DIVEDEER RN2-17

Contents

DIVEDEER RN2-17 Window Cleaning Robot User Manual

Model: RN2-17

1. Introduction

The DIVEDEER RN2-17 is a fully automatic window cleaning robot designed to efficiently clean various glass surfaces. Featuring bidirectional water spray, intelligent path planning, and robust safety mechanisms, it simplifies the task of window cleaning, especially for high or hard-to-reach areas. This manual provides essential information for the safe and effective use, maintenance, and troubleshooting of your device.

Front view of the DIVEDEER RN2-17 window cleaning robot, highlighting its double water spray feature.

Figure 1: DIVEDEER RN2-17 Window Cleaning Robot with Double Water Spray

2. Safety Information

  • Always bind the safety rope securely when using the robot to prevent falling from high altitudes.
  • Ensure the power cord is properly connected using the nut-type power failure proof connector to prevent accidental disconnection.
  • The robot is equipped with a UPS (Uninterruptible Power Supply) system that provides power for approximately 20 minutes in case of a power outage, allowing time for safe retrieval.
  • Do not use the robot on cracked or damaged glass surfaces.
  • Keep hands and loose clothing away from moving parts during operation.
  • This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
Infographic showing the nut-type power failure proof connector with a 4m extension cord, a safety rope with buckle (80KG tensile strength), and a powerful brushless motor.

Figure 2: Safety Features and Components

3. Product Configuration

Before setup, ensure all components are present in the package:

  • 1 x Robot Host
  • 1 x Power Cord + Adapter
  • 1 x Remote Control
  • 2 Pairs of Cleaning Rings
  • 1 x 4-meter Extension Cable
  • 1 x Safety Rope
  • 10 x Cleaning Cloths
  • 1 x Instruction Manual (or English manual)
  • 1 x Add Water Bottle
Diagram illustrating the components included in the product package: host, adapter + power cable, remote control, cleaning rings, extension cable, safety rope, cleaning cloths, and manual.

Figure 3: Product Package Contents

4. Setup Instructions

  1. Attach Cleaning Rags: Securely attach the provided cleaning cloths to the cleaning rings on the underside of the robot.
  2. Fill Water Tank: Open the water tank cap and fill the 50ml water tank with clean water or a suitable window cleaning solution using the add water bottle. Ensure the cap is closed tightly.
  3. Connect Power: Connect the power adapter to the robot's power port and then plug it into a power outlet. Ensure the nut-type connector is tightened.
  4. Attach Safety Rope: Securely attach one end of the safety rope to the safety rope hanging hole on the robot and the other end to a sturdy anchor point indoors, such as a heavy furniture leg or a window frame anchor.
  5. Initial Charging: If the robot is not fully charged, the orange light will indicate charging. Wait until the green light illuminates, indicating charging is complete.
Detailed diagram of the robot's top panel and underside, labeling the power button, indicator lights (blue, red, orange, green), remote control receiving window, water jet nozzles, cleaning rags, power port, and safety rope hanging hole.

Figure 4: Product Details and Components

5. Operating Instructions

  1. Placement: Place the robot firmly on the window surface you wish to clean. Ensure the surface is relatively clean and dry before placement for optimal suction.
  2. Start Cleaning: Press the 'One button start' switch on the robot or the corresponding button on the remote control.
  3. Glass Detection: Wait approximately 20 seconds after starting up until the blue light stops flashing. This indicates the robot has successfully detected the glass plane and is ready to begin working.
  4. Select Cleaning Mode: Use the remote control to select one of the three available cleaning modes:
    • First up then down (Z-path): Cleans from top to bottom in a Z-shaped pattern.
    • First left then left (N-path): Cleans from left to right, then moves down and cleans left to right again.
    • First right then right (Reverse N-path): Cleans from right to left, then moves down and cleans right to left again.
  5. Water Spraying Mode: Choose between manual or automatic water spraying via the remote control. The robot features a double-hole two-way water spray system for efficient cleaning.
  6. Automatic Path Planning: The robot utilizes an intelligent detection system for collision prevention and automatic path planning, ensuring thorough coverage and avoiding obstacles.
Image of a hand pressing the one-button start on the robot, indicating easy operation.

Figure 5: One-Click Start for Automatic Execution

Diagrams illustrating the three cleaning modes: Z-path (First up then down), N-path (First left then left), and reverse N-path (First right then right).

Figure 6: Three Cleaning Modes

Diagram showing the two-way water spraying mechanism, with arrows indicating spray direction based on robot movement.

Figure 7: Two-Way Water Spraying Mechanism

6. Maintenance

  • Cleaning Rags: After each use, remove the cleaning cloths from the rings. They are reusable and can be hand-washed or machine-washed. Ensure they are clean and dry before reattaching for the next use.
  • Water Tank: Empty any remaining water or cleaning solution from the 50ml water tank and rinse it thoroughly. Allow it to air dry to prevent mold or residue buildup.
  • Robot Exterior: Wipe down the robot's exterior with a soft, dry cloth to remove any dust or smudges. Do not use abrasive cleaners or immerse the robot in water.
  • Storage: Store the robot and its accessories in a clean, dry place away from direct sunlight and extreme temperatures.
Close-up of the 50ml water tank.

Figure 8: 50ml Large Water Tank

7. Troubleshooting

  • Robot not starting or blue light flashing continuously: The robot needs approximately 20 seconds to detect the glass plane after startup. Wait for the blue light to stop flashing before it begins cleaning.
  • Red light indicator: A red light indicates an abnormal condition. Check for any obstructions on the window, ensure the robot is properly placed, and that the cleaning rags are not excessively dirty or wet. If the issue persists, power cycle the device.
  • Robot falling or losing suction: Ensure the safety rope is always attached. Check that the window surface is clean and free of excessive moisture or debris that could compromise suction. The robot has 2800Pa suction power.
  • Ineffective cleaning: Ensure the cleaning rags are clean and slightly damp. For better results, spray some water on the edge of the mop when working.
  • Power failure protection: In case of a power outage, the robot's built-in UPS will maintain suction for about 20 minutes. Retrieve the robot manually during this period.
  • General issues: If you encounter problems such as product damage or inability to use the product after receiving the goods, please contact customer service. Provide a complete unboxing video and a video showing that the machine still cannot be used after operating according to the instructions for prompt assistance.
Image showing the robot on a window with a battery icon, explaining UPS power off protection for 20 minutes.

Figure 9: UPS Power Failure Protection

8. Specifications

ParameterValue
Input VoltageAC100 to 240V 50Hz to 60Hz
Rated Power Rating80W
Battery Capacity500mAh
Overall Dimensions295*145*62mm
Suction Power2800Pa
Net Weight980g
UPS Power Failure Protection Time20 minutes
Mode of ControlInfrared Remote Control
Noise LevelApproximately 60dB
Border DetectionAutomatic
Fall Protection ControlUPS uninterruptible power supply system/safety cord
Cleaning ModesThree kinds
Water Spraying ModeManual/Automatic
CertificationROHS
Table detailing the product parameters and specifications of the window cleaning robot.

Figure 10: Product Parameters

Image depicting the robot working on a window next to a sleeping baby, emphasizing its low noise level (60dB).

Figure 11: Low Decibel Operation (approx. 60dB)

Side view of the robot on a window, showing its ultra-thin body (6.2cm) and ability to clean windows with guardrails.

Figure 12: Ultra-thin Body (6.2cm)

9. Warranty and Support

The DIVEDEER RN2-17 window cleaning robot has passed CE, FCC, and ROHS quality testing and certification, and its power supply meets CCC, CE, FCC, UL, and ROHS safety standards.

For any product damage or operational issues, please contact customer service. To facilitate a quick resolution, please provide:

  • A complete unboxing video of the product.
  • A video demonstrating the issue, showing that the machine still cannot be used after operating according to the instructions in this manual.

10. User Tips

  • For optimal cleaning performance, slightly dampen the edges of the cleaning rags before attaching them to the robot. This can help achieve a better cleaning effect.
  • Always ensure the safety rope is securely fastened to both the robot and a stable anchor point, especially when cleaning windows at height.
  • Regularly clean the water tank and replace cleaning cloths to maintain hygiene and efficiency.
  • The robot's low noise level (around 60dB) allows for cleaning without significant disturbance, even in quiet environments.

© 2024 DIVEDEER. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.