Hobbywing Spray System

Contents

Hobbywing Agricultural Drone Spray System Instruction Manual

1. Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of your Hobbywing Agricultural Drone Spray System. This system is designed for efficient and precise liquid application using agricultural drones, featuring a high-performance brushless water pump with an integrated Electronic Speed Controller (ESC) and pressure nozzles.

2. Product Overview

The Hobbywing Spray System is a comprehensive kit for drone-based spraying. It includes a brushless water pump, spray nozzles, carbon fiber spray arms, and all necessary tubing and connectors.

2.1 Components

  • Hobbywing Brushless Water Pump (5L/min or 8L/min variant)
  • Pressure Nozzles
  • Carbon Fiber Spray Arms
  • Water Tubing
  • Quick-Connect Fittings and T-connectors
  • Mounting Hardware (if applicable)
Complete Hobbywing Agricultural Drone Spray System Kit

Figure 1: Complete Hobbywing Agricultural Drone Spray System Kit (5L pump variant shown)

Hobbywing 5L Brushless Water Pump with integrated ESC and wiring

Figure 2: Hobbywing 5L Brushless Water Pump with integrated ESC and wiring

Spray arms with pressure nozzles and quick-connect fittings

Figure 3: Spray arms with pressure nozzles and quick-connect fittings

3. Specifications

The spray system is available with either a 5L/min or 8L/min brushless water pump. Refer to the table below for detailed specifications.

FeatureHobbywing 5L PumpHobbywing 8L Pump
Operating Voltage12-14S (DC44-60.9V)12-14S (DC44-60.9V)
Working Current<2A<2A
Weight388g (approx. 338g without wire)685g
Water Inlet Diameter10.5mm10.5mm
Water Outlet Diameter6.5mm6.5mm
Rated Power60W60W
Opening Flow5L/min8L/min
Dimensions (L*W*H)123*76*52mm140*95*70mm
Working Pressure0.35Mpa0.5Mpa
Protection LevelIP67IP67
Fixed PWM Throttle Stroke110-1940US110-1940US
Detailed specifications for Hobbywing 8L brushless water pump

Figure 4: Detailed specifications for Hobbywing 8L brushless water pump

4. Setup

Careful assembly and connection are crucial for optimal performance and safety. Ensure your drone is powered off and disconnected from any power source before beginning installation.

4.1 Mounting the Pump

  1. Choose a secure location on your agricultural drone for the water pump, ensuring it is balanced and does not interfere with other drone components.
  2. Use appropriate mounting hardware to firmly attach the pump to the drone frame.

4.2 Connecting Spray Arms and Nozzles

  1. Attach the carbon fiber spray arms to the drone's landing gear or designated mounting points.
  2. Securely connect the pressure nozzles to the spray arms.

4.3 Tubing Installation

  1. Connect the water inlet of the pump to your drone's liquid tank using appropriate tubing. Ensure a tight, leak-free connection.
  2. Connect the water outlet of the pump to the T-connectors and then to the spray nozzles using the provided tubing and quick-connect fittings.
  3. Route all tubing carefully, avoiding sharp bends or kinks that could restrict flow. Secure tubing with zip ties or clamps to prevent movement during flight.

4.4 Electrical Connections

  1. Connect the power input wires of the brushless water pump to a suitable power source on your drone (12-14S DC44-60.9V). Ensure correct polarity.
  2. Connect the PWM signal wire from the pump's integrated ESC to the drone's flight controller or a dedicated PWM output channel. The fixed PWM throttle stroke is 110-1940US.
  3. Verify all electrical connections are secure and insulated to prevent short circuits.

5. Operating Instructions

Before operating the spray system, perform a thorough pre-flight check of all connections and components.

5.1 Pre-Operation Check

  • Ensure the liquid tank is filled with the desired liquid.
  • Check all tubing for leaks or blockages.
  • Verify electrical connections are secure.
  • Confirm the PWM signal is correctly configured on your flight controller.

5.2 Powering On and Control

  1. Power on your agricultural drone.
  2. The water pump is controlled via a PWM signal from your flight controller. Adjust the PWM signal within the 110-1940US range to control the pump's speed and thus the spray output.
  3. Start with a low PWM value and gradually increase to achieve the desired spray pattern and flow rate.

5.3 Post-Operation

  1. After each use, ensure the pump is turned off via the PWM signal.
  2. Power down the drone.
  3. If spraying chemicals, flush the system with clean water to prevent residue buildup.

6. Maintenance

Regular maintenance will extend the lifespan and ensure reliable performance of your spray system.

6.1 Cleaning

  • Nozzles: Periodically inspect nozzles for clogging. Clean them with water or a mild cleaning solution if necessary. Replace damaged or worn nozzles.
  • Tubing: Flush the entire tubing system with clean water after each use, especially when using chemicals, to prevent blockages and corrosion.
  • Pump: The pump has an IP67 protection level, making it resistant to dust and water immersion. However, avoid prolonged submersion and clean the exterior with a damp cloth.

6.2 Inspection

  • Regularly check all connections (electrical and tubing) for tightness and signs of wear.
  • Inspect spray arms for any damage or cracks.
  • Ensure the pump is securely mounted.

7. Troubleshooting

If you encounter issues with your spray system, refer to the following common problems and solutions.

7.1 No Spray or Weak Spray

  • Check Liquid Level: Ensure the liquid tank is not empty.
  • Clogged Nozzles: Inspect and clean or replace any clogged nozzles.
  • Tubing Blockage/Kink: Check all tubing for kinks, blockages, or air bubbles.
  • Pump Power: Verify the pump is receiving adequate power (12-14S voltage).
  • PWM Signal: Ensure the PWM signal from the flight controller is active and within the correct range (110-1940US).

7.2 Leaks in the System

  • Loose Connections: Tighten all quick-connect fittings and tubing clamps.
  • Damaged Tubing: Inspect tubing for cracks or punctures and replace if necessary.
  • Nozzle Seals: Check the seals around the nozzles and replace if worn.

7.3 Pump Not Responding

  • Power Supply: Confirm the drone's battery is charged and connected correctly to the pump.
  • Electrical Connections: Recheck all wiring for loose connections or incorrect polarity.
  • PWM Signal: Verify the flight controller is sending a valid PWM signal. Test with a known working signal source if possible.

8. User Tips

  • Pre-Mix Chemicals: Always pre-mix chemicals thoroughly in a separate container before filling the drone's tank to ensure even distribution and prevent pump damage.
  • Filter Usage: Consider adding an inline filter before the pump inlet to prevent debris from entering and clogging the pump or nozzles.
  • Test Spray Pattern: Before full operation, perform a test spray with plain water to verify the nozzle pattern and flow rate are as desired.
  • Regular Calibration: Periodically calibrate your spray system's flow rate with your drone's flight speed to ensure accurate application rates.

9. Warranty & Support

This Hobbywing Spray System is manufactured to high-quality standards. For any technical assistance, troubleshooting beyond this manual, or warranty inquiries, please contact your original point of purchase or the official Hobbywing support channels. Please have your product model and purchase details ready when contacting support.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.