1. Introduction
The HGLRC C1 Remote Controller is an entry-level, high-value handle control designed for RC airplanes and FPV drones. It features a built-in 500mW ELRS 2.4G TX module, offering stable signal transmission and extended control distance. This controller simplifies operations like frequency pairing, power adjustment, and joystick calibration, making it user-friendly for beginners and experienced pilots alike. It supports multiple simulators and can be expanded with an external NANO TX module.
2. Safety Information
Please read and understand all safety instructions before operating the HGLRC C1 Remote Controller. Failure to follow these instructions may result in injury, damage to the product, or damage to property.
- Always operate your RC aircraft in open areas, away from people, animals, and obstacles.
- Ensure the controller and aircraft batteries are fully charged before each use.
- Never operate the controller in adverse weather conditions (e.g., strong winds, rain).
- Keep the controller away from water and moisture.
- Do not attempt to modify or disassemble the controller. Repairs should only be performed by authorized service personnel.
- Store the controller in a cool, dry place when not in use.
- Dispose of batteries according to local regulations.
3. Package Contents
Verify that all items are present in your package:
- 1x HGLRC C1 Remote Controller
- 1x Remote Control Hanging Strap
- 1x USB-C Data Cable
- 1x Wireless Dongle (Optional, depending on purchased version)
4. Product Overview
The HGLRC C1 Remote Controller is designed for intuitive control and ease of use. Key features include:
- Built-in ELRS 2.4G TX Module: 500mW output power with a built-in antenna for reliable long-range communication.
- Simplified Operation: Direct controls for frequency pairing, power adjustment, and joystick calibration without needing a screen.
- Ergonomic Design: Comfortable grip for extended use.
- Versatile Switches: Features a mix of three-stage and two-stage switches for various flight modes and functions.
- Simulator Support: Compatible with multiple FPV simulators, enhanced by an optional wireless dongle.
- Bluetooth 4.2: Supports handle mode for additional connectivity options.
- External NANO TX Module Expansion: Allows for connection of third-party TX modules, automatically powering off the internal module when an external one is detected.
5. Setup
5.1 Battery Installation
The HGLRC C1 Remote Controller requires two 18650 flat head batteries (not included) for operation. Please ensure correct polarity when installing.
- Locate the battery compartment on the back of the controller.
- Open the battery compartment cover.
- Insert two 18650 flat head batteries, observing the polarity markings (+/-).
- Close the battery compartment cover securely.
5.2 Powering On/Off
To power on the controller, press and hold the power button located on the front face until the indicator lights illuminate. To power off, press and hold the power button again until the lights turn off.
5.3 Binding Procedure
To enter binding mode for frequency pairing:
- Ensure the receiver on your aircraft is in binding mode.
- Quickly power the HGLRC C1 Remote Controller on and off three times.
- The controller will enter binding mode, indicated by a specific LED pattern (refer to LED indicator section for details).
- Once bound, the LED indicator will show a solid light.
5.4 Connecting to a Simulator
The HGLRC C1 Remote Controller supports multiple simulators. You can connect it using the provided USB-C data cable or wirelessly with the optional dongle.
Wired Connection:
- Connect one end of the USB-C data cable to the controller's USB-C port.
- Connect the other end to your computer's USB port.
- The controller should be recognized as a joystick or game controller by your operating system.
- Launch your preferred simulator and configure the controller settings.
Wireless Connection (with Dongle):
If you have the wireless dongle, you can practice simulators without cables.
- Plug the wireless dongle into a USB-A or USB-C port on your computer.
- Ensure the dongle is powered on and recognized by your computer.
- The controller and dongle should automatically connect.
- Launch your preferred simulator and configure the controller settings.
5.5 External NANO TX Module Expansion
The HGLRC C1 Remote Controller allows for external NANO TX module expansion. When an external module is connected, the built-in TX module will automatically power off.
- Locate the NANO TX module bay on the controller.
- Carefully insert your compatible NANO TX module into the bay.
- Ensure the module is securely seated.
- The controller will automatically detect the external module and switch its transmission to it.
6. Operating Instructions
6.1 Basic Controls
The HGLRC C1 features two main joysticks (rockers) for primary control inputs. These are potentiometer sensors, providing precise control.
- Joystick Calibration: The controller supports joystick calibration without a screen. Refer to the LED indicator patterns for feedback during calibration.
- Power Adjustment: Adjust the power output of the TX module directly from the controller.
6.2 Switches
The controller is equipped with both three-stage and two-stage switches for various functions, such as arming/disarming, flight mode selection, or auxiliary controls.
- Three-stage Switch: Provides three distinct positions for complex functions.
- Two-stage Switch: Offers two positions for simpler on/off or mode toggling.
6.3 Bluetooth 4.2 Handle Mode
The HGLRC C1 supports Bluetooth 4.2 handle mode, allowing it to connect to compatible devices as a game controller.
7. Maintenance
7.1 Firmware Upgrade
Both the remote control and the optional wireless dongle support firmware upgrades.
- Remote Control: Firmware can be upgraded via WiFi or a TYPE-C wire brush (USB-C cable).
- Wireless Dongle: Firmware can be upgraded via WiFi or USB plug.
7.2 Battery Care
- Charge batteries using the provided USB-C cable. The charging current is 1.2A, and a full charge takes approximately 3-4 hours.
- Avoid overcharging or completely draining the batteries.
- If storing the controller for an extended period, remove the batteries.
7.3 Cleaning
Use a soft, dry cloth to clean the exterior of the controller. Do not use harsh chemicals or solvents.
8. Troubleshooting
- Controller not powering on: Ensure batteries are correctly installed and charged.
- Binding issues: Confirm the receiver is in binding mode and repeat the controller's binding procedure (power on/off three times quickly).
- No response in simulator: Check USB-C cable connection or ensure the wireless dongle is properly inserted and recognized. Verify controller settings within the simulator software.
- External TX module not working: Ensure the NANO TX module is fully seated in its bay. The internal TX module should automatically disable.
9. Specifications
9.1 Remote Control Parameters
| Feature | Specification |
|---|---|
| Built-in ELRS | ELRS 2.4GHz |
| Built-in ELRS refresh rate | 250Hz |
| Remote control sensor type | Potentiometer sensor |
| Antenna | Built-in ipex1 generation copper tube antenna |
| Working voltage | 6-8.4V DC |
| Remote control distance | Greater than 500m |
| Output interface | TX module NANO bin (CRSF protocol), 3.5MM analog trainer port (TYPE-C for charging and firmware flashing only) |
| Battery | 18650 flat head battery x2 (need to be installed by yourself) |
| Charging | TYPE-C charging current 1.2A, charging time 3-4 hours |
| Remote control channel | 8 channels |
| Bluetooth | Bluetooth 4.2 |
| ELRS firmware upgrade method | WiFi or TYPE-C wire brush |
| ELRS firmware version | ELRS 3.0 |
| ELRS firmware name | DIY devices 2.4 GHz DIY ESP32+ E28 2.4GHz TX |
| Weight | 195g (excluding battery) |
| Size | 160mm x 130mm x 50mm (excluding remote control) |
9.2 Dongle Parameters
| Feature | Specification |
|---|---|
| Built-in ELRS Maximum supported frequency | 250Hz |
| Receiving distance | More than 200m |
| Binding method | Quickly power on and off three times to enter binding mode |
| Interface | USB TYPE-C + USB TYPE-A double plug |
| Working voltage | 5V |
| ELRS firmware upgrade method | WiFi or USB plug |
| ELRS firmware version | ELRS 3.0 |
| ELRS Firmware Name | HGLRC 2.4 GHz HGLRC Hermes 2.4GHz RX |
| External receiver support protocol | Only supports CRSF protocol |
| Weight | 9.5g |
| Size | 74mm x 21mm x 12.5mm |
10. User Tips
Based on common user experiences and questions:
- For optimal performance, ensure your controller and receiver firmware are always up to date.
- When using the wireless dongle for simulators, ensure it is securely plugged into a compatible USB port.
- Practice regularly with a simulator to improve your piloting skills without risking damage to your physical drone.
- If experiencing range issues, check for potential interference in your operating environment and ensure antennas are unobstructed.
11. Warranty and Support
For warranty information, technical support, or service inquiries, please contact HGLRC customer support through their official website or the retailer where the product was purchased. Keep your proof of purchase for warranty claims.