ORIVISION ZY-EH1304

Contents

ORIVISION 4-Channels 4K HDMI to IP Streaming Encoder

Model: ZY-EH1304

1. Introduction

The ORIVISION ZY-EH1304 is a professional hardware video and audio encoder designed for high-quality video transmission. It supports simultaneous encoding of up to two 4K@30Hz channels and two 1080P@60 channels of HDMI video. The encoder utilizes H.265 and H.264 encoding standards and supports a wide range of streaming protocols including HTTP, RTMP, RTMPS, HLS, UDP, and RTSP.

Its integrated and cost-effective design makes it suitable for various applications such as CATV digital head-ends, hotel IPTV systems, live streaming broadcasts, and media servers. This encoder is compatible with popular online live broadcast platforms like YouTube, Ustream, Twitter, WOWZA, and Facebook Live.

2. Safety Information

  • Ensure the device is placed in a well-ventilated area to prevent overheating.
  • Use only the provided power adapter to avoid damage.
  • Keep the device away from water, moisture, and extreme temperatures.
  • Do not attempt to open or repair the device yourself. Refer to qualified personnel for service.
  • Disconnect power before cleaning or moving the device.

3. Package Contents

Please check the box for the following items:

  • ORIVISION ZY-EH1304 Video Encoder x 1
  • Power Adapter x 1
  • Operation Manual x 1
ORIVISION ZY-EH1304 package contents including encoder, power adapter, and manual.
Figure 3.1: Package Contents

4. Device Overview

The ORIVISION ZY-EH1304 encoder features multiple input and output ports for versatile connectivity.

Labeled diagram of the ORIVISION ZY-EH1304 encoder's front and rear panels, showing Audio In ports (1-4), HDMI In ports (1-4), PWR LED, RST button, LAN port, and 12V/DC power input.
Figure 4.1: Device Interfaces

4.1. Front Panel

  • AUDIO IN (1-4): Four 3.5mm audio input jacks for external audio sources.
  • HDMI IN (1-4): Four HDMI input ports for video sources.
  • PWR: Power indicator LED.
  • RST: Reset button (recessed).
  • LAN: Ethernet port (RJ45) for network connection.
  • 12V/DC: Power input jack.

4.2. LED Indicators

The device includes two main indicator LEDs:

NameColorStatusDescription
POWERRedAlways onPower connected
POWERRedOffPower off
STATUSRedFlickerInput signal is normal
STATUSRedOffThe input signal is abnormal

5. Setup

5.1. Physical Connections

  1. Connect Video Sources: Connect your HDMI video sources (e.g., cameras, computers) to the HDMI IN ports (1-4) on the encoder using HDMI cables.
  2. Connect Audio Sources: If using external audio, connect your audio devices to the AUDIO IN ports (1-4). If using HDMI embedded audio, no separate audio connection is needed.
  3. Connect Power: Plug the provided 12V/DC power adapter into the encoder's 12V/DC port and then into a power outlet. The PWR LED should illuminate.
  4. Connect to Network: Connect the encoder's LAN port to your network router or switch using an Ethernet cable.
  5. Connect to Monitor (Optional): For initial setup or monitoring, you can connect the encoder to a display device (e.g., monitor, TV) via HDMI.
Diagram illustrating the application of the ORIVISION HDMI Encoder, showing connections from PC, Camera, Monitor, UAV to the encoder, then to the Internet for live platforms (YouTube, Facebook, Twitch, Livestream, Ustream, WOWZA) or to an ORIVISION Video Decoder and NVR for local display.
Figure 5.1: Connection Diagram

5.2. Network Configuration and Web Interface Access

To access the encoder's web interface for configuration, follow these steps:

  1. Direct PC Connection: Connect the encoder directly to your PC using an Ethernet cable.
  2. PC IP Address Setup:
    a. On your PC, go to "Network & Internet Settings".
    b. Select "Change adapter options" (or similar, depending on OS).
    c. Right-click on your "Local Area Connection" (or Ethernet adapter) and select "Properties".
    d. Select "Internet Protocol Version 4 (TCP/IPv4)" and click "Properties".
    e. Manually set your PC's IP address to be in the same subnet as the encoder's default IP. For example, if the encoder's default IP is 192.168.0.31, set your PC's IP to 192.168.0.30. Set the Subnet mask to 255.255.255.0. Click OK.
  3. Access Web Interface (Default IP): Open a web browser (e.g., Chrome, Firefox) and enter the encoder's default IP address: 192.168.0.31.
  4. Login: Enter the default credentials:
    Username: admin
    Password: admin
  5. Change Encoder IP (if necessary): If your router's network uses a different IP range (e.g., 192.168.10.XXX), you will need to change the encoder's IP address to match. Navigate to the Network settings within the encoder's web interface, change the IP to 192.168.10.XXX (e.g., 192.168.10.100), and set the Gateway and DNS to your router's IP (e.g., 192.168.10.1). Click "Apply" and then "Reboot" the encoder.
  6. Connect Encoder to Router: After changing the IP and rebooting, connect the encoder's LAN port to your network router. Connect your PC to the same network.
  7. Access Web Interface (New IP): Open a web browser and enter the encoder's new IP address (e.g., 192.168.10.100).

Note: If you cannot log in after changing the IP, check the DNS settings of your router and ensure they are correctly configured in the encoder. Then reset the encoder and re-login to modify the IP, gateway, and DNS.

6. Operating Instructions

6.1. Streaming to YouTube/Facebook via RTMP/RTMPS

  1. Pre-broadcast Checks:
    a. Verify the stream address in the encoder using a VLC player to confirm normal playback.
    b. If using a Canon camera, note that it may not have audio output; an external audio input might be required.
    c. Microphones are typically not direct audio sources for the encoder.
  2. Obtain Stream Key/URL: Log in to your YouTube or Facebook account, navigate to the "Go Live" section, and retrieve your unique Stream Key and Stream URL.
  3. Configure Encoder:
    a. In the encoder's web interface, go to the "Stream" section, then "Client", and select the "Rtmp(s)" page.
    b. Enable the RTMP protocol.
    c. Enter the Stream URL into the "Server addr" field and the Stream Key into the "Server app" field.
  4. Apply and Reboot: Click the "Apply" button at the bottom of the page, then go to the "Upgrade" page and click the "Reboot" button.

Troubleshooting Tip: If streaming fails, check your DNS settings. Ensure DNS0 and DNS1 values are set to your router's DNS addresses.

6.2. Setting up SRT Protocol

The encoder supports SRT (Secure Reliable Transport) protocol in both Caller and Listener modes.

6.2.1. Caller Mode (Encoder as Caller)

In this mode, the encoder initiates the connection to a Listener (e.g., a decoder). The SRT address format for the Video Decoder will be:

  • srt://ip:port
  • srt://ip:port?passphrase=passwords (for encrypted streams)

Example: srt://192.168.8.31:7120?passphrase=1234567890

6.2.2. Listener Mode (Encoder as Listener)

In this mode, the encoder waits for a Caller (e.g., another encoder or streaming software) to initiate the connection. The SRT address format for the Video Decoder will be:

  • srt://@:port?mode=listener
  • srt://@:port?mode=listener&passphrase=passwords (for encrypted streams)

Example: srt://@:7120?mode=listener&passphrase=1234567890

6.3. Text and Image Overlay

The encoder allows you to add self-defined text, time, and image overlays at any position on your video stream. This feature can be used to display copyrights, branding, or other information.

7. Maintenance

7.1. Firmware Upgrade

To ensure optimal performance and access to new features, it is recommended to keep your encoder's firmware updated.

  1. Obtain Firmware: Download the latest firmware file from the official ORIVISION website. Do not unzip the file.
  2. Access Upgrade Section: In the encoder's web interface, navigate to the "UPGRADE" section.
  3. Select Firmware File: Click "Choose File" (or similar) and select the downloaded firmware file (e.g., 1.2.10...0).img).
  4. Start Upgrade: Click the "Upgrade" button.
  5. Do Not Interrupt: During the upgrade process, do not refresh or close the webpage, and do not turn off the encoder.
  6. Reboot: Once the system prompts that the upgrade is successful, reboot your encoder to complete the installation.

Important: If the upgrade fails, do not reset the device immediately. Simply reboot it and try again.

8. Troubleshooting

8.1. Resetting the Encoder to Factory Settings

If you are unable to log in to the web interface or encounter persistent issues, you can restore the encoder to its factory default settings using one of the following methods:

Method 1: Hardware Reset (RST Button)
  1. Locate the recessed "RST" hole on the front panel of the encoder.
  2. Using a sharp, non-metallic object (like a straightened paperclip), insert it into the RST hole and press and hold for approximately 10 seconds.
  3. Release the button once all the indicator lights stop flashing.

The factory settings will be restored, including:

  • Default IP address: 192.168.0.31
  • Default username: admin
  • Default password: admin
  • All video/audio encoding settings will be reset.
Method 2: Software Reset (Web Interface)
  1. If you can access the web interface, navigate to the "BAKUP" section.
  2. Click the "Default" button to initiate the factory reset.
  3. Reboot the encoder after the process is complete.

Note: If your web page displays an upgrade prompt, please refer to the firmware upgrade instructions or contact support for guidance on restoring settings.

9. Specifications

ParameterValue
ModelZY-EH1304
Video Input4×HDMI 1.4
Support Resolution3840*2160, 1920*1080, 1920*960, 1680*1200, 1600*900, 1440*1050, 1440*900, 1360*768, 1280*720, 1280*800, 1280*768, 1024*768, 1024*576, 960*540, 850*480, 800*600, 720*576, 720
Frame Rate5-60Hz
HDCPSupport HDCP 1.4
Output Interface1×Ethernet port (RJ45)
Video EncodingH.265/H.264/Baseline Profile/Main profile/High Profile
Max Bitrate16kbps-12Mbps
Rate ControlCBR/VBR
Audio Input Interface4×External audio, HDMI built-in Audio
Audio EncodingACC, G711, LCAAC, EAAC, EAACPLUS
Bit-rate Option48K, 64K, 96K, 128K, 160K, 192K, 256K
Sampling Accuracy24 Bit
Audio Data-rate64Kb/s to 384Kb/s
Network1000M Ethernet port
ProtocolsSRT, HTTP, RTSP, RTMP/RTMPS, HLS, FLV, Multicast: UDP/RTP
Control PanelWeb panel (English language), remote upgrade
Firmware UpdateEnable by uploading files to the dashboard
Dimension238×122×28mm
Gross Weight0.4kg
Temperature0~45℃ (working), -20~60℃ (storing)
Humidity<90%, non-condensing
Power SupplyDC 12V/1A
Power Consumption<5W

10. Warranty and Support

For comprehensive details on warranty, technical support, and advanced configurations, please refer to the full User Manual (PDF) available at ORIVISION ZY-EH1304 User Manual (PDF).

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.