Flipsky 6374

Contents

Flipsky 6374 Waterproof Brushless DC Motor

User Manual

1. Introduction

This manual provides essential information for the safe and efficient operation, installation, and maintenance of your Flipsky 6374 Waterproof Brushless DC Motor. Designed for high-performance applications such as surfing boats, underwater thrusters, and hydro efoils, this outer rotor motor delivers significant power and reliability in aquatic environments.

Please read this manual thoroughly before using the product to ensure proper function and to prevent damage.

2. Specifications

Feature Specification
Model 6374
Dimensions (Diameter × Length) 63.0mm × 74mm
Shaft Diameter Φ10mm
KV Rating 140KV
Operating Voltage 8-16S (LiPo cells)
Max Power 3600 Watts
Rated Power 2400 Watts
Max Current 75 Amps
Rated Current (I/A) 50 Amps
Insulation Current AC500v/50Hz/1mA/3S
Resistance (R/mΩ) 44.9
Inductance (L/uH) 28.6
Three-phase Lead 3*12AWG (4.5mm)
Plug Type 4mm banana head (male)
Internal Structure 12N/14P
Waterproof Rating IP58

The IP58 rating indicates that the motor is protected from dust ingress and can withstand immersion in water up to 1 meter for 30 minutes.

3. Setup and Installation

3.1 Component Overview

Flipsky 6374 Motor Only
Figure 1: Flipsky 6374 Motor (Motor Only variant)
Flipsky 6374 Motor with 4.8 Propeller
Figure 2: Flipsky 6374 Motor with 4.8 Propeller (With 4.8 Propeller variant)
Flipsky 6374 Motor with long wires and banana connectors
Figure 3: Motor showing extended wiring with 4mm banana connectors.

3.2 Mounting the Motor

The motor features multiple mounting points on its end cap for secure attachment to your application. Refer to the technical drawings for precise dimensions and hole patterns.

Top view of Flipsky 6374 motor showing mounting holes
Figure 4: Top view of the motor, illustrating the shaft and mounting screw locations.

Ensure all mounting screws are tightened securely to prevent vibration and detachment during operation. Use appropriate hardware for your specific mounting surface.

3.3 Wiring Diagram and Connections

The motor comes with three-phase leads (3*12AWG) terminated with 4mm male banana connectors. These should be connected to a compatible Electronic Speed Controller (ESC).

Technical drawing of Flipsky 6374 motor with dimensions and wiring details
Figure 5: Technical drawing showing motor dimensions and wiring. The three-phase leads are labeled U (Blue), V (Green), and W (Yellow). The motor wire is 12AWG Silicone Line, with 4mm banana connectors. Overall length is 74±0.5mm, diameter is Φ63mm. Shaft diameter is Φ10mm. Mounting holes include 4-M4 and 4-M5 patterns.
Detailed technical drawing of Flipsky 6374 motor showing internal structure and mounting
Figure 6: Detailed technical drawing providing additional views of the motor, including mounting hole patterns (4-M4, 4-M5) and shaft details. The diagram shows a 45-degree angle for some mounting points and a 44±0.1mm diameter for the main mounting circle.

Connect the three motor wires to the corresponding phase outputs of your ESC. The order of connection may affect the motor's rotation direction. If the motor spins in the wrong direction, swap any two of the three phase wires.

Ensure all connections are secure and properly insulated, especially in waterproof applications, to prevent short circuits and water ingress.

4. Operating Instructions

This brushless DC motor requires an appropriate Electronic Speed Controller (ESC) for operation. The ESC converts the DC power from your battery into three-phase AC power to drive the motor and provides control signals.

  1. Power Supply: Connect your battery pack (8-16S LiPo recommended) to the ESC's power input. Ensure correct polarity.
  2. ESC Configuration: Configure your ESC according to its manufacturer's instructions. This typically involves setting parameters such as battery type, cut-off voltage, timing, and braking.
  3. Motor Connection: Connect the motor's three-phase wires to the ESC's motor outputs.
  4. Control Input: Connect the ESC's signal wire to your receiver or flight controller.
  5. Initial Test: Before full deployment, perform a low-power test to verify motor rotation direction and smooth operation. Adjust ESC settings or motor wire connections if necessary.
  6. Waterproof Integrity: For underwater applications, ensure all connections and openings are sealed to maintain the IP58 waterproof rating.

Caution: Always operate the motor within its specified voltage and current limits to prevent overheating and damage. Overloading the motor can lead to permanent failure.

5. Maintenance

  • Regular Inspection: Periodically inspect the motor for any signs of wear, corrosion, or damage, especially after use in saltwater environments.
  • Cleaning: After use, particularly in water, rinse the motor with fresh water to remove salt, sand, or debris. Allow it to dry completely before storage.
  • Shaft and Bearings: Check the motor shaft for any bends or damage. While the motor is designed for durability, extreme impacts can affect the bearings.
  • Wiring: Ensure all wires and connectors are in good condition, free from fraying or corrosion.
  • Storage: Store the motor in a dry, cool place away from direct sunlight and corrosive materials.

6. Troubleshooting

Problem Possible Cause Solution
Motor does not spin No power to ESC; ESC not armed; Motor wires disconnected; Faulty ESC or motor. Check battery connection and charge; Ensure ESC is armed (refer to ESC manual); Verify motor wire connections; Test with a known good ESC/motor if possible.
Motor spins in wrong direction Incorrect phase wire connection. Swap any two of the three motor phase wires connected to the ESC.
Motor stutters or runs roughly Loose motor wire connection; Incorrect ESC timing; Damaged motor winding. Check all motor wire connections; Adjust ESC timing settings (start with medium); Inspect motor for physical damage.
Motor overheats Overloading; Insufficient cooling; Incorrect ESC settings. Reduce load; Ensure adequate water flow for cooling; Check ESC timing and current limits.
Water ingress Improper sealing; Damage to motor casing. Ensure all connections and entry points are properly sealed for waterproof applications. Inspect motor for cracks or damage.

7. User Tips

  • ESC Compatibility: This motor does not come with an Electronic Speed Controller (ESC). You will need to purchase a compatible ESC separately. Ensure the ESC can handle the motor's maximum current (75 Amps) and voltage (8-16S).
  • Propeller Selection: If your motor did not come with a propeller, choose one that is appropriate for your application and motor's KV rating. An oversized propeller can lead to motor overheating and inefficiency.
  • Cooling: For high-power applications, ensure your setup provides adequate cooling for both the motor and the ESC. While the motor is waterproof, efficient heat dissipation is crucial for longevity.

8. Warranty and Support

For warranty information and technical support, please refer to the official Flipsky website or contact your retailer. Keep your purchase receipt as proof of purchase.

This product is intended for experienced users. Improper installation or use may void the warranty.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.