BRZHIFI DA10PRO

Contents

BRZHIFI DA10PRO Dual-core AK4499EX Full-balanced Decoder

Model: DA10PRO

User Manual

1. Introduction

The BRZHIFI DA10PRO is a high-performance audio decoder designed to deliver an exceptional HIFI audio experience. Featuring a dual-core AK4499EX decoding chip and an FPGA processing chip, it supports a wide range of high-resolution audio formats including DSD512 and PCM 384KHz/32BIT. With its robust pre-amplifier and powerful headphone driving capabilities, the DA10PRO is compatible with various high-end headphones and stereo equipment, ensuring an original and enjoyable music experience.

Front view of the BRZHIFI DA10PRO decoder

Front view of the BRZHIFI DA10PRO decoder, showcasing its sleek design.

2. Key Features

  • Dual-core AK4499EX Decoding Chip: Utilizes two flagship AK4499EX chips for superior digital-to-analog conversion.
  • FPGA Processing Chip: Advanced programming logic device for enhanced audio processing.
  • High-Resolution Audio Support: Supports DSD up to DSD512 and PCM up to 32BIT/384KHz.
  • Femtosecond Clock Crystal Oscillator: Ensures precise timing for accurate sound reproduction.
  • Italian USB Digital Interface: High-quality USB sub-card for optimal PC audio connection.
  • Versatile Inputs: Includes USB-PC (OTG), Optical, Coaxial, AES/EUB, I2S-HDMI, AUX analog signal, and Bluetooth 5.1.
  • Balanced and Single-ended Outputs: XLR balanced and RCA single-ended outputs for flexible connectivity.
  • Powerful Headphone Amplifier: Capable of driving headphones with impedance from 32Ω to 600Ω.
  • Infrared Remote Control: Convenient control over device functions.
  • OLED Display: Clear and intuitive display for operational status.
  • Multiple Digital Filtering Modes: Offers 6 types of PCM digital filters for sound customization.
  • Bluetooth 5.1: Supports high-quality codecs like LDAC, APTX-HD, APTX, SBC, AAC.
Diagram showing HIEND flagship features like AKM DAC, FPGA, DSD512, IIS-H, PCM 32BIT/384K, Italian USB, Balanced Output, Remote Control, OLED Display, CCHD, Digital Filters, and Bluetooth 5.0.

Overview of the DA10PRO's HIEND flagship features.

3. Package Contents

Please check the package for the following items:

  • BRZHIFI DA10PRO Decoder Unit
  • Infrared Remote Control
  • Bluetooth Antenna
  • Power Cable

4. Setup Guide

4.1 Physical Placement

Place the DA10PRO on a stable, flat surface with adequate ventilation. Avoid placing it near heat sources or in direct sunlight. Ensure sufficient space around the unit for proper airflow.

4.2 Power Connection

  1. Ensure the power switch on the rear panel is in the OFF position.
  2. Connect the provided power cable to the AC inlet on the rear of the DA10PRO.
  3. Plug the other end of the power cable into a suitable 110V/220V AC power outlet. The unit features dual 25W customized transformers for stable power delivery.

4.3 Input Connections

The DA10PRO offers a variety of digital and analog input options. Refer to the rear panel diagram below for port locations:

Rear panel connections of the DA10PRO decoder, showing XLR, RCA, AES/EUB, Coaxial, Optical, PC-USB, IIS-HDMI, Bluetooth antenna, and power input.

Rear panel connections and remote control layout.

  • USB-PC (OTG): Connect your computer or OTG-compatible device using a USB-B cable. The USB input socket is a standard USB-B female socket, and the USB power supply range is 4.5V-5.1V.
  • Optical (OPT): Connect to digital audio sources via an optical fiber cable.
  • Coaxial (COAX): Connect to digital audio sources via a coaxial cable. The S/PDIF interface inputs standard S/PDIF signals, with an input impedance of 75Ω.
  • AES/EUB: Connect to professional digital audio sources. The AES input impedance is 110Ω.
  • I2S-HDMI: Connect to compatible digital interfaces. Note: This is an audio I2S differential signal interface and is NOT a standard HDMI interface for TVs. Please select a digital interface or turntable with an HDMI interface and ensure the line sequence is consistent. Incorrect connection may cause damage.
  • AUX Analog Input: For analog audio sources.
  • Bluetooth 5.1: Screw the provided Bluetooth antenna onto the designated connector on the rear panel.

4.4 Output Connections

  • XLR Balanced Output: Connect to balanced amplifiers or active speakers using XLR cables. The XLR interface definition is European and Japanese standard: 1 ground, 2 cold, 3 hot.
  • RCA Single-ended Output: Connect to single-ended amplifiers or active speakers using RCA cables.
  • Headphone Amplifier Output: Plug your headphones into the 6.35mm headphone jack on the front panel.

4.5 I2S-LVDS(HDMI) Pin Definition

For users utilizing the I2S-HDMI input, it is crucial to understand the pin definition to ensure correct wiring and prevent damage. The I2S input uses LVDS levels in the form of an HDMI interface, compatible with most front-end equipment.

Diagram illustrating the IIS-LVDS(HDMI) pin definition for the DA10PRO decoder.

IIS-LVDS(HDMI) Pin Definition Diagram.

5. Operating Instructions

5.1 Front Panel Controls

The front panel provides direct access to essential functions:

Front panel of the DA10PRO decoder with labels for power switch, OLED display, volume controls, input selection, filter selection, standby light, remote receiver, screen brightness, mute, and headphone output.

Front panel function introduction.

  • Power Switch: Turns the unit ON/OFF.
  • OLED Display: Shows current input, sampling rate, volume, and filter settings.
  • Volume Down (-): Decreases the output volume.
  • Input Selection: Cycles through available input sources (USB, Optical, Coaxial, AES/EUB, I2S-HDMI, AUX, Bluetooth).
  • Filter Selection: Changes the digital filter mode (see section 5.3).
  • Standby/Light: Puts the unit into standby mode or adjusts display brightness.
  • Remote Control Receiving Hole: Infrared receiver for the remote control.
  • Screen Brightness: Adjusts the brightness of the OLED display.
  • Mute: Mutes/unmutes the audio output.
  • Volume Plus (+): Increases the output volume.
  • Headphone Amplifier Output: 6.35mm jack for headphone connection.

5.2 Remote Control Functions

The included infrared remote control provides convenient operation from a distance:

Remote control layout with buttons for Boot/shutdown, Filter, Mute, Brightness, Input-side selection, Volume reduction, and Volume increase.

Remote control layout.

  • Boot/Shutdown: Powers the unit ON/OFF or puts it into standby.
  • Filter: Cycles through digital filter modes.
  • Mute: Toggles audio mute.
  • Brightness: Adjusts OLED display brightness.
  • Input-side Selection: Selects the active input source.
  • Volume Reduction (-): Decreases volume.
  • Increase the Volume (+): Increases volume.

5.3 Digital Filtering (PCM)

The DA10PRO offers 6 types of digital filters for PCM playback, allowing you to fine-tune the sound to your preference:

  • Sharp Roll-off
  • Slow Roll-off
  • Short Delay Sharp Roll-off
  • Short Delay Slow Roll-off (NOS-like)
  • Low Dispersion Short Delay Filter
  • (Sixth filter type not explicitly named, but implied by '6 types')
Image showing 'Digital filtering: PCM 6 types' and listing the filter names.

Digital filtering options for PCM.

6. Specifications

Table of product parameters including input/output modes, THD+N, SNR, headphone amp specs, dimensions, weight, power consumption, sampling rates, bit width, Bluetooth protocols, and electrical standards.

Detailed product parameters.

General

Parameter Value
Input Modes USB-PC (OTG), Optical Fiber, Coaxial, AES/EUB, I2S-HDMI, AUX Analog Signal, Bluetooth 5.1
Output Modes RCA Single-ended Line, XLR Balanced Line
THD+N >0.0001%@1KHz
Signal-to-Noise Ratio (RCA) >127DB
Signal-to-Noise Ratio (XLR) 133DB
Headphone Amp Power 2000MW
Headphone Resistance 32-600Ω
XLR Interface Definition European and Japanese standard (1 ground, 2 cold, 3 hot)
Dimensions (L*W*H) 344mm * 266mm * 55mm (manual measurement)
Weight 4.1KG
Machine Power Consumption >30W
Bluetooth Protocol LDAC, APTX-HD, APTX, SBC, AAC

Sampling Rates & Bit Width

Interface PCM (KHz) DSD (Native) DSD (DOP) Bit Width
USB, I2S-HDMI 44.1-384 DSD64-DSD512 DSD64-DSD128 Up to 32BIT
AES/EUB, Coaxial 44.1-192 Not supported DOP64 Up to 24 BIT
Optical (OPT) 44.1-192 Not supported Not supported Up to 24 BIT
Decoding parameter table showing PCM, DSD (Native), and DSD (Dop) support for USB/IIS-HDMI, AES/EUB/Coax, and OPT interfaces.

Decoding parameter table.

AK4499EX Chip Parameters

  • 4 channels (AK4497EQ is 2 channels)
  • THD+N: -124DB (AK4497EQ is -116DB)
  • Signal-to-noise ratio of a single channel: 140DB (AK4497EQ is 131DB)
  • 6 kinds of digital filters
  • Power: 667MW (AK4497EQ is 346MW)
  • 128-pin H TQFP package (AK4497EQ is a 64-pin TQFP package)
  • Current output architecture (AK4497EQ is voltage output architecture)
Image detailing AK4499EX*2 chip information and parameters.

AK4499EX chip details and parameters.

7. Troubleshooting

  • No Power:
    • Ensure the power cable is securely connected to both the DA10PRO and the power outlet.
    • Check that the power switch on the rear panel is in the ON position.
    • Verify the power outlet is functional.
  • No Signal/No Sound:
    • Confirm that the correct input source is selected on the DA10PRO (check the OLED display).
    • Ensure all audio cables (USB, Optical, Coaxial, AES/EUB, I2S-HDMI, RCA, XLR, headphone) are securely connected.
    • Check the volume level on the DA10PRO and your connected amplifier/headphones.
    • Ensure the unit is not muted.
    • For I2S-HDMI, verify the pin definition and compatibility with your source device.
  • Bluetooth Connection Issues:
    • Ensure the Bluetooth antenna is properly attached.
    • Check that Bluetooth is enabled on your source device and the DA10PRO is in pairing mode.
    • Try restarting both the DA10PRO and your Bluetooth source device.

8. Maintenance

  • Cleaning: Use a soft, dry cloth to clean the exterior of the unit. Avoid using abrasive cleaners, solvents, or chemical sprays.
  • Environment: Keep the DA10PRO in a dry, dust-free environment. Avoid extreme temperatures and high humidity.
  • Ventilation: Ensure that the ventilation openings are not blocked to prevent overheating.
  • Power Off: If the unit will not be used for an extended period, disconnect it from the power supply.

9. User Tips

  • Cable Quality: For optimal audio performance, invest in high-quality digital and analog interconnect cables.
  • Headphone Matching: When using the headphone output, ensure your headphones' impedance falls within the recommended 32-600Ω range for the best sound quality and power delivery.
  • Experiment with Filters: Explore the different PCM digital filter modes to find the sound signature that best suits your listening preferences and music genre.
  • Firmware Updates: Periodically check the manufacturer's website for any available firmware updates to ensure your device has the latest features and performance enhancements.

10. Warranty and Support

For warranty information, technical support, or service inquiries, please contact the seller or authorized distributor from whom you purchased the BRZHIFI DA10PRO. Please retain your proof of purchase for warranty claims.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.