EPMAN EP-GA50

Contents

EPMAN 2" 52mm Digital Analog LED Racing Gauge Instruction Manual

Model: EP-GA50 Series

Brand: EPMAN

1. Introduction

This manual provides instructions for the EPMAN 2" (52mm) Digital Color Analog LED Racing Gauge series, including Boost, Oil Pressure, Water Temperature, Oil Temperature, Exhaust Gas Temperature (EGT), Tachometer, Air Fuel Ratio, and Volt gauges. These gauges are designed to provide accurate and real-time monitoring of various engine parameters for gasoline vehicles. Each gauge features a smoked tint lens when off and a vibrant color LED display when on, combining both digital and analog LED readouts for clear visibility.

EPMAN 2 inch 52mm Digital Analog LED Boost Gauge showing a reading of 98
EPMAN 2" 52mm Digital Analog LED Boost Gauge (Example)
Collection of EPMAN 2 inch 52mm Digital Analog LED gauges for various parameters like Air/Fuel Ratio, Boost, RPM, Oil Temp, EGT, Water Temp, Oil Press, and Volts
Various EPMAN 2" 52mm Digital Analog LED Gauges

2. Key Features

  • Universal Fitment: Designed to fit most gasoline vehicles and standard 2" (52mm) diameter gauge pods.
  • Dual Display: Features both digital and analog LED readouts for comprehensive data presentation.
  • Dynamic Color Display: Smoked tint lens when off, transforming into a vibrant color LED display when powered on.
  • Startup Scanning: Performs a self-check scan (green-yellow-red) upon startup.
  • Adjustable Units: Unit types (e.g., BAR/PSI, °C/F) can be changed via a dial switch for certain models.
  • Multiple Gauge Types: Available for Boost, Oil Pressure, Water Temperature, Oil Temperature, EGT, Tachometer, Air Fuel Ratio, and Volts.

3. Package Contents

Each EPMAN EP-GA50 series gauge package typically includes the following components:

  • 1 x Digital Analog LED Gauge (specific type: Boost, Oil Pressure, etc.)
  • 1 x Sensor (if applicable to the gauge type, e.g., Boost Sensor, Oil Temp Sensor, Water Temp Sensor, EGT Sensor, Oil Press Sensor)
  • 1 x 52mm Gauge Bracket
  • 1 x Instructions In English (generic)
  • Necessary wiring and small accessories (e.g., screws, double-sided tape, vacuum hose for boost gauge)
EPMAN gauge packaging box with 'OIL PRESS' label
Typical EPMAN Gauge Packaging
Components of an EPMAN gauge including the gauge unit, wiring, mounting bracket, and small accessories
Gauge components and accessories

4. Specifications

Attribute Value
Brand Name EPMAN
Model Number EP-GA50
Type 52mm Digital Gauge (Digital Color Analog LED)
Size 2 inches (52mm)
LED Color Blue (Digital Display), Multi-color (Analog LED)
Material PVC
Item Weight 0.5 kg
Placement on Vehicle FRONT
Special Features Universal, Smoke face
Compatibility Fit all 1-10 Cylinder Spark Ignition Motors
Country/Region of Manufacture CHINA

4.1. Gauge-Specific Specifications

Gauge Type Unit Type Display Range Digital Accuracy Sensor Thread Size
Tachometer (EP-GA50RPM) RPM 0-100*100RPM N/A N/A
Exhaust Gas Temp (EP-GA50EXTT) °C/F 20~120(*10°C)/39~219 (*10 F) Every 10°C/10F 1/8" NPT
Turbo Boost (EP-GA50BOOST) BAR/PSI -1.0~3.0BAR/-15~45PSI Every 0.1BAR/1PSI N/A
Air Fuel Ratio (EP-GA50AIFR) AFR 20~10 AFR Every 1AFR N/A
Oil Temperature (EP-GA50OILT) °C/F 50~150 °C /100~300F Every 1 °C /1F 1/8" NPT
Oil Pressure (EP-GA50OILP) PSI/Bar 0~145PSI/0~10BAR Every 1 PSI /0.5BAR 1/8" NPT
Water Temperature (EP-GA50WAT) °C/F 50~150 °C /100~300F Every 1 °C /1F 1/8" NPT
Volt (EP-GA50VOLT) V 8.0~18.0V Every 1V N/A

5. Setup and Installation

IMPORTANT: Installation tools and a detailed instruction manual are not included with the product. Professional installation is strongly recommended to ensure correct and safe operation.

Image showing the EPMAN gauge and its included gauge pod, emphasizing that installation tools are not included and professional installation is recommended.
Gauge with included pod. Professional installation is recommended.

While professional installation is advised, the following general steps outline the typical installation process for these gauges:

5.1. Mounting the Gauge

  1. Select a suitable location on your vehicle's dashboard or A-pillar for the gauge pod. Ensure it does not obstruct your view or interfere with vehicle controls.
  2. Drill a 2" (52mm) diameter hole at the chosen location for the gauge to sit flush.
  3. Insert the gauge into the mounting bracket/pod.
  4. Secure the gauge and bracket using the provided screws or double-sided tape, ensuring it is firmly in place.

5.2. Wiring Connections

The gauge requires power connections and, for most types, a sensor connection. The wiring colors may vary, but typically follow this scheme:

  • Red Wire: Connect to a +12V ignition switched power source (power only when the ignition is on).
  • Yellow Wire: Connect to a constant +12V battery power source (always on). This is often for memory functions or continuous illumination.
  • Black Wire: Connect to a reliable vehicle ground point.
  • Sensor Wire(s): Connect the sensor wire(s) from the gauge to the corresponding sensor (e.g., boost sensor, oil pressure sensor, temperature sensor). Refer to the specific sensor's instructions for correct wiring.

Ensure all connections are secure and properly insulated to prevent short circuits or electrical issues.

5.3. Sensor Installation (If Applicable)

For gauges requiring a sensor (e.g., Boost, Oil Pressure, Water/Oil Temp, EGT), the sensor must be installed in the appropriate location on your engine or exhaust system. Sensor thread size is typically 1/8" NPT. Consult a professional or vehicle-specific guides for optimal sensor placement.

6. Operation

6.1. Power On / Self-Check

Upon turning your vehicle's ignition on, the gauge will perform a self-check sequence, typically indicated by a green-yellow-red scanning light. After the self-check, the gauge will display the current reading for its respective parameter.

6.2. Reading the Display

The gauge provides both a digital numerical readout and an analog LED bar display. The digital display offers precise values, while the analog LED bar provides a quick visual reference of the parameter's level, often with color changes indicating different ranges (e.g., green for normal, yellow for caution, red for warning).

6.3. Changing Backlight Color

Most EPMAN EP-GA50 series gauges feature a button (usually located on the front or side) that allows you to cycle through different backlight colors. Press the button briefly to change the color.

6.4. Changing Unit Type (If Applicable)

For certain gauges (e.g., Boost, EGT, Oil Temp, Oil Press, Water Temp), the unit type (e.g., BAR/PSI, °C/F) can be changed. This is typically done via a 'Dial Switch' or by holding down the button for an extended period (e.g., 3 seconds) to enter a setting mode. Refer to the generic instructions included with your specific gauge for detailed steps on unit conversion.

7. Maintenance

  • Cleaning: Use a soft, dry cloth to clean the gauge face and body. Avoid abrasive cleaners or solvents that could damage the lens or finish.
  • Wiring Inspection: Periodically check all wiring connections for tightness and signs of wear or corrosion.
  • Sensor Check: For gauges with external sensors, inspect the sensor and its connections for any damage or blockages.
  • Environmental Protection: While designed for automotive use, avoid exposing the gauge to extreme moisture or direct water spray.

8. Troubleshooting

Problem Possible Cause Solution
Gauge does not power on Incorrect wiring, blown fuse, no power to ignition/battery wire. Check all power and ground connections. Inspect vehicle fuses. Ensure ignition is on for red wire.
Incorrect or no reading Sensor not connected, faulty sensor, incorrect sensor type, wiring issue. Verify sensor is correctly installed and connected. Check sensor wiring for damage. Replace sensor if faulty.
Gauge flickers or unstable display Unstable power supply, loose ground connection. Ensure power connections are stable. Check ground wire for a solid connection to the chassis.
EGT Gauge shows '20' and doesn't change Real temperature has not reached 200°C. This is normal behavior. The gauge will only show accurate readings above 200°C (or 20 units on the display).

9. User Tips

No specific user tips were available from customer reviews or Q&A for this product at this time. However, general best practices for automotive gauges include:

  • Always ensure your vehicle's battery is disconnected before performing any electrical work.
  • Use appropriate wire gauges and connectors for all electrical installations.
  • Route wiring carefully to avoid pinching, chafing, or exposure to excessive heat.
  • Consider using a dedicated fuse for your gauge installation to protect your vehicle's electrical system.

10. Warranty and Support

This product comes with a 3-month warranty. In case of any issues requiring repair under warranty, the gauge will need to be returned to the manufacturer in China.

For technical support, troubleshooting assistance, or warranty claims, please contact the seller or the EPMAN customer service directly. Provide your purchase details and a clear description of the issue to facilitate a quicker resolution.

For additional documentation, a generic user manual PDF is available for reference: View User Manual (PDF)

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.