Flipsky 6374

Contents

Flipsky BLDC Belt Motor 6374 Series User Manual

High Power Brushless Motor for Electric Skateboards

1. Introduction

This manual provides essential information for the safe and efficient use of your Flipsky BLDC Belt Motor 6374 series. Designed for high-performance electric skateboard applications, these brushless motors offer robust power and reliability. Please read this manual thoroughly before installation and operation to ensure optimal performance and longevity of your motor.

Two Flipsky 6374 motors, front view, showing the branding and KV rating.
Figure 1: Two Flipsky BLDC Belt Motors 6374 (190KV variant shown).

2. Specifications

The Flipsky BLDC Belt Motor 6374 series comes with various KV options and robust construction. Key specifications are detailed below:

FeatureSpecification
Brand NameFlipsky (SEQURE)
OriginMainland China
KV Options140KV, 170KV, 190KV
Max Power3500 Watts
Max Current85 Amps
Max Volts14S
Max Torque8 Nm
Motor Resistance0.05 Ohm
Number of Poles14
Net Weight980g
Motor Wire Gauge12AWG
Shaft Size Options8mm (Round shaft), 10mm (D shaft)
Recommended ESC3-12S 50A (e.g., FSESC4.12 50A or FSESC 6.6 60A)

3. Key Features

  • Integrated Hall Sensor: The hall sensor is precisely embedded within the motor core, enabling more accurate detection of position and temperature. This ensures precise positioning and a smooth motor start.
  • Internal view of the motor core highlighting the hall sensor placement.
    Figure 2: Hall sensor placement for precise detection and smooth start.
  • Multi-Strand Stator Winding: Utilizes multi-strand winding for superior heat dissipation and to mitigate the skin effect. This design enhances efficiency compared to single-strand windings which can generate more heat.
  • Diagram illustrating multi-strand stator winding versus single-strand winding.
    Figure 3: Multi-strand winding for improved heat dissipation and efficiency.
  • Durable Wiring: Features a 320mm super long 12AWG silicon cable, known for its heat resistance and durability. The cable is packed with a braided sleeve for added protection and a refined appearance.
  • Motor with its long, braided 12AWG silicon cable.
    Figure 4: Long, heat-resistant 12AWG silicon cable with braided sleeve.
  • High-Quality Bearings: Equipped with high-quality NMB brand bearings, featuring a double bearing system on the bottom side and a single bearing on the top for enhanced stability and longevity.
  • Diagram showing the top and bottom NMB bearings of the motor.
    Figure 5: NMB bearings for durability and smooth operation.

4. Setup and Installation

Proper installation is crucial for the performance and safety of your electric skateboard. Follow these guidelines for setting up your Flipsky BLDC motor:

4.1 Motor Mounting

  • The motor uses M4 metric bolts for mounting.
  • When using compatible motor mounts, M4 Socket Cap bolts are recommended.
  • Mounting screws are not included with the motor and must be sourced separately.

4.2 Shaft Type Considerations

  • If you have chosen a motor with a Round Shaft, a key for the keyway is included in the package.
  • If you have chosen a motor with a D Shaft, ensure your pulley system is compatible with a 10mm D-shaped shaft.
Dimensional drawing of the motor with a D-shaft, showing measurements in millimeters.
Figure 6: Dimensional drawing for D-shaft motor (dimensions in mm).
Dimensional drawing of the motor with a Round shaft, showing measurements in millimeters.
Figure 7: Dimensional drawing for Round shaft motor (dimensions in mm).

4.3 Wiring Configuration

Connect the motor wires to your Electronic Speed Controller (ESC) according to the following color code:

  • Blue wire = U (Phase A)
  • Yellow wire = V (Phase B)
  • Green wire = W (Phase C)

Ensure all connections are secure and properly insulated to prevent short circuits.

5. Operating Instructions

Once installed, ensure your ESC is correctly configured for the motor's specifications (KV, pole count, etc.).

  • Always perform a bench test before riding to confirm correct motor rotation and ESC settings.
  • Monitor motor temperature during initial runs. Excessive heat can indicate improper ESC settings or an overloaded system.
  • Avoid operating the motor beyond its maximum voltage (14S) and current (85 Amps) ratings to prevent damage.

6. Maintenance

Regular maintenance will extend the life and performance of your motor:

  • Cleaning: Keep the motor free from dirt, dust, and debris. Use compressed air to clean out any foreign particles.
  • Bearing Inspection: Periodically check the motor bearings for smooth operation. If you notice any grinding or excessive play, consider replacing the bearings.
  • Wire Connections: Ensure all motor and sensor wire connections remain tight and free from corrosion.
  • Shaft Inspection: Check the motor shaft for any signs of bending or damage.

7. Troubleshooting

Here are some common issues and potential solutions:

  • Motor Not Spinning:
    - Check all wiring connections between the motor and ESC.
    - Verify ESC is powered on and correctly configured.
    - Ensure the Hall sensor cable is properly connected (if using sensored mode).
  • Motor Overheating:
    - Check ESC settings; incorrect timing or current limits can cause overheating.
    - Ensure the motor is not overloaded (e.g., too steep a hill, too heavy a load).
    - Verify adequate airflow around the motor for cooling.
  • Unusual Noise/Vibration:
    - Inspect for loose mounting bolts.
    - Check for debris inside the motor.
    - Examine bearings for wear or damage.
  • Inconsistent Performance:
    - Re-calibrate your ESC with the motor.
    - Check battery voltage and health.

8. User Tips

  • ESC Compatibility: Always ensure your Electronic Speed Controller (ESC) is compatible with the motor's voltage and current ratings. An appropriately sized ESC is crucial for optimal performance and to prevent damage.
  • Shaft Type: Pay attention to the shaft type (D-shaft or Round shaft) when ordering and ensure your pulleys or other accessories match the chosen shaft.
  • Sensor Cable: For smoother low-speed operation and startup, ensure the Hall sensor cable is correctly connected to a compatible sensored ESC.

9. Warranty and Support

For any warranty claims, technical support, or inquiries regarding your Flipsky BLDC Belt Motor, please contact the seller or manufacturer directly. Keep your purchase records handy as they may be required for support services.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.