1. Introduction
Thank you for choosing the ETENWOLF Zephyr S5C Air Compressor. This manual provides detailed instructions for the safe and efficient operation of your portable tire inflator. Designed to inflate a wide range of tires and inflatables, this portable power station pump enhances versatility for your outdoor adventures.
Please read all instructions and safety warnings carefully before use to reduce the risk of electric shock, fire, and/or serious injury.
2. Package Contents
Verify that all items are present in the package:
- Zephyr S5C Air Compressor x 1
- Air Chuck x 1
- Presta Valve Adapter x 1
- Inflation Needle x 1
- High-pressure Tapered Nozzle x 1
- USB C to C Cable x 1
- User Manual x 1
- French Copper Adapter x 1
- T-shaped Quick Connector x 1

Image: Contents of the ETENWOLF Zephyr S5C package.
3. Product Overview
Familiarize yourself with the components of the Zephyr S5C Air Compressor:

Image: Labeled diagram of the Zephyr S5C Air Compressor components.
- Unit button
- Light button
- "-" Decrease pressure button
- Mode button
- Start/pause power button
- "+" Increase pressure button
- Center display
- LED work light
- Pressure hose
- Type-C port
- Progress bar
- Presta valve adapter
- Inflation needle
- High-pressure tapered nozzle
- Car mode
- Manual mode
- Pickup truck mode
- Ball mode
- Bicycle mode
- Motorcycle mode
- Pressure unit
- Target input value
- Actual pressure value
- Battery level indicator
- Safety alert symbol
- Temperature protection indicator
4. Setup
4.1 Initial Charging
Before using the inflator for the first time, fully charge it. Connect the inflator to a certified ETENWOLF charger or PD charger using the provided charging cable.
For optimal charging performance, use a 30W PD charger. Battery charging takes approximately 2-2.5 hours to go from 0% to 100% charged.
The battery level indicator (24) is shown by four bars, each representing 25% of capacity. During charging, the display will show the current charge level.
- 0% - 5% charged: Empty battery icon
- 5% - 25% charged: One bar
- 25% - 50% charged: Two bars
- 50% - 75% charged: Three bars
- 75% - 100% charged: Four bars
- Fully charged: Solid four bars
Note: The inflator cannot be used while it is charging. After 2 minutes of inactivity once fully charged, the inflator will automatically shut off.
5. Operating Instructions
5.1 Steps to Inflate
- Remove the Pressure hose (09) from its storage channel.
- Insert the nozzle (09) clockwise into the object being inflated.
- Press the Start/pause power button (05) to activate the machine.
- Press the Mode button (04) to switch among 6 different modes: Car mode (15), Manual mode (16), Pickup truck mode (17), Ball mode (18), Bicycle mode (19), Motorcycle mode (20).
- Select the pressure unit between PSI, KPa, and Bar by pressing the Unit button (01).
- Press the "-" button (03) to decrease or the "+" button (06) to increase the target pressure value.
- Press the Start/pause power button (05) again to start inflation.
- When the inflated item reaches the preset value, the unit will turn off automatically.
Note: A Presta valve adapter (12), an inflation needle (13), and a high-pressure tapered nozzle (14) are located on the back side storage panel.

Image: Visual guide for tire inflation and product dimensions.
Important Notes for Inflation:
- To stop inflation at any time, press the Start/pause power button (05).
- The ETENWOLF system will automatically remember previous pressure settings.
- Double-check the target input value. Setting a wrong value might lead to an inflated item explosion.
- After inflation, the tire temperature will decrease to ambient temperature, causing pressure to drop by 0.5 to 1.5 PSI.
- When finishing pumping a bike tire, quickly remove the hose to prevent air loss.
5.2 Checking Pressure
- Connect the pressure hose (09) to the item to be tested.
- Press the Start/pause power button (05) to power on.
- The head display (07) will show the current pressure.
5.3 Preset Pressure Values
The display shows the target input value (22) in smaller font and the actual pressure value (23) in larger font. The inflator remembers your last target pressure value and unit option, allowing you to change default pressures at any time.
| Mode | Adjustable Pressure Range | Default Pressure |
|---|---|---|
| Car mode | 8.0-50.0 PSI | 35.0 PSI |
| Manual mode | 3.0-160.0 PSI | 30.0 PSI |
| Pickup truck mode | 10.0-85.0 PSI | 35.0 PSI |
| Ball mode | 3.0-16.0 PSI | 8.5 PSI |
| Bicycle mode | 10.0-145.0 PSI | 22.0 PSI |
| Motorcycle mode | 18.0-55.0 PSI | 30.0 PSI |
5.4 LED Work Light
The LED work light (08) is located on the front of the inflator. To turn it on, first power on the machine by pressing the Start/pause power button (05), then press the Light button (02).
The light has four modes:
- Bright flashlight
- Ultra-bright flashlight
- Slow strobe light (light turns on and off)
- SOS signal (3 short strobe signals, followed by 3 long strobe signals, then 3 more short strobe signals, repeated in a loop)
Note: The light automatically turns off after 1 hour. After the first automatic turn-off, you can manually turn on the LED light for a second time. Once manually turned on for the second time, it will not automatically turn off and must be manually turned off.

Image: Zephyr S5C providing emergency LED lighting.
5.5 Power Bank Functionality
The inflator can function as a power bank to charge electronic devices such as phones, tablets, laptops, drones, and cameras. It features a USB-C Output with 30W Max, supporting 5/9V 3A, 12V 2.5A, 15V 2A, and 20V 1.5A.
Note: To use as a power bank, the inflator needs to be powered on. After 3 minutes of charging, the display will only show the battery level to conserve power. After 5 minutes of fully charging the connected devices, the inflator will automatically turn off.

Image: Zephyr S5C showcasing its multi-purpose capabilities including power bank function.
5.6 Pressure Recalibration
Different altitudes can cause variations in pressure by 1-3 PSI. In high altitude areas (especially over 5000 ft/1524 meters), users can recalibrate the pump's pressure sensor.
Recalibration Steps:
- Power on the inflator (05).
- Hold the Light button (02) and Mode button (04) for 10 seconds.
- When the entire screen flickers, recalibration is complete.
Note:
- Power off the pump before calibration.
- The Pressure hose (09) should not be connected to any item. Any item applying pressure to the hose will disable the recalibration process.
- A charged battery or other power source is required for recalibration.
- There is no memory for new recalibration settings. Once powered off, it will reset to sea level calibration (altitude 0 ft/meters).
6. Maintenance
- Store the product in a dry and clean environment. Avoid intrusion of sand and dust, which can cause damage. Do not wash the product with water.
- Store the product within temperatures ranging from -10°C to 60°C (14°F to 140°F). Extremely hot or cold environments can damage the battery and shorten the inflator's lifespan.
- Long-term storage can reduce battery effectiveness. Charge the inflator at least once every three months to maintain performance.
7. Troubleshooting
| Problem | Solution |
|---|---|
| Slow inflation speed |
|
| Air compressor turns on, but does not inflate |
|
| Unable to increase or decrease the preset pressure |
|
| Inflator inflates but pressure shown on display is zero | If the air pressure is under 3 PSI, the pressure displayed will show zero due to the pump's minimum pressure range. |
| Battery level indicator is different when inflating compared to standby state | The lithium battery's voltage level significantly drops when discharging power, causing the battery level indicator to have a different display when inflating compared to a standby state. This is a normal situation. |
| Battery level indicator does not show on screen after charging | Use a certified ETENWOLF charger or standard charger, and the included charging cable, and try to charge it. |
| Air leakage when connecting high-pressure air hose | Tighten the air nozzle. |
| Unable to charge other devices |
|
| Safety alert symbol (E08 error code) | If the issue persists after shutting down and restarting, send the device for factory repair. |
| E10 error code (Motor malfunction warning) | Motor ceases to function. After flashing for 30 seconds, it should return to normal. If the issue persists after shutting down and restarting, send the device for factory repair. |
| E11 error code (Low-temperature charging protection) | Temperature during charging is too low. Restore temperature to above 0°C (32°F) before continuing charging. |
| E12 error code (High-temperature charging protection) | Temperature during charging is too high. Restore temperature to below 45°C (113°F) before continuing charging. |
| E13 error code (Low-temperature discharge protection) | Temperature during inflation or charging other devices is too low. Restore temperature to above -20°C (-4°F) before continuing. |
| E14 error code (High-temperature discharge protection) | Temperature during inflation or charging other devices is too high. Restore temperature to below 58°C (136.4°F) before continuing. |
| E15 error code (Air pump exceeded working time) | Warning icon flashes for 30 seconds before returning to normal. Check if the inflated item has any leakage. |
| E16 error code (Overpressure protection) | Returns to normal after pressure release. |
| E17 error code (High-pressure operation exceeded working time) | Warning icon flashes for 30 seconds before returning to normal. Check if the inflated item is functioning abnormally. |
| E18 error code (Battery damage warning) | Device will shut down after 30 seconds of flashing. Send the device for factory repair. |
8. Specifications
| Name | Air Inflator |
|---|---|
| Model | Zephyr S5C Air Compressor |
| Dimensions | 162 x 205 x 120mm (6.38 x 8.07 x 4.72 inches) |
| Inflation pressure range | 3.0-160.0 PSI / 0.20-11.00 Bar |
| Operating Temperature | Charging: 0°C-45°C (30°F-113°F) Discharging: -20°C-74°C (-4°F-165°F) |
| Storage temperature | -10°C-60°C (14°F-140°F) |
| High pressure air tube length | 0.9 meters (35.4 inches) |
| Battery capacity | 15600mAh for S5C |
| Working noise | Lower than 85dB within 1 meter |
| Input | Type-C: PD 5V 3A, 9V 3A, 12V 2.5A, 15V 2A, 20V 1.5A |
| Output | Type-C: PD 5V 3A, 9V 3A, 12V 2.5A, 15V 2A, 20V 1.5A |
| Charging time | 30W 2 hours |
| Continuous working time | Approximately 25 minutes at a pressure range of 20-50 PSI, in a 25°C ambient temperature, under full charge |
| Sensor accuracy | ±1 PSI |
9. User Tips
- Fast Inflation: Users report quick inflation times, making it efficient for various tire types.
- Air Release Function: The device can release air pressure, which is useful for fine-tuning tire pressure.
- Large Battery Capacity: The 15600mAh battery provides extended use and power bank functionality.
- Operating Noise: Be aware that the inflator produces some noise during operation.
10. Safety Warnings
Warning! Please read all safety warnings and instructions to reduce the risk of electric shock, fire, and/or serious injury.
- This product is not a toy and should not be used by children. Users must be above 16 years old. Keep a safe distance between children and the inflator while inflating.
- Do not place the product into fire or dump the built-in lithium battery.
- Overheating or water ingress may increase the risk of fire or explosion. Keep the product away from heat sources and do not leave it for prolonged periods in a hot car. If the inflator becomes very hot, there is a risk of explosion.
- The product has a built-in DC motor which may generate sparks during operation. Do not use it in an environment with dust or gas that is liable to explode.
- If there is an unusual noise or the temperature becomes very high during inflation, turn off the inflator immediately.
- Before setting the inflation pressure value, ensure the pressure unit is correctly selected. Mixing up PSI and Bar could lead to dangerous overinflation.
- Do not leave the pump unattended while it is in operation.
- To reduce the risk of electric shock, do not expose to rain. Store indoors.

Image: Nine protection features of the Zephyr S5C.
11. Warranty and Support
11.1 2-Year Warranty Coverage
Within two years of purchase, ETENWOLF provides timely and effective online after-sale service. The company will repair or replace any defective product (due to manufacturing fault) within this warranty period.
11.2 Contact Information
For questions, comments, or support, please contact:
- Phone: (+1) 866-720-9226 (Mon-Fri 8AM-5PM PST)
- Email: support@etenwolf.com
- Website: https://etenwolf.com
- Facebook: www.facebook.com/etenwolftools
Register your product at https://etenwolf.com to receive a 1-year extended warranty.
Manufacturer: Guangdong Bestek Technology Co., Ltd
Brand Owner: Mozhen Technology (Shenzhen) Co., LTD
Made in P.R.C
