1. Introduction
Thank you for choosing the ANDELI RSR Series Portable Capacitor Discharge Stud Welding Machine. This manual provides essential information for the safe operation, setup, maintenance, and troubleshooting of your RSR-1600, RSR-2500, or RSR-3500 model. Please read this manual thoroughly before using the machine to ensure proper function and to prevent injury or damage.

Figure 1: ANDELI RSR-2500 Portable Capacitor Discharge Stud Welding Machine
2. Safety Instructions
Always adhere to the following safety guidelines to prevent accidents and ensure safe operation:
- Personal Protective Equipment (PPE): Always wear appropriate PPE, including a welding helmet with suitable shade, welding gloves, flame-resistant clothing, and safety shoes.
- Ventilation: Ensure adequate ventilation in the work area to disperse welding fumes.
- Flammable Materials: Do not weld near flammable materials, liquids, or gases.
- Electrical Safety: Ensure the machine is properly grounded. Never touch live electrical parts. Disconnect the power supply before performing any maintenance, changing accessories, or when the machine is not in use.
- Charging Safety: Do not attempt to weld while the machine is in its charging cycle. Wait for the 'READY' indicator to illuminate.
- Work Area: Keep the work area clean and free from clutter. Ensure stable footing.
3. Package Contents
Upon unpacking, verify that all the following items are included:

Figure 2: Included accessories with the ANDELI RSR Stud Welding Machine
- ANDELI RSR Series Stud Welding Machine (RSR-1600, RSR-2500, or RSR-3500 model)
- Ground Clamp (x2)
- Stud Welding Torch
- Chucks (M3, M4, M5, M6, M8, M10 - specific sizes may vary by model)
- Carbon Steel Screws (M6*10)
- User Manual
4. Product Overview
The ANDELI RSR series features a robust design with intelligent controls for efficient stud welding.
4.1 Control Panel

Figure 3: Control Panel with indicators and digital display
- POWER Indicator: Illuminates when the machine is powered on.
- CHARGE Indicator: Illuminates during the capacitor charging cycle.
- READY Indicator: Illuminates when the capacitors are fully charged and the machine is ready to weld.
- WELD Indicator: Illuminates during the welding process.
- Digital Display: Shows the current welding voltage.
- Voltage Adjustment Knob: Used to precisely adjust the welding voltage (M3-M10 settings).
4.2 Key Features

Figure 4: Key features including cooling and protection
- High-speed cooling fans for efficient heat dissipation.
- Overtemperature protection to prevent damage from prolonged use.
- DC Inverter technology for stable and efficient power delivery.
- Advanced thyristor devices for reliable performance.
- Large capacity capacitors (e.g., 3x 36000uF for RSR-2500) for rapid discharge.
5. Setup
- Unpack: Carefully remove the welding machine and all accessories from its packaging. Inspect for any shipping damage.
- Connect Ground Clamp: Attach the two ground clamps securely to the workpiece. Ensure good electrical contact.
- Connect Welding Torch: Connect the stud welding torch to the designated port on the front panel of the machine.
- Install Chuck: Select the appropriate chuck size for the stud diameter you intend to weld (e.g., M3, M4, M5, M6, M8, M10). Insert it into the welding torch and secure it.
- Power Connection: Connect the machine's power cord to a suitable 220V power outlet.
6. Operating Instructions
- Power On: Turn on the main power switch on the machine. The 'POWER' indicator will light up.
- Charging Cycle: The 'CHARGE' indicator will illuminate as the capacitors charge. This process is very fast, typically around 4 seconds. Wait for the 'READY' indicator to light up, signaling the machine is prepared for welding.
- Adjust Welding Voltage: Use the voltage adjustment knob on the control panel to set the desired welding voltage. Refer to the 'Charging Voltage Reference' table in the Specifications section for recommended settings based on stud diameter.
- Load Stud: Insert the stud into the chuck of the welding torch.
- Position and Weld: Firmly press the stud against the workpiece at the desired welding location. Press the trigger on the welding torch to initiate the weld. Hold steady until the weld is complete.
- Dual-Gun Control (if applicable): For models supporting dual-gun control, you can operate two welding torches simultaneously or alternately, allowing for continuous work without waiting for capacitor recharge between welds.
Video 1: Demonstration of the ANDELI RSR Stud Welding Machine in action, showing various stud and nail welding applications.

Figure 5: Welding results demonstrating speed and strength.

Figure 6: Wide range of workpieces compatible with the RSR series.
7. Maintenance
Regular maintenance ensures the longevity and optimal performance of your welding machine.
- Cleaning: Keep the machine clean. Regularly wipe down the exterior with a dry cloth. Ensure ventilation openings are free from dust and debris to prevent overheating.
- Torch and Chuck Inspection: Periodically inspect the welding torch and chucks for signs of wear, damage, or carbon buildup. Replace worn chucks to maintain weld quality.
- Cable Inspection: Check all welding cables and power cords for cuts, abrasions, or loose connections. Damaged cables can be a safety hazard and affect performance.
- Storage: Store the machine in a dry, clean, and well-ventilated area, away from direct sunlight, moisture, and extreme temperatures.
8. Troubleshooting
If you encounter issues with your welding machine, refer to the following common troubleshooting steps:
- Machine Does Not Power On:
- Check if the power cable is securely plugged into both the machine and the power outlet.
- Ensure the power outlet is functional.
- Verify the machine's main power switch is in the 'ON' position.
- No Weld or Weak Weld:
- Ensure the ground clamps are securely attached to the workpiece and have good electrical contact.
- Check that the stud is making firm contact with the workpiece.
- Verify that the correct welding voltage is set for the stud diameter and material (refer to the Specifications section).
- Inspect the chuck for wear or damage; replace if necessary.
- Machine Overheats (Overtemperature Protection):
- Allow the machine to cool down. The overtemperature protection will automatically reset once the temperature drops.
- Ensure that the machine's ventilation openings are not blocked.
- Reduce the duty cycle if welding continuously for extended periods.
9. Specifications

Figure 7: Detailed technical specifications and charging voltage reference.
9.1 Technical Parameters
| Property | RSR-1600 | RSR-2500 | RSR-3500 |
|---|---|---|---|
| Rated voltage(V) | 220±15% | 220±15% | 220±15% |
| Rated Power (VA) | 375 | 375 | 375 |
| Frequency (Hz) | 50/60 | 50/60 | 50/60 |
| Charge and discharge voltage(V) | 56-197 | 56-197 | 56-197 |
| Welding range | M3-M6 | M3-M8 | M3-M10 |
| Welding Material | Iron, carbon steel, stainless steel, aluminum, galvanized sheet | ||
| Welding energy | 1600JW/S | 2500JW/S | 5500JW/S |
| Power supply | Electrolytic capacitor | Electrolytic capacitor | Electrolytic capacitor |
| Capacitance | 72000μF | 108000μF | 141000μF |
| Level of protection | IP22 | IP22 | IP22 |
| Size(mm) | 490×320×210 | 490×320×210 | 490×320×210 |
| WEIGHT(KG) | <15.6KG | <17.3KG | <18.6KG |
9.2 Charging Voltage Reference
| STUD DIAMETER | CHARGING VOLTAGE(V) | REMARK |
|---|---|---|
| M3 | 55-65 | Adjust the parameters according to the actual situation |
| M4 | 65-75 | |
| M5 | 70-85 | |
| M6 | 85-110 | |
| M8 | 130-160 | |
| M10 | 160-180 |
10. User Tips
Maximize your welding experience with these practical tips:
- Surface Preparation: Always ensure the workpiece surface is clean, dry, and free from rust, paint, oil, or other contaminants for optimal weld quality.
- Test Welds: Before working on your final project, perform test welds on scrap material of the same type and thickness. This allows you to fine-tune the voltage settings for the best results.
- Fast Operation: Take advantage of the machine's rapid 4-second charging time to maintain a high work efficiency.
- Weld Quality: The RSR series is designed to produce strong, uniform welds with minimal heat distortion and low substrate damage. Ensure proper technique to achieve these results.
- Parameter Adjustment: Remember to adjust welding parameters (especially voltage) according to the specific stud diameter and material you are using.
11. Warranty and Support
For technical assistance, troubleshooting beyond this manual, or any warranty-related inquiries, please contact our customer service team directly.
Contact Information:
- WhatsApp: +86 18774005168
- Email: 18774005168@163.com

Figure 8: Contact details for support.