1. Introduction
The XIEGU GNR1 is an advanced digital audio noise filter designed to enhance the audio quality of wireless receiving equipment such as radio transceivers, receivers, and radios. It integrates digital noise reduction (NR) and digital filtering (DFL) technologies to effectively minimize background noise, improve the signal-to-noise ratio (SNR), and make signals more identifiable and clear.
This device supports connection to external passive speakers, providing up to 3W audio output power. It features independent adjustment for input and output sound volumes, selectable high/low input impedance, dual audio output ports (3.5mm stereo and RCA), and a headphone output with automatic switching between headphone and speaker output.
2. Package Contents
Please check the package for the following items:
- 1 x XIEGU GNR1 Digital Audio Noise Filter Unit
- 1 x Power Cable
- 1 x Audio Cable
- 1 x User Manual

3. Product Overview
3.1 Front Panel


- POWER Switch: Turns the unit on/off.
- CLIP Indicator: Lights up when the input audio signal is clipping.
- INPUT Knob: Adjusts the input audio volume.
- NR Knob: Adjusts the level of digital noise reduction.
- L-CUT Knob: Adjusts the low-frequency cut-off point for the digital filter.
- H-CUT Knob: Adjusts the high-frequency cut-off point for the digital filter.
- OUTPUT Knob: Adjusts the output audio volume.
- Headphone Jack: 3.5mm stereo output for headphones.
3.2 Rear Panel


- SP 1 (RCA) / SP 2 (3.5mm) Audio Output: Connect to external speakers.
- LINE LO/HI Switch: Output resistance selection key for line output.
- LINE IN (3.5mm) Audio Input: Connect to the audio output of your radio.
- 12V DC Power Socket: Connect the provided power adapter.
4. Setup and Connections
Follow these steps to connect your XIEGU GNR1:
- Power Connection: Connect the provided 12V DC power adapter to the '12V DC' socket on the rear panel of the GNR1 and plug it into a power outlet.
- Audio Input Connection: Use the supplied audio cable to connect the 'LINE IN' port on the GNR1 to the audio output (e.g., speaker out or line out) of your radio transceiver, receiver, or radio.
- Audio Output Connection:
- For External Speakers: Connect your passive speaker(s) to either the 'SP 1' (RCA) or 'SP 2' (3.5mm) audio output ports on the rear panel. The GNR1 can provide up to 3W output power for 8Ω speakers.
- For Headphones: Plug your headphones into the 3.5mm headphone jack on the front panel. The unit will automatically switch output to headphones when connected.
- Output Impedance Selection: On the rear panel, set the 'LINE LO/HI' switch according to your radio's output impedance.
- If your radio (e.g., XIEGU radios like X6100, G90, G1M, X5105) has a low impedance output, select 'LO'.
- For other radios, select 'HI' or 'LO' based on the actual output impedance of your device. High impedance radios cannot use the low impedance output (LO) setting.

5. Operating Instructions
Once connected, operate the GNR1 as follows:
- Power On: Press the 'POWER' switch on the front panel to turn on the unit.
- Adjust Input Volume: Rotate the 'INPUT' knob to adjust the incoming audio signal level from your radio. Ensure the 'CLIP' indicator does not light up continuously, which would indicate signal distortion.
- Apply Noise Reduction (NR): Turn the 'NR' knob clockwise to increase the level of digital noise reduction. Experiment with this setting to find the optimal balance between noise suppression and signal clarity.
- Apply Digital Filtering (DFL):
- L-CUT (Low-Frequency Cut-off): Adjust the 'L-CUT' knob to filter out unwanted low-frequency noise. The adjustment range is 5Hz to 1280Hz.
- H-CUT (High-Frequency Cut-off): Adjust the 'H-CUT' knob to filter out unwanted high-frequency noise. The adjustment range is 500Hz to 5615Hz.
- By combining L-CUT and H-CUT, you can create a custom passband filter to isolate desired audio frequencies.
- Adjust Output Volume: Rotate the 'OUTPUT' knob to set the desired listening volume for your speakers or headphones.
Note: The digital noise reduction and filtering functions work together to improve audio quality. Adjusting these settings requires some experimentation to achieve the best results for different signal conditions.
6. Maintenance
- Keep the device in a dry, dust-free environment.
- Clean the exterior with a soft, dry cloth. Do not use liquid cleaners or solvents.
- Ensure proper ventilation around the unit to prevent overheating.
- Avoid exposing the unit to extreme temperatures or direct sunlight.
- Do not attempt to open the casing or repair the unit yourself, as this will void the warranty.
7. Troubleshooting
- No Power: Ensure the power adapter is securely connected to both the GNR1 and a working power outlet. Check the power switch position.
- No Audio Output: Verify all audio cables are correctly connected. Check the 'INPUT' and 'OUTPUT' volume knobs are not set to minimum. If using headphones, ensure they are fully plugged in. Check the 'LINE LO/HI' switch is set appropriately for your radio.
- Audio Distortion: If the 'CLIP' indicator is constantly lit, reduce the 'INPUT' volume until it no longer clips.
- Noise Reduction Not Effective: Experiment with the 'NR', 'L-CUT', and 'H-CUT' knobs. Different types of noise and signal conditions may require different settings. Ensure the input signal is not already heavily distorted before processing.
8. Technical Specifications
| Parameter | Value |
|---|---|
| Model | GNR1 |
| Brand | XIEGU |
| Digital Denoiser SNR Upgrade Degree | More than 22dB |
| Working Voltage | DC12V±15% |
| Digital Filter Frequency Response Range (L-CUT) | 5Hz~1280Hz |
| Digital Filter Frequency Response Range (H-CUT) | 500Hz~5615Hz |
| Headphone Drive Power | 100mW Max |
| Headphone Output Impedance | 16~64Ω |
| Input Impedance Range | Low impedance 16Ω, High impedance 10kΩ |
| Speaker Output Power | ≥3W (8Ω THD≤0.2%) |
| Speaker Output Impedance | 4~16Ω |
| Dimensions (L x W x H) | 159 x 44 x 143mm (6.3 x 1.7 x 5.6") |
9. User Tips
- Many users find this device very useful for improving their radio hobby experience, especially for reducing background noise.
- For optimal performance, take your time to experiment with the 'NR', 'L-CUT', and 'H-CUT' settings. The ideal configuration can vary significantly depending on the specific radio, antenna, and environmental noise conditions.
- If you find the noise reduction 'not very effective' initially, try adjusting the input gain to prevent clipping and then fine-tune the NR and filter knobs. Sometimes, a subtle adjustment can make a big difference.
10. Warranty and Support
10.1 Warranty
This product comes with a 90-day warranty from the date of purchase. The warranty covers manufacturing defects and malfunctions under normal use. Buyers are responsible for return shipping fees for warranty items. In most cases, only the problem components need to be returned, not the entire package.
Before returning any item, please contact customer support to obtain the return address and instructions. Mark the package as "gift" on the delivery sheet and provide a tracking number. Upon receipt and verification of the issue, the item will be repaired or exchanged.
10.2 Customer Support
For any questions, technical assistance, or warranty claims, please contact the seller or manufacturer's customer support. Providing detailed information about your issue will help expedite the support process.
We value your satisfaction and are committed to resolving any concerns you may have. Please allow us the opportunity to address any problems before considering other actions.