MESTEK CM83A, CM83B

Contents

MESTEK Digital Clamp Meter CM83A/CM83B Instruction Manual

Your guide to safe and effective use of your MESTEK Digital Clamp Meter.

1. Introduction

The MESTEK Digital Clamp Meter, available in models CM83A and CM83B, is a professional-grade electrical testing instrument designed for a wide range of measurements. It features a new chip design for fast response, easy operation, and an anti-burn design for enhanced safety. This manual provides essential information for the proper and safe use of your device.

Image showing both CM83A and CM83B models side-by-side, highlighting the new chip design and upgrade generation.
Figure 1: MESTEK CM83A and CM83B Digital Clamp Meters

2. Safety Information

Always adhere to basic safety precautions when using this product to reduce the risk of fire, electric shock, or personal injury. This device complies with GB4793.1-1995 (IEC-61010) electronic measurement instrument safety requirements and features overload protection up to CATIII 600V.

  • Do not exceed the maximum input values specified for each measurement function.
  • Ensure the meter is in the correct function and range before making measurements.
  • Inspect test leads for damage before use. Do not use if insulation is damaged.
  • Avoid using the meter in wet environments or during electrical storms.
  • Always turn off power to the circuit and discharge high-voltage capacitors before measuring resistance, continuity, diodes, or capacitance.
  • Use caution when working with voltages above 60V DC or 30V AC RMS, as they pose a shock hazard.

3. Setup

3.1 Battery Installation

  1. Ensure the device is powered off.
  2. Locate the battery compartment cover on the back of the meter.
  3. Use a screwdriver to open the cover.
  4. Insert two (2) AAA batteries, observing correct polarity (+/-). (Batteries are not included).
  5. Replace the battery compartment cover and secure it with the screw.

3.2 Connecting Test Probes

For voltage, resistance, capacitance, continuity, and diode measurements, connect the test probes:

  1. Insert the red test lead into the 'INPUT' jack.
  2. Insert the black test lead into the 'COM' (common) jack.
Image showing the CM83B clamp meter along with its accessories: a pair of 10A probes and a carrying bag.
Figure 2: Clamp Meter with Test Probes and Carrying Bag

4. Operating Instructions

4.1 Power On/Off

Turn the rotary switch to the desired function to power on the meter. Turn it to 'OFF' to power off. The meter features an auto power-off function to conserve battery life.

4.2 Function Selection

Rotate the central dial to select the desired measurement function. The CM83A model uses manual ranging, while the CM83B features auto-ranging for convenience.

Comparison image of CM83A and CM83B models, emphasizing their different functions and specifications.
Figure 3: CM83A and CM83B Function Comparison

4.3 Measuring AC Current (Clamp Function)

  1. Select the AC Current (A) function on the rotary switch.
  2. Open the clamp jaw by pressing the trigger.
  3. Enclose a single conductor (not a bundle of wires) within the jaw.
  4. Ensure the jaw is fully closed.
  5. Read the AC current value on the LCD display.
Image demonstrating the 30mm jaw opening of the clamp meter, indicating its practical use for various conductor sizes.
Figure 4: Demonstrating the 30mm Jaw Opening

4.4 Measuring AC/DC Voltage

  1. Select the ACV or DCV function.
  2. Connect the test leads in parallel to the circuit or component to be measured.
  3. Read the voltage value on the LCD display.

4.5 Measuring Resistance (Ω)

  1. Select the Resistance (Ω) function.
  2. Ensure the circuit is de-energized.
  3. Connect the test leads across the component.
  4. Read the resistance value.

4.6 Measuring Capacitance

  1. Select the Capacitance function.
  2. Ensure the capacitor is fully discharged before connecting the test leads.
  3. Connect the test leads across the capacitor.
  4. Read the capacitance value.

4.7 Continuity/Diode Test

  1. Select the Continuity/Diode function.
  2. For continuity, connect test leads across the circuit. A beep indicates continuity.
  3. For diode test, connect leads across the diode. The display will show the forward voltage drop.

4.8 NCV (Non-Contact Voltage) Detection

  1. Select the NCV function.
  2. Bring the top of the meter close to the conductor.
  3. The meter will indicate the presence of AC voltage without physical contact.

4.9 Data Hold

Press the 'HOLD' button to freeze the current reading on the display. Press again to release.

4.10 Backlight/Flashlight

Press the backlight button (often marked with a lightbulb or asterisk symbol) to turn on the display backlight or the clamp flashlight. Press again to cycle or turn off.

4.11 CM83B Specific Functions

The CM83B model offers advanced features:

  • True-RMS: Provides accurate AC measurements for non-sinusoidal waveforms.
  • AUTO-VLoZ: Low impedance voltage measurement to prevent ghost voltages.
  • RCD Leakage Current Check: For testing residual current devices.
  • VFD (Variable Frequency Drive) Test: For measuring frequency and voltage on VFD circuits.
Close-up image of the CM83B display showing AC voltage and frequency measurements simultaneously, highlighting True-RMS for accurate readings.
Figure 5: CM83B Display with True-RMS and VFD Indication

5. Maintenance

5.1 Cleaning

Wipe the meter with a dry, soft cloth. Do not use abrasives or solvents. Keep the display clean for optimal readability.

5.2 Storage

When not in use for extended periods, remove the batteries to prevent leakage. Store the meter in a cool, dry place, away from direct sunlight and extreme temperatures. Recommended storage temperature: -10~50℃ (14~122℉); humidity: <70%RH.

5.3 Battery Replacement

When the low battery indicator appears on the display, replace the batteries promptly to ensure accurate measurements.

6. Troubleshooting

  • No display or faint display: Check battery installation and replace batteries if necessary.
  • Inaccurate readings: Ensure correct function and range selection. Check test lead connections. Verify batteries are not low.
  • Meter does not respond: Turn the meter off and then on again. If the issue persists, remove and reinsert batteries.

For persistent issues, contact customer support.

7. Specifications

FeatureCM83ACM83B
MaterialABS
ColorBlack
AC Current (A)0~6A/60A/600A0~1A/10A/100A/600A
AC Current Accuracy±3.0%+6 digits
AC Voltage (V)0~100V/600V
AC Voltage Accuracy±1.0%+3 digits
DC Voltage (V)0~100V/600V
DC Voltage Accuracy±0.8%+3 digits
Resistance (Ω)0~6000Ω0~1KΩ/10KΩ/100KΩ/10MΩ
Resistance Accuracy±1.2%+3 digits
Capacitance0~600μF/6000μF
Capacitance Accuracy±4.0%+5 digits
Display Counts6000 counts10000 counts
RangingManual RangeAuto Range
Continuity/DiodeAuto distinguish
NCV (Non-Contact Voltage)Yes
Clamp FlashlightYes
BacklightYes
Auto Power OffYes
Data HoldYes
True-RMSNoYes
RCD TestNoLeakage current switch conservation test
AUTO-VLoZNoLow impedance voltage measurement
VFDNoVariable frequency current test
FrequencyNoTest frequency with AC current range
Working Environment0~40℃ (32~104℉); <80%RH
Storage Temperature-10~50℃ (14~122℉); <70%RH
Battery2 * AAA battery (not included)
Jaw Opening30mm
Safety ComplianceGB4793.1-1995 (IEC-61010), CATIII 600V

8. User Tips

  • The new chip design ensures a fast response time, making your measurements quicker and more efficient.
  • The anti-burn design provides an extra layer of safety during operation.
  • The 30mm jaw opening is highly practical, allowing for easy clamping around various conductor sizes in different applications.
  • The large LCD screen with a high-contrast backlight ensures clear digital readings, even in dimly lit environments.
  • These meters are suitable for a variety of professional and educational settings, including electromechanical maintenance, air conditioning repair, and general electrical maintenance.

9. Warranty and Support

For any questions, technical support, or warranty claims, please refer to the contact information provided by your retailer or the manufacturer's official website. Keep your purchase receipt as proof of purchase.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.