MAT-TUNER mAT-30

Contents

MAT-TUNER mAT-30 Automatic Antenna Tuner

User Instruction Manual

1. Introduction

The mAT-30 Automatic Antenna Tuner is designed for use with Yaesu mobile radios, offering seamless compatibility with original Yaesu antenna tuners. This tuner is suitable for a wide range of transceivers, including but not limited to FT-100, FT-857D, FT-897D, FT-450D, FT-891, FT-991, and FT-950. Its operation is designed to be as straightforward and convenient as using the original equipment.

The mAT-30 can effectively tune various antenna types, such as dipole antennas (horizontal, inverted V, V, Yagi, frame) and monopole antennas (long-wire, inclined, whip). It offers enhanced performance compared to typical built-in antenna tuners, capable of tuning antennas with a VSWR over 3, particularly noted for the FT-891 HF transceiver where other tuners, including the original FC-50, may not succeed.

MAT-TUNER mAT-30 Automatic Antenna Tuner with data cable

Figure 1: MAT-TUNER mAT-30 Automatic Antenna Tuner with included data cable.

2. Setup and Connections

Before operating the mAT-30, ensure all connections are secure and correct. Refer to Figure 2 for a diagram of the rear panel connections.

Rear panel connections of MAT-TUNER mAT-30

Figure 2: Rear panel connections (ANTENNA, RF IN, GND, AUXILIARY POWER, RADIO).

  1. Connect the Antenna: Connect your antenna cable to the ANTENNA connector on the rear panel of the mAT-30.
  2. Connect RF Input: Connect the RF output from your transceiver to the RF IN connector on the rear panel of the mAT-30.
  3. Connect Data Cable: Use the dedicated data cable provided to connect the RADIO port on the mAT-30 to the antenna tuner interface on your Yaesu transceiver. This cable also supplies power to the tuner, eliminating the need for an additional power supply in most cases.
  4. Ground Connection (Optional but Recommended): Connect a ground wire from the GND terminal on the mAT-30 to a suitable station ground.
  5. Auxiliary Power (If Needed): If your transceiver's antenna tuner interface does not provide sufficient power, an external DC 12-15V power supply can be connected to the AUXILIARY POWER input.
MAT-TUNER mAT-30 connected to a Yaesu transceiver

Figure 3: mAT-30 tuner placed on top of a Yaesu transceiver.

3. Operating Instructions

The mAT-30 is designed for simple and efficient operation, mirroring the functionality of original Yaesu tuners.

  • Power On: Once connected, the tuner will power on with your transceiver. The front panel features an 'ONLINE' indicator and a 'POWER' indicator.
  • One-Click Tuning: Tuning is initiated directly from the front panel of your compatible Yaesu transceiver, just as you would with an original tuner. Consult your transceiver's manual for specific tuning procedures.
  • Frequency Tracking: The tuner features automatic frequency tracking. As you change the operating frequency on your mobile radio, the mAT-30 will automatically adjust and match its tuning data to maintain optimal performance.
  • Tuning Speed: A full tuning cycle typically takes no more than 5 seconds. If the tuning parameters for a specific frequency are already stored in memory, the tuner can recall and apply them in less than 0.1 seconds.
  • Memory Channels: The mAT-30 can store up to 16,000 tuning configurations, allowing for rapid recall of previously used settings.

4. Maintenance

The mAT-30 is built with durable materials and high-quality components, requiring minimal maintenance.

  • Cleaning: Keep the unit clean and free from dust. Use a soft, dry cloth for cleaning. Do not use abrasive cleaners or solvents.
  • Environment: Operate and store the tuner in a dry environment, away from extreme temperatures and direct sunlight.
  • Connections: Periodically check all cable connections to ensure they are secure and free from corrosion.

5. Troubleshooting

If you encounter issues with your mAT-30 tuner, consider the following troubleshooting steps:

  • No Power:
    • Ensure the data cable is securely connected between the tuner and the transceiver.
    • Verify the transceiver is powered on.
    • If using auxiliary power, check the power supply and its connection.
  • Tuner Not Responding:
    • Check all RF and data cable connections.
    • Ensure your transceiver is set to use an external antenna tuner.
  • Poor Tuning Performance:
    • Verify antenna connections are secure and the antenna is suitable for the operating frequency.
    • Ensure the RF IN connection from the transceiver is solid.
    • Check your ground connection.

6. Specifications

Feature Specification
RF Power (PEP) 1 - 120W
Tuning Power 5 - 10W
Frequency Range 1.8 - 54 MHz
Memory Channels Up to 16,000
Full Tuning Time ≤ 5 seconds
Storage Tuning Time ≤ 0.1 seconds
Max Power Consumption ≤ 0.5A
Dimensions (LxWxH) 20 x 13 x 4 cm (7.9 x 5.1 x 1.6 inches)
Weight 0.8 Kg (1.8 Lb)
Built-in Battery No
Certification CE

7. User Tips

  • Users have reported that the mAT-30 operates reliably and meets expectations for automatic antenna tuning.
  • The tuner is particularly effective for challenging antenna conditions, capable of adjusting antennas with a VSWR over 3, which can be difficult for other tuners.
  • Always ensure a good ground connection for optimal performance and safety.

8. Warranty and Support

For warranty information and technical support, please refer to the documentation provided with your purchase or contact your retailer. A detailed user manual in PDF format may also be available from the manufacturer or seller.

Manufacturer Information:
Guangzhou Yixin electronic Commerce Co., Ltd.
Guangzhou BaiYun Qu Yixin Road
Contact Phone: 020-62768437

EU Representative:
Cazedis France SAS
9 Rue Des Colonnes, 75002 Paris, France
Phone: 33-153274350

© 2023 MAT-TUNER. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.