should not exceed 30°.
2.9 Precautions for Electromagnetic Compatibility
Welding equipment can cause electromagnetic interference. Minimize emissions through proper installation and application.
- The MIG200 is Class A equipment, not suitable for residential areas powered by public electrical systems due to potential conduction and radiated interference.
- Environment Assessment: Before installation, assess potential electromagnetic disturbances to other equipment (power cables, control cables, signals, telephone wires, broadcasting equipment, computers, industrial protective equipment, medical devices like pacemakers).
- Reducing Radiation: Connect to public power supply as recommended, use filters if interference occurs. Shield power cables with metal pipes. Perform routine maintenance, keep all inlets/panels closed, do not modify the equipment unless specified in the manual. Keep welding cables as short and close to each other as possible.
- Equipotential Lapping: Be aware of metal objects in the surroundings. Insulate yourself from metal objects and electrodes to prevent electrical shock.
- Workpiece Earthing: Earthing the workpiece can reduce radiation but may increase electric shock risk. Ensure proper grounding without increasing risk.
- Shielding: Shield surrounding equipment and cables to reduce electromagnetic interference.
3. Specifications
3.1 Main Technical Parameters
| Parameter | AC110V±15%, 50/60Hz | AC220V±15%, 50/60Hz | ||
|---|---|---|---|---|
| MIG | MMA | MIG | MMA | |
| Rated Input Power (KVA) | 4.6 | 5.6 | 4.6 | 5.6 |
| Rated Input Current (A) | 42 | 50 | 21 | 25 |
| No-load Voltage (V) | 56V±5 | |||
| Output Current (A) | 20-120 | 20-120 | 20-200 | 20-200 |
| Output Voltage (V) | 15-20 | 20.8-24.8 | 15-21 | 20.8-24.8 |
| Wire Diameter (mm) | Gasless flux cored wire 0.8-1.0 (1KG) | |||
| Rated Duty Cycle (%) | 60 | |||
| Efficiency (%) | 70 | |||
| Insulation Grade | F | |||
| Protection Grade | IP21 | |||
| Weight (Kg) | 6.1kg | |||
| Dimensions (cm) | 35*25*25cm | |||
3.2 Included Accessories

- 1 x MIG Welding Machine
- 1 x 3M 14AK MIG Torch
- 1 x Helmet
- 1 x Brush
- 1 x 2M Welding Holder
- 1 x 2M Ground Clamp
- 2 x Gas Nozzle
- 2 x Nozzle Holder
- 5 x 0.8mm Contact Tips
- 1 x 0.8MM 0.5KG Flux-Cored Wire
- 1 x User Manual
4. Setup
4.1 Environmental Requirements
- Install in a dry environment with humidity less than 90% at 20°C and 50% at 40°C.
- Operating temperature range: -10°C to 40°C. Storage/transportation temperature: -20°C to 55°C.
- Shelter the machine from direct sunlight and rain.
- Avoid using in environments with strong airflow when TIG welding.
- The inclination of the welding power should be less than 10°, and altitude no more than 1000m.
- Avoid dusty, acidic, or corrosive environments.
- Maintain at least 20cm clearance from walls and 10cm from other welding machines.
4.2 Power Source Requirements
- Waveform: Standard pure sine wave.
- Fluctuation range: 220V±15%.
- The power supply should be single-phase AC 220V/50Hz. Use a distribution cabinet with an automatic air switch and ensure safe grounding.
- Connect the welding input power wire to the corresponding voltage level and a ≥60A circuit breaker.
- Ensure good contact for the input power wire to prevent oxidation.
- Use a multimeter to verify the input voltage is within the fluctuation range.
- Connect the yellow-green wire on the power cable to the grounding screw on the rear panel (≥4Ω wire) and ensure good ground connection.
4.3 General Connection Instructions
Before any electrical connection, turn off the power switch of the distribution panel. The equipment protection level is IP21; avoid using in rain.

4.4 Flux MIG (No Gas) Connection
- Connect the earth clamp to the negative pole and the feeder cable to the positive pole.
- Open the wire compartment. The wire feed wheel default is 1.0mm. If using 0.8mm wire, remember to flip the wire feed wheel to the 0.8mm side.
- Place the flux-cored wire spool onto the spindle and secure it with the spool lock and spacer.
- Thread the wire through the wire feed wheel and into the MIG torch liner. Adjust the wire pressing wheel to apply enough pressure to feed the wire without slipping, but do not over-press to avoid deforming the wire.
- Feed the wire out through the MIG torch. Select the appropriate contact tip for the wire diameter and tighten it.

4.5 Lift TIG Connection
- Connect the gas pipe of the TIG torch to the gas cylinder (if using shielding gas, though Lift TIG can be done without).
- Connect the separated type TIG torch to the negative socket.
- Connect the earth clamp to the positive socket.
4.6 MMA (Stick) Connection
- Connect the welding cable (electrode holder) to the machine.
- For DC EP (Electrode Positive): Connect the electrode holder to the positive (+) terminal and the workpiece clamp to the negative (-) terminal.
- For DC EN (Electrode Negative): Connect the electrode holder to the negative (-) terminal and the workpiece clamp to the positive (+) terminal.
The operator can choose the connection method based on the base metal and electrode material. Generally, alkaline electrodes are recommended with DC reverse connection (DC EP).

5. Operation
5.1 Front Panel Controls

- Digital Display: Shows welding parameters.
- Voltage Regulation (V): Adjusts welding voltage. (Screen not displayed for this function).
- Current Regulation (A): Adjusts welding current.
- Function Selection Button: Used to select between Lift TIG, MMA, and Gasless Flux Cored Wire (0.8mm/1.0mm).
- O.C. Indicator Light: Illuminates for over-temperature or abnormal conditions.
5.2 Operating Modes
Flux MIG (No Gas) Welding:
- Select the Flux Cored Wire mode (0.8 or 1.0) using the function selection button.
- Adjust the current (A) and fine-tune the voltage (V) using the respective knobs.
- Begin welding.
Lift TIG Welding:
- Select the Lift TIG mode using the function selection button.
- Adjust the current (A) using the knob.
- To start the arc, contact the tungsten electrode to the workpiece, then lift the torch slightly at the moment the arc initiates.
- There is no control switch for gas flow and current. Turn off the gas cylinder and keep the torch away from the workpiece to avoid waste and for safety.
MMA (Stick) Welding:
- Select the MMA mode using the function selection button.
- Adjust the current (A) using the knob.
- Begin welding with the electrode.
5.3 Welding Parameter Tables (Reference)
MMA Welding Process (Low Carbon Steel)
| Electrode Diameter (mm) | Recommended Welding Current (A) | Recommended Welding Voltage (V) |
|---|---|---|
| 1.0 | 20-60 | 20.8-22.4 |
| 1.6 | 44-84 | 21.76-23.36 |
| 2.0 | 60-100 | 22.4-24.0 |
| 2.5 | 80-120 | 23.2-24.8 |
| 3.2 | 108-150 | 23.32-24.92 |
Note: This table is suitable for low carbon steel welding. Refer to relevant material and process manuals for other materials.
Titanium and Alloy-TIG Parameter
| Thickness (mm) | Groove Shape | Welding Layer | Tungsten Diameter (mm) | Wire Diameter (mm) | Current (A) | Argon Gas Volume (L/min) | Nozzle Diameter (mm) | ||
|---|---|---|---|---|---|---|---|---|---|
| 0.5 | 1 | 1.5 | 1.0 | 30-50 | 8-10 | 6-8 | 14-16 | 10 | |
| 1.0 | I-shape | 1 | 2.0 | 1.0-2.0 | 40-60 | 8-10 | 6-8 | 14-16 | 10 |
| 1.5 | 1 | 2.0 | 1.0-2.0 | 60-80 | 10-12 | 8-10 | 14-16 | 10-12 | |
| 2.0 | 1 | 2.0-3.0 | 1.0-2.0 | 80-110 | 12-14 | 10-12 | 16-20 | 12-14 | |
| 2.5 | 1 | 2.0-3.0 | 2.0 | 110-120 | 12-14 | 10-12 | 16-20 | 12-14 | |
| 3.0 | 1-2 | 3.0 | 2.0-3.0 | 120-140 | 12-14 | 10-12 | 16-20 | 14-18 | |
| 4.0 | Y-shape | 2 | 3.0-4.0 | 2.0-3.0 | 130-150 | 14-16 | 12-14 | 20-25 | 18-20 |
| 5.0 | 2-3 | 4.0 | 3.0 | 130-150 | 14-16 | 12-14 | 20-25 | 18-20 | |
| 6.0 | 2-3 | 4.0 | 3.0-4.0 | 140-180 | 14-16 | 12-14 | 25-28 | 20-22 | |
| 7.0 | 2-3 | 4.0 | 3.0-4.0 | 140-180 | 14-16 | 12-14 | 25-28 | 20-22 | |
| 8.0 | 3-4 | 4.0 | 3.0-4.0 | 140-180 | 14-16 | 12-14 | 25-28 | 20-22 |
Thin Stainless Steel Sheet—TIG Parameter
| Thickness (mm) | Joint Type | Tungsten Diameter (mm) | Wire Diameter (mm) | Current Type | Current (A) | Argon Gas Volume (L/min) | Speed (cm/min) |
|---|---|---|---|---|---|---|---|
| 1.0 | butt | 2 | 1.6 | DCEN | 7-28 | 3-4 | 12-47 |
| 1.2 | butt | 2 | 1.6 | DCEN | 15 | 3-4 | 25 |
| 1.5 | butt | 2 | 1.6 | DCEN | 5-19 | 3-4 | 8-32 |
6. Maintenance
Warning: All maintenance, service, and cleaning work must be performed with the power removed. Ensure the power cord is unplugged before opening the casing.
6.1 Safety Points for Maintenance
- Good Ventilation: Ensure the ventilation area is not covered or blocked, and maintain at least 0.3 meters distance from surrounding objects.
- Avoid Overload: Operate the welder within its allowable load duration (duty cycle) to prevent damage and shorten its lifespan.
- Forbidden High Voltage: Do not exceed the specified power supply voltage, as this will damage the welder.
- Proper Grounding: Ensure the welding machine is reliably grounded to release static electricity and prevent leakage.
6.2 General Maintenance Procedures
- Dedust Regularly: Use dry, clean compressed air to clean the system. Dedust daily if operating in smoky or severely polluted conditions. Ensure compressed air is at the required pressure to avoid damaging internal components.
- Check Connections: Inspect internal contact areas for tight connections (especially plug-in joints or components). Reinforce any loose contacts. If rust or oxidation occurs, use sandpaper to remove the oxide film and reconnect.
- Avoid Moisture: Prevent water and moisture penetration. If this occurs, dry the inside of the welder and perform a megger insulation test between connection joints, and between joints and casing. Resume operation only if no error is detected.
- Storage: If the welder is not used for a long period, seal it in its original packaging and store it in a dry condition.
6.3 Before Maintenance
Warning: Blind experiments and imprudent overhauls can lead to expanded failures and difficulties in formal maintenance. Electronic equipment with exposed live parts can be dangerous. Any direct or indirect contact can lead to electric shocks, and severe electric shock can cause death!!!
Attention: During the warranty period, if any fault of the welding power source is due to incorrect maintenance not authorized by the company, the suppliers will not provide free repairs.
7. Troubleshooting
- O.C. Indicator Light On (Overheat): If the machine is protected due to over-temperature, the O.C. indicator light will be on. Do not unplug the power supply; allow the cooling fan to continue running to cool the welder. Welding can resume once the light turns off and the temperature drops to the standard range.
- O.C. Indicator Light On (Overcurrent): If the O.C. indicator light is on due to overcurrent, some components may be damaged. Restart the machine after checking for issues. If the issue persists, contact technical support.
- Welder Stops Working: If the welding machine exceeds the standard load duration, it may enter a protection state and stop working. Allow it to cool down as described for overheat protection.
- Wire Feeding Issues: If the wire is distorted or not feeding normally, check the wire pressing wheel adjustment. Ensure it's not too tight or too loose.
- Current/Voltage Mismatch: If the current and voltage are not well matched, try fine-tuning the voltage.
8. User Tips
- Warranty Information: For details regarding the product warranty, it is recommended to directly contact the seller or refer to the specific warranty documentation provided with your purchase.
9. Warranty and Support
For warranty information and technical support, please contact your retailer or the manufacturer directly. Unauthorized maintenance during the warranty period may void the warranty.
A PDF version of this user manual is available for download: User Manual (PDF)