SUMRY EP4200-H

Contents

SUMRY EP4200-H Solar Inverter Instruction Manual

All-in-one Solar Inverter Charger with Dual Voltage Output

1. Introduction and Overview

The SUMRY EP4200-H is an advanced all-in-one solar inverter charger designed for efficient power management in various applications. It integrates an MPPT charge controller, battery charger, and power inverter into a single unit, offering dual voltage output capabilities (2.3KW for 12VDC systems and 4.2KW for 24VDC systems).

This inverter features a 100A MPPT solar charge controller and a 100A battery charger, with a PV input range of 55-500VDC and a maximum PV array power of 4000W. The output is a stable 230VAC at 50/60Hz, making it compatible with a wide range of electrical appliances. It is battery adaptive, supporting 12V and 24V battery systems, including GEL, LI (Lithium), AGM, USER-defined, and FLD (Flooded) types.

SUMRY All-in-one Solar Inverter Charger with specifications
Figure 1: Overview of the SUMRY All-in-one Solar Inverter Charger, highlighting its MPPT charge controller, power inverter, and battery charger functions.

2. Safety Information

Please read and understand all safety instructions before installation and operation to prevent injury and damage to the unit. Keep this manual for future reference.

General Safety Precautions:

  • All wiring and installation procedures must be performed by qualified personnel in accordance with local electrical codes and regulations.
  • Ensure proper grounding of the inverter.
  • Do not disassemble the inverter. There are no user-serviceable parts inside.
  • Keep the inverter away from flammable materials, moisture, and direct sunlight.
  • Ensure adequate ventilation around the inverter to prevent overheating.

Integrated Safety Protections:

The SUMRY EP4200-H is equipped with comprehensive safety features to ensure reliable and stable operation:

  • Overload Protection: Prevents damage from excessive load.
  • Overheating Protection: Shuts down the unit if internal temperature exceeds safe limits.
  • Short Circuit Protection: Protects against short circuits in the output.
  • Overcurrent Protection: Safeguards against excessive current draw.
  • Battery Protection: Includes safeguards against overcharge and over-discharge.
  • High/Low Voltage Protection: Protects the system from abnormal voltage levels.
SUMRY Inverter All Round Safety Protection features
Figure 2: Visual representation of the inverter's safety protection features.

3. Product Features

The SUMRY EP4200-H offers a range of features for optimal solar power utilization:

  • Pure Sine Wave Output: Provides commercial-grade, high-quality AC power, compatible with over 98% of electrical appliances, ensuring efficient and stable operation.
  • Dual Voltage Compatibility: Works with both 12VDC and 24VDC battery systems. Rated power is 2300W when operating with a 12VDC battery and 4200W with a 24VDC battery.
  • Advanced MPPT Technology: Built-in MPPT charge controller with an operating voltage range of 55V to 500V and an open circuit voltage of 500VDC, maximizing solar energy harvest.
  • Real-Time Monitoring: Features a clear LCD display for effortless real-time monitoring of system status. An optional WiFi module allows for remote monitoring and control via the Sun house App.
  • Hybrid Functionality: Supports three charging modes (Solar First, Solar and Utility, Only Solar) and three output modes (SUB, SBU, MKS), making it suitable for various hybrid solar scenarios.
  • Battery Type Adaptability: Compatible with multiple battery types including GEL, Lithium (LI), AGM, USER-defined, and Flooded (FLD) batteries.
  • Communication Ports: Includes an RS485 port for communication with Battery Management Systems (BMS) and an RS232 communication port.
  • Dustproof Design: Features a built-in anti-dust kit and a dustproof construction for enhanced durability.
Pure Sine Wave Inverter comparison with Modified Sine Wave
Figure 3: Comparison illustrating the superior compatibility and stability of Pure Sine Wave output.
Inverter working with 12V and 24V battery systems and compatible battery types
Figure 4: The inverter's compatibility with 12V and 24V battery systems and various battery types.

4. Setup and Installation

Proper installation is crucial for the safe and efficient operation of your SUMRY solar inverter. Always ensure all connections are secure and follow local electrical codes.

4.1 Product Appearance and Connections

SUMRY Inverter Product Appearance: Front, Top, Back, Side Views
Figure 5: Various views of the inverter, showing its physical layout and connection points.
SUMRY Inverter System Diagram with labeled components
Figure 6: System Diagram with labeled components for easy identification.
  1. LCD screen
  2. Status indicator
  3. Charging indicator
  4. Fault indicator
  5. Function keys (ESC, UP, DOWN, ENTER)
  6. Power on/off switch
  7. AC input
  8. AC output
  9. PV input
  10. Battery input
  11. Circuit breaker
  12. Ground wire terminal
  13. BMS communication port
  14. RS232 communication port

4.2 PV Connection

CAUTION: Before connecting the PV module, please install a separate DC circuit breaker between the inverter and the PV module.

WARNING! All wiring must be performed by qualified personnel.

WARNING! It is very important for system safety and efficient operation to use appropriate cable for PV module connection. To reduce risk of injury, please use the proper recommended cable size.

PV Module Selection:

When selecting proper PV modules, consider the following parameters:

  1. Open circuit Voltage (Voc) of PV modules should not exceed the maximum PV array open circuit voltage of the inverter (500VDC).
  2. Open circuit Voltage (Voc) of PV modules should be higher than the minimum battery voltage.
Recommended PV Connection Cable Size
ModelWire GaugeTorque Value
12V/24V1 * 16 AWG1.2-1.6 Nm
PV Array Power and Current Specifications
ParameterValue
Max. PV Array Power4000W
I Max. PV18A
Nominal PV Voltage240V
PV Array MPPT Voltage Range55-500V
Max. PV Array Open Circuit Voltage500V

Example configuration for 250Wp PV module:

250Wp PV Module Configuration Example
Solar panel parameters -250WpRange (Min in serial: 6 pcs, max in serial: 11 pcs)Q'ty of panelsTotal Input
-Vmp: 30.1Vdc3 pcs in serial3750W
-Imp: 8.3A6 pcs in serial61500W
-Voc: 37.7Vdc8 pcs in serial82000W
-Isc: 8.4A12 pcs in serial123000W
-Cells: 6013 pcs in serial133250W
8 pcs in serial and 2 sets in paralleled164000W

4.3 System Wiring Diagram

SUMRY Inverter Link Instructions Wiring Diagram
Figure 7: Wiring diagram showing connections between solar panels, generator, utility grid, inverter, battery, and household loads.

4.4 Communication and Setting of Lithium Battery (BMS)

To enable communication with a Lithium Battery Management System (BMS), connect an RJ45 communication cable between the inverter and the battery. Ensure that the lithium battery BMS port's PIN configuration corresponds with the inverter BMS communication port.

Inverter BMS Port PIN Definition
Pin numberPort definitions
1RS485B
2RS485A
3NG
4NG
5NG
6NG
7RS485A
8RS485B
RJ45 Pinout for BMS Communication
Figure 8: Diagram illustrating the RJ45 pinout for BMS communication.

5. Operating Instructions

The SUMRY EP4200-H offers flexible operating modes to suit various energy needs.

5.1 Charging Modes

The inverter supports three distinct charging modes:

  1. Solar First: Prioritizes solar power for charging batteries and supplying loads.
  2. Solar and Utility: Uses solar power as the primary source, supplementing with utility grid power when solar is insufficient.
  3. Only Solar: Charges batteries and powers loads exclusively from solar energy.

5.2 Output Modes

The inverter provides three output modes:

  1. SUB (Solar-Utility-Battery): Solar power is the primary source, followed by utility grid, then battery.
  2. SBU (Solar-Battery-Utility): Solar power is the primary source, followed by battery, then utility grid.
  3. MKS (Utility-Solar-Battery): Utility grid is the primary source, followed by solar, then battery.
SUMRY Inverter Input Charging Modes and Output Modes
Figure 9: Diagram illustrating the three charging modes and three output modes.

5.3 Monitoring and Control

  • LCD Display: The integrated LCD screen provides real-time information on input, output, battery status, and load.
  • Optional WiFi Module: For enhanced monitoring, an optional WiFi module can be connected to the inverter. This allows you to monitor and control the system remotely via the "Sun house App" on your smartphone or tablet.
SUMRY Inverter Real-Time Monitoring with LCD and Optional WiFi Module
Figure 10: Real-time monitoring capabilities with the LCD display and optional WiFi module for app integration.

5.4 Settings

  • Charging Current: The charging current can be set through the LCD interface according to battery requirements.
  • Utility Grid Input Voltage Range: The input voltage range of the utility grid can be selected based on the requirements of the connected loads (e.g., household appliances, personal computers).

6. Maintenance

The SUMRY EP4200-H is designed for low maintenance. Regular checks can help ensure optimal performance and longevity.

  • Cleaning: Periodically clean the exterior of the inverter to prevent dust buildup. The unit features a dustproof design and a built-in anti-dust kit, but external cleaning is still recommended.
  • Ventilation: Ensure that the ventilation openings are clear and not obstructed to allow for proper airflow and heat dissipation.
  • Connections: Periodically check all electrical connections (PV, battery, AC input/output) for tightness and signs of corrosion.
  • Environmental Conditions: Ensure the inverter is operating within its specified environmental conditions (temperature, humidity).

7. Troubleshooting

The inverter is designed with self-protection features. If the inverter enters a fault state, the fault indicator (4 in Figure 6) will illuminate, and an error code may be displayed on the LCD screen. Refer to the specific error codes in the full product manual for detailed troubleshooting steps.

Common issues and their general causes:

  • Overload: Reduce the connected load.
  • Overheating: Ensure adequate ventilation and clear any obstructions around the cooling fins.
  • Short Circuit: Check output wiring for short circuits.
  • Overcurrent: Inspect connected devices for faults causing excessive current draw.
  • Battery Issues (High/Low Voltage): Check battery connections, voltage, and health. Ensure battery settings in the inverter match the connected battery type.

If the issue persists after basic troubleshooting, contact customer support.

8. Specifications

The SUMRY EP4200-H inverter comes in two main power configurations depending on the battery voltage.

SUMRY EP4200-H 2300W (12VDC System) Specifications
ParameterValue
ModelEP-4200H 2300W
Max. PV Array Power4000W
Battery Voltage12VDC
MPPT Voltage Range55-500VDC
Output Voltage230VAC ±5%
Max. Charge Current100A
Frequency Range50/60Hz
Surge Power4600W
SUMRY EP4200-H 4200W (24VDC System) Specifications
ParameterValue
ModelEP-4200H 4200W
Max. PV Array Power4000W
Battery Voltage24VDC
MPPT Voltage Range55-500VDC
Output Voltage230VAC ±5%
Max. Charge Current100A
Frequency Range50/60Hz
Surge Power8400W
General Specifications
ParameterValue
Size40*35*19cm
Weight6.7kg
Output TypeSINGLE
OriginMainland China
CertificationCE
Is Smart DeviceYes (with optional WiFi module)
Detailed specifications table for SUMRY EP4200-H 2300W and 4200W models
Figure 11: Comprehensive specifications for both 12VDC (2300W) and 24VDC (4200W) models.

9. User Tips

  • Remote Monitoring: Consider purchasing the optional WiFi module to enable remote monitoring and control of your inverter via the Sun house App. This allows you to check system status and adjust settings from anywhere.
  • Battery Compatibility: When selecting batteries, ensure they are compatible with the inverter's 12V or 24V system and match one of the supported types (GEL, LI, AGM, USER, FLD) for optimal performance and charging.
  • Professional Installation: For safety and optimal performance, always have the inverter installed by a qualified electrician or solar professional.

10. Warranty and Support

For specific warranty details, including coverage period and terms, please refer to the documentation provided at the time of purchase or contact the SUMRY Official Store directly. Warranty information can vary by region and seller.

For technical support, troubleshooting assistance, or any inquiries regarding your SUMRY EP4200-H solar inverter, please contact the SUMRY Official Store or your authorized dealer. Provide your product model number (EP4200-H) and any relevant purchase details when seeking support.

© 2023 SUMRY. All rights reserved.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.