Introduction
This manual provides important information for the safe and effective operation of your CNCEST 3000W Electric Wall Chaser Concrete Cutter, Model 350A. Please read all instructions carefully before use to ensure proper handling, prevent accidents, and maximize the lifespan of your tool. Keep this manual for future reference.

Figure 1: CNCEST 3000W Electric Wall Chaser Concrete Cutter
Important Safety Information
WARNING! READ ALL INSTRUCTIONS AND UNDERSTAND THEM BEFORE OPERATING THIS PRODUCT. FAILURE TO FOLLOW ALL INSTRUCTIONS LISTED BELOW MAY RESULT IN ELECTRIC SHOCK, FIRE AND/OR SERIOUS INJURY. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
When using power tools, basic safety precautions should always be observed. To reduce the risk of fire, electric shock, and personal injury, including the following. Read all these instructions before attempting to operate this product and save these instructions. The term "power tool" in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.
1. Work Area Safety
- Keep the work area clean and well lit. Cluttered or dark areas invite accidents.
- Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.
- Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.
2. Electrical Safety
- Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock.
- Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
- Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.
- Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock.
- When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.
- If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply. Use of an RCD reduces the risk of electric shock.
3. Personal Safety
- Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury.
- Use personal protective equipment. Always wear eye protection. Protective equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries.
- Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energizing power tools that have the switch on invites accidents.
- Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.
- Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.
- Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewelry or long hair can be caught in moving parts.
- If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust-related hazards.
4. Power Tool Use and Care
- Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed.
- Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.
- Disconnect the plug from the power source and/or the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.
- Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.
- Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool's operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.
- Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.
- Use the power tool, accessories and tool bits etc., in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation.
5. Service
- Have your power tool serviced by a qualified repair person. This power tool complies with applicable safety regulations. Repairs should only be performed by qualified persons using original spare parts, otherwise considerable hazards for the user may arise.
- When servicing a tool, use only identical replacement parts. Follow instructions in the Maintenance section of this manual. Use of unauthorized parts or failure to follow maintenance instructions may create a risk of electric shock or injury.
6. Safety Warnings for Cutting Machine Tools
- Grinding wheels must not be used.
- Diamond saw blades that do not comply with the manufacturer's specifications must not be used.
- Damaged, deformed or cracked cutting pieces must not be used.
- Do not operate the device without the fixed protective shield.
- Do not start the cutter when the cutting tool is in contact with the workpiece.
- After the cutting machine has been switched off, do not put it down before the cutting blade has come to a complete stop, and do not use external force to stop the diamond saw blade.
- Before changing the cutting blade, adjusting the cutting depth or water pipe, adjusting a part of the machine or repairing the cutting machine, the plug should be disconnected from the power supply and the diamond saw blade should be in a static state.
- If the diamond cutting disc is likely to cut through the dark wire or its own wire during operation, the power tool can only be held by the insulated gripping surface. The diamond cutting disc touching the live wire can energize the exposed metal parts of the power tool and expose the operator to the risk of electric shock.
- Be especially careful when making "blind cuts" in walls or other blind areas. Diamond saw blades can cut through gas or water pipes, wires, or objects bouncing off them.
- Keep your hands away from the cutting area and the diamond saw blade at all times. Your other hand should always hold the auxiliary handle. If you hold the cutter with both hands, you will not be injured by the saw blade.
- Do not touch the underside of the workpiece. The guard cannot protect the saw blade below the workpiece.
- Always use a diamond cutting disc of the correct size and arbor shape (diamond or circular). If the diamond saw blade does not match the clamping parts of the cutting machine, this will lead to eccentric operation and loss of control.
- Do not use damaged or undersized washers and screws. The use of damaged or non-conforming gaskets and screws can lead to uncontrolled operation.
Safety Symbols
| Symbol | Description |
|---|---|
| V | Volts |
| A | Amperes |
| Hz | Hertz |
| Min | Minutes |
| ~ | Alternating Current |
| No | No-load speed |
| Double insulated | |
| Read the manual | |
| Wear eye protection | |
| Wear hearing protection | |
| Wear dust mask | |
| Wear gloves | |
| Wear safety shoes |
Check the blade flanges for debris before installing a new blade. Do not use dull or damaged blades. Check blades regularly for condition and wear. Damaged or worn blades should be replaced immediately. Always ensure safe handling of excess material.
Product Overview
Familiarize yourself with the components of your electric wall chaser:

Figure 2: Product Components (Refer to exploded view for detailed numbering)
| Number | Name |
|---|---|
| 1 | Grinding Wheel Guard |
| 2 | Positioning Regulator |
| 3 | Suction Pipe |
| 4 | Auxiliary Handle |
| 5 | Safety Lock Button of Switch |
| 6 | Dust Flap |
| 7 | Saw Blade |
| 8 | Self-locking Button |
| 9 | Switch |
| 10 | Saw Blade Locking Nut |
| 11 | Water Inlet |
| 12 | Brush Cover |
Specifications
| Feature | Specification |
|---|---|
| Model | 350A |
| Power | 3000W |
| Voltage/Frequency | 220V~60Hz |
| No-Load Speed | 4200rpm |
| Maximum Torque | 7N.m |
| Blade Diameter | 350mm / 14in |
| Max. Flow Rate (Water Pump) | 4L/min / 140.8oz./min |
| Water Pump Rated Power | 30W |
| Leakage Protector Model | ABLB-16-1 |
| Leakage Protector Voltage | 250V |
| Product Size (D*H) | 70*35cm / 27.6*13.8in |
| Gross Weight | 15.5kg / 34lbs |
| Color | Yellow |
| Power Source | AC |
| Plug Type | EU Standard |
| Application | Cutting steel, aluminum alloys, wood, concrete, stones, glass, for fire prevention, disaster relief, demolition, construction engineering, bridge and road construction, house demolition, landscaping operations, power repair. |
Setup
Before Operation
- Power Source: Ensure that the power source to be used complies with the power requirements specified on the nameplate (220V~60Hz).
- Power Switch: Ensure the power switch is in the OFF position. If the plug is connected to an outlet while the power switch is in the ON position, the power tool will start immediately, which could cause a serious accident.
- Extension Cord: If the work area is far from the power source, use an extension cord with sufficient diameter and capacity. The extension cord should be kept as short as possible.
- Checking and Installing the Diamond Disc: Check that the diamond disc is the prescribed one and is not cracked, broken, or bent. Check that the diamond tool is securely installed.
- Wheel Guard Knob: Check that the knob used to secure the wheel guard is tight. Ensure that the knob securing the wheel guard is sufficiently tight. If this knob is loose, it can lead to operator injury.
Installing/Removing the Diamond Wheel
CAUTION! ALWAYS DISCONNECT THE CUT-OFF GRINDER FROM THE POWER SUPPLY BEFORE MAKING ADJUSTMENTS.
For your safety and protection, please do not attempt to cut tiles and other workpieces until the tools are fully assembled and installed. Before operation, please read the operating manual thoroughly to understand the machine's function and the potential dangers of incorrect operation.
- Turn off the tool switch and unplug it from the outlet.
- Press the self-locking button with one hand and use the provided wrench to loosen the screw (anti-tooth screw) clockwise.
- Remove the small elastic pressure plate and the outer flange (pressure plate).
- Place the saw blade on the step of the inner flange (pressure plate) and pay special attention that different types of saw blades may have a small inner washer to ensure reliable contact between the saw blade and the inner flange (pressure plate).
- Position the outer flange disc (pressure plate) on the drive shaft.
- Place a small elastic pressure plate.
- Press the self-locking button with one hand and with the other hand lock the bolt (anti-tooth bolt) with a wrench counter-clockwise.
- Carefully rotate the saw blade to check if the self-locking pin returns to its normal position and if the saw blade rotates normally.
NOTE:
Be careful! The direction of the arrow on the saw blade must match the direction of the machine cover. For your safety, the wrench should be removed immediately after use and stored in the toolbox.

Figure 3: Product and included accessories for installation
Adjusting the Shield Angle
- When cutting irregular workpieces, if the protective shield and workpiece interfere, the angle of the protective cover can be adjusted to best meet the cutting and protection requirements.
- Loosen the plastic knob, rotate the protective cover to a suitable position, and then lock the plastic knob.

Figure 4: Blade adjustment knob
Operating Instructions
Practical Application
- Power Supply: The power supply voltage must match the voltage specified on the power tool's nameplate.
- Workpiece Check: Check the workpiece before operation. Not only must the cutting blade be correctly installed, but it must also be able to rotate freely. No-load testing should not be performed for at least 30 seconds. Do not use damaged, deformed, or vibrating cutting pieces. Damaged cutting parts can break and cause injury.
- Dust Control: Dust from processing lead-containing pigments, minerals, and metals is harmful to health. Keep the air in the workplace clean. It is better to wear a mask with a P2 filter.
Switch Operation

Figure 5: Anti-Self-Locking Button and Switch
- To turn on: Press the anti-self-locking button and then the switch button.
- To turn off: Turn off the switch.
Cutting Precautions
- Always inspect the diamond tool before starting work.
- Never use a diamond disc that is cracked, broken, or bent.
- Ensure proper water supply when wet cutting.
- Only begin cutting when the diamond disc has reached its maximum speed.
- If the diamond disc jams or an unusual noise occurs, immediately switch off the power supply.
- Never use the diamond tool to cut zigzag or curved lines. Never use the side surface of the diamond disc. Never use it for angled cutting.
- If excessive force is applied to the diamond blade to align it with the marked line during cutting, this could not only overload the motor and cause fire damage, but also overheat the diamond blade and shorten its lifespan.
- Ensure that the power cord does not come into contact with the diamond disc during operation.
- When work is completed, switch off the power supply and disconnect the plug from the socket.
- Support the workpiece so that what will happen is predictable and the cut remains open during cutting.
- Check that the blade is not in contact with anything when starting the machine.
- Always cut at maximum speed.
- Start cutting gently so that the machine can work on the blade without pressure or force.
- Move the blade slowly back and forth to achieve a small contact area between the blade and the material to be cut. This lowers the blade temperature and ensures an effective cut.
- Guide the machine downwards in line with the blade. Side pressure can damage the blade and is very dangerous.

Figure 6: Cutting a line on the ground

Figure 7: Cutting a wall
Product Demonstration Video
Video 1: Product demonstration showing cutting operations.
Maintenance
General Maintenance
- Inspection of the Diamond Tool: A worn diamond tool overloads the motor and reduces working efficiency. Replace it with a new one.
- Checking Mounting Screws: Regularly check all mounting screws and ensure they are properly tightened. If any screws are loose, tighten them immediately. Failure to do so could lead to serious hazards.
- Motor Maintenance: Exercise due care to ensure that the winding is not damaged and/or wet with oil or water.
- Cleaning: Keep the tool clean and free from dirt. Avoid using cleaning agents containing benzene, trichloroethylene, chloride, or ammonia, as these can damage plastic parts.
- Malfunctions: In case of electrical or mechanical malfunctions, immediately switch off the tool and unplug it.
- Sparking: Excessive sparking may indicate the presence of dirt in the motor or worn carbon brushes. Check for wear and replace them when they reach 1/4" (6mm).
Carbon Brush Replacement
Attention! Please check the size of the carbon brush after a long period of operation. If it is less than 7 mm, it is necessary to replace the carbon brush in time. Timely replacement of the carbon brush prevents damage to the machine motor.
- Loosen the screws on the brush holder cover.
- Remove the brush holder cover.
- Open the coil spring.
- Remove the carbon brush holder with needle-nose pliers and take out the carbon brush.
- Install the original carbon brush and insert the buckle into the brush holder.
- Cover the brush holder cover and screw in the screws to fix the brush holder cover.
Environmental Protection
Scrapped power tools and accessories contain many valuable raw materials that can also be recycled to recover grinding chips or cutting dust. The dust contains harmful substances, so it should not be disposed of as ordinary waste, but in special waste recycling stations.
Troubleshooting
- Tool Jams or Unusual Noise: If the diamond disc jams or an unusual noise occurs during operation, immediately switch off the power supply and unplug the tool. Inspect the blade and workpiece for obstructions or damage.
- Excessive Sparking: If you observe excessive sparking from the motor, this may indicate dirt accumulation in the motor or worn carbon brushes. Refer to the 'Maintenance' section for instructions on cleaning and replacing carbon brushes.
- Motor Overload/Reduced Efficiency: If the motor feels overloaded or cutting efficiency decreases, check if the diamond tool is worn and replace it if necessary. Ensure you are not applying excessive force during cutting.
- Blade Overheating: If the diamond blade overheats, it may be due to excessive force or improper cutting technique. Ensure you are moving the blade slowly back and forth to maintain a small contact area and allow for cooling.
User Tips
- Cutting Depth: For cutting depths greater than 100mm, it is recommended to make 2 or 3 passes to prevent motor overload and extend blade life.
- Vertical Wall Cutting: When cutting walls vertically, ensure the head is facing down to prevent water from entering and damaging the motor. Operate the machine from top to bottom when grooving to save energy and protect the motor.
- Water Supply for Pump: Remember to prepare a bucket for the water pump when using the wet cutting feature. Avoid running the pump dry for extended periods to prevent damage to the pump core.
- Rest Periods: For continuous cutting, especially for long distances or hard materials, allow the machine to rest for 5-10 minutes or run at no-load after every 5-10 minutes of continuous operation.
- Pre-Shutdown No-Load Run: Before switching off the machine, let it run at no-load for a short period. This helps protect the motor and extends its lifespan.
Warranty and Support
For detailed warranty information, service, or technical support, please refer to the official product documentation or contact the retailer where you purchased the product. Always use original spare parts for repairs to ensure safety and maintain product performance.
A user manual in PDF format is available for download: User Manual (PDF)