MiBOXER SPIR3

Contents

MiBOXER SPIR3 3-in-1 SPI LED Controller User Manual

Model: SPIR3

1. Introduction

The MiBOXER SPIR3 3-in-1 SPI LED Controller is an advanced lighting control system designed for pixel LED strips. It supports single color, RGB, and RGBW output modes, offering versatile control over your lighting installations. Utilizing 2.4GHz wireless transmission technology, it ensures high-speed communication, strong anti-interference capabilities, and a stable signal. This controller works seamlessly with compatible C6 remote controls and B6 touch panels (purchased separately) to adjust modes, colors, brightness, and dynamic lighting effects.

MiBOXER 3 in 1 SPI Controller and Remotes
Figure 1: MiBOXER 3-in-1 SPI LED Controller (SPIR3) with C6 Remote and B6 Panel Remote.

2. Safety Information

  • Ensure the input voltage matches the controller's specifications (DC 5-24V).
  • Do not expose the device to moisture or extreme temperatures.
  • Disconnect power before making any connections or performing maintenance.
  • This device is intended for indoor use only.
  • Keep out of reach of children.

3. Product Components

The MiBOXER SPIR3 system typically includes the following components:

  • SPIR3 3-in-1 SPI LED Controller
  • C6 Remote Control (optional, sold separately)
  • B6 Touch Panel Remote (optional, sold separately)
SPIR3 Controller, C6 Remote, and B6 Panel Remote together
Figure 2: SPIR3 Controller, C6 Remote, and B6 Panel Remote.

4. Setup and Installation

4.1 Wiring the SPIR3 Controller

Follow these steps to connect your LED strip to the SPIR3 controller:

  1. **Connect Light Strips:** First, connect the matching light strips to the output terminals of the SPIR3 controller. Ensure correct polarity (V+, GND, DO1, DO2).
  2. **Connect Power Supply:** Connect the DC 5-24V power supply to the input terminals of the controller (V+, V-).
  3. **Optional Push Switch:** A push switch can be connected for additional control, as shown in the diagram.
Wiring diagram for SPIR3 controller with light strip and push switch
Figure 3: SPIR3 Controller Wiring Diagram.

4.2 Remote Control Battery Installation

For the C6 Remote and B6 Touch Panel, install 2x AAA batteries (3V) into the battery compartment. Ensure correct polarity.

C6 Remote control with packaging
Figure 4: C6 Remote Control.
SPI Panel Remote (B6) features and controls
Figure 5: B6 Touch Panel Remote Controls.

4.3 Pairing Remote Controls with SPIR3 Controller

The SPIR3 LED Controller must be paired with a C6 Remote or B6 Touch Panel for control. To pair:

  1. Power on the SPIR3 controller.
  2. Within 1 second of powering on, press the "ON" button on the B6 or C6 remote three times.
  3. The LED strip will blink to indicate successful pairing.
Video 1: MiBOXER SPI LED Controller and Remote Setup and Demonstration. This video demonstrates the wiring, battery installation, and pairing process for the controller and remotes.

5. Operating Instructions

The SPIR3 controller offers various functions through its paired remote controls (C6 or B6). Both remotes feature similar controls for ease of use.

5.1 General Controls (C6 Remote / B6 Touch Panel)

  • **ON/OFF:** Power the LED strip on or off.
  • **Color Selection:** Adjust RGBW colors.
  • **Brightness Adjustment:** Increase or decrease the brightness level.
  • **Speed Adjustment:** Control the speed of dynamic modes.
  • **Mode Selection (M button):** Cycle through 20 dynamic modes.
  • **Scene Saving (S1, S2, S3):** Save and recall up to three custom lighting scenes.
  • **Dynamic Mode Editing:** Short press to change the color of dynamic mode, long press to change the direction of dynamic mode.
SPI Panel Remote (B6) features and controls
Figure 6: B6 Touch Panel Remote Controls.
SPI Remote Control (C6) features and description
Figure 7: C6 Remote Control Features.

5.2 Changing Output Mode (SPIR3 Controller)

The SPIR3 controller supports Single Color, RGB, and RGBW output modes. To change the output mode:

  • Press the "SET" button on the SPIR3 controller once to activate linking mode.
  • Press the "SET" button continuously to cycle through the output modes (Red: Single Color, Green: RGB, Blue: RGBW).
SPIR3 Controller dimensions and connection points
Figure 8: SPIR3 Controller with SET button and indicator.

6. Maintenance

  • **Cleaning:** Use a soft, dry cloth to clean the controller and remotes. Do not use harsh chemicals or abrasive cleaners.
  • **Battery Replacement:** Replace batteries in the remote controls when they no longer respond or the indicator light is dim. Ensure to use 2x AAA batteries for each remote.
  • **Storage:** Store the device in a cool, dry place away from direct sunlight and extreme temperatures when not in use for extended periods.

7. Troubleshooting

ProblemPossible CauseSolution
LED strip not responding to remote.
  • 1. Remote not paired.
  • 2. Low batteries in remote.
  • 3. Out of control range.
  • 1. Re-pair the remote (see Section 4.3).
  • 2. Replace batteries.
  • 3. Move closer to the controller (max 30m).
LED strip not lighting up.
  • 1. No power to controller.
  • 2. Incorrect wiring.
  • 3. Faulty LED strip.
  • 1. Check power supply connection.
  • 2. Verify wiring according to diagram (Section 4.1).
  • 3. Test with a different LED strip if possible.
Colors are incorrect or inconsistent.
  • 1. Incorrect output mode selected.
  • 2. Incompatible LED strip.
  • 1. Change output mode using the "SET" button on the controller (Section 5.2).
  • 2. Ensure your LED strip is compatible with the controller's output modes (Single Color, RGB, RGBW).

8. Specifications

8.1 SPIR3 3-in-1 SPI LED Controller

ParameterValue
Model No.SPIR3
Working VoltageDC 5-24V
OutputMAX 10A
Working Temperature-10~40°C
Output SignalSPI(TTL) 800Kbps
RF2.4GHz
Control Distance30m
Pixel CapacitySingle color: 2048 / RGB: 1536 / RGBW: 1024
Compatible ChipsTM1809, TM1804, TM1812, SK6813, UCS1903, UCS1909, UCS1912, UCS2903, UCS2909, UCS2912, WS2811, WS2812, WS2813, WS2815, SK6812(RGBW), WS2813(RGBW), WS2814(RGBW)
CertificationCCC, EMC, FCC, UL

8.2 SPI Panel Remote (Model: B6)

ParameterValue
Model No.B6
Working Voltage3V (2*AAA Battery)
Standby Power Consumption15μA
Transmission Power6dBm
Transmission Frequency2.4GHz
Working Temperature-10~40°C
Control Distance30m
Size86*86*15mm (Magnetic Holder: 86*86*5mm)

8.3 SPI Remote Control (Model: C6)

ParameterValue
Model No.C6
Voltage3V (AAA * 2PCS)
Transmitting Power6dBm
Standby Power Consumption15μA
Working Temperature-10~40°C
Transmission Frequency2.4GHz
Modulation MethodGFSK
Control Distance30m
Size45*15*140mm

9. User Tips

  • The B6 Touch Panel Remote features a magnetic suction design, allowing it to be easily attached to a magnetic holder or a metal surface for convenient access. It also has an adhesive-backed base for permanent installation by peeling off the backing.
  • For optimal performance, ensure the controller and remote are within the 30m control distance and free from major obstructions.
  • Experiment with the 20 dynamic modes and scene-saving functions to personalize your lighting experience.
Product features of the B6 Panel Remote, including magnetic attachment and adhesive backing
Figure 9: B6 Panel Remote Magnetic and Adhesive Installation.
Magnetic wall-mounted DIY installation example
Figure 10: Example of Magnetic Wall-Mounted Installation.

10. Warranty and Support

The SPIR3 controller comes with a 2-year warranty. Accessories, such as remote controls, typically come with a 3-month warranty. For support or warranty claims, please contact your seller or refer to the product packaging for specific contact information.

This product is certified with CCC, EMC, FCC, and UL standards, ensuring quality and safety.


Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.