FSTE KT-16A

Contents

FSTE KT-16A E-Bike Controller Instruction Manual

Model: KT-16A | For 36V/48V E-Bike Motor Conversion

1. Introduction

This manual provides essential information for the installation, operation, and maintenance of your FSTE KT-16A Sine Wave E-Bike Controller. This controller is designed for electric bicycle motor conversion kits, specifically for 250W/350W brushless motors, and operates with universal 36V/48V systems. It features a 6-tube sine wave design for efficient and stable performance.

FSTE KT-16A E-Bike Controller
Figure 1: FSTE KT-16A E-Bike Controller, front view.

2. Specifications

Product dimensions and specifications for KT-16A controller
Figure 2: Product dimensions and key specifications.
FeatureDetail
TypeKT 16A General Controller
Rated Voltage36V / 48V (Universal)
Low Voltage ProtectionDC30/40 ± 0.5V
FET (Field-Effect Transistor)Large 6-tube
Maximum Current16 ± 1A
Rated Current8A
Speed Set1-4.2V
Brake InputLow Level
Dimensions (L x W x H)80 x 51 x 30 mm
Weight213.6g
MaterialMetal
ColorBlack

3. Setup and Installation

The FSTE KT-16A controller is designed for straightforward installation. Please follow these guidelines carefully:

  1. Compatibility Check: Ensure your existing e-bike system, especially the display, uses a KT controller (communication protocol). This controller is only compatible with KT series accessories, such as KT LCD displays.
  2. Connector Identification: Identify the various connectors on the controller and match them to your e-bike components. Refer to the diagram below for common plug types.
    Wiring diagram for KT-16A controller showing various plug types and their functions
    Figure 3: Introduction to Ordinary Plugs (KT 16A Controller).
    • Motor: 9-pin connector
    • Lamp Wire: 2-pin connector
    • Throttle: 3-pin connector
    • Support (PAS Sensor): 3-pin connector
    • Power Supply: 2-pin connector
    • Instrument (Display): 5-pin connector
    • Brake: 2-pin connector
  3. Wiring Sequence: Pay close attention to the wiring sequence. While the connectors are standard SM type, variations in wire sequence can affect compatibility. The manufacturer cannot guarantee 100% compatibility if the wire sequence differs significantly from standard.
  4. Secure Connections: Ensure all connectors are properly seated and secured. A properly connected system should function correctly in approximately 90% of cases.
  5. Waterproof Connectors: If your e-bike system requires waterproof connectors, note that this controller uses standard SM plugs. Waterproof connectors are specialized and may require different components.

Important Reminder: Before installation, verify that your original controller is a KT controller (communication protocol). This controller is specifically designed for KT series accessories. If you encounter any problems during the installation process, please consult a professional or contact customer support.

4. Operating Instructions

Once correctly installed and connected to a compatible KT LCD display and motor, the controller will manage the power delivery to your e-bike motor. The sine wave technology ensures a smooth, quiet, and efficient operation, enhancing your riding experience.

  • The controller works with 36V or 48V battery systems.
  • It is suitable for 250W and 350W brushless motors.
  • The KT LCD display (not included) will provide interface for speed settings, battery level, and other parameters.
E-bike controller in use, highlighting sine wave efficiency
Figure 4: Sine wave controllers offer high efficiency and stability for a better riding experience.

5. Maintenance

To ensure the longevity and optimal performance of your FSTE KT-16A controller, consider the following maintenance tips:

  • Keep Dry: Protect the controller from water and excessive moisture. While the casing offers some protection, it is not fully waterproof unless specified.
  • Cleanliness: Periodically clean the exterior of the controller with a dry, soft cloth to prevent dust and dirt buildup, which can affect heat dissipation.
  • Connection Integrity: Regularly check all wire connections to ensure they are secure and free from corrosion. Loose connections can lead to intermittent operation or damage.
  • Avoid Physical Damage: Mount the controller in a location where it is protected from impacts and vibrations.
  • Temperature: Avoid operating the e-bike in extreme temperatures for prolonged periods, as this can stress electronic components.

6. Troubleshooting

If you encounter issues with your FSTE KT-16A controller, consider the following troubleshooting steps:

  • No Power/No Response:
    • Check battery connections and ensure the battery is charged.
    • Verify all power supply wires are correctly connected and secure.
    • Ensure the display is properly connected and powered on.
  • Motor Not Functioning Correctly:
    • Confirm that the motor's 9-pin connector is fully engaged.
    • Check the throttle and PAS sensor connections.
    • Ensure the controller is compatible with your motor's wattage (250W/350W recommended).
  • Display Errors:
    • Ensure your display is a KT series LCD display, as this controller uses the KT communication protocol.
    • Check the 5-pin instrument connector for proper connection.
  • Intermittent Operation:
    • Inspect all connectors for looseness or corrosion.
    • Ensure no wires are pinched or damaged.

Note: Due to potential differences in product appearance, color, or printed text across manufacturing batches, these variations will not affect the controller's functionality. If problems persist after basic troubleshooting, professional assistance is recommended.

7. User Tips

  • Always double-check the voltage compatibility (36V/48V) with your battery and motor before connecting.
  • When replacing an old controller, ensure the new FSTE KT-16A controller's communication protocol and connector types (especially wire sequence) are compatible with your existing e-bike components, particularly the display.
  • For optimal performance, keep the controller mounted in a well-ventilated area to aid in heat dissipation.

8. Warranty and Support

For any technical assistance, warranty claims, or further inquiries, please contact the seller or manufacturer directly. Keep your purchase records for reference.

© 2023 FSTE. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.