1. Introduction
The JIKONG JK-BD4A24S10P is a Smart Active Battery Management System (BMS) designed for 8S-24S Li-ion, LiFePO4, and LTO battery packs. It features a 0.4A active balance current and supports a 100A continuous charge/discharge current. This BMS provides essential protection functions including overcharge, over-discharge, overcurrent, and short circuit protection, ensuring the safety and longevity of your battery system. It also offers intelligent monitoring and control via Bluetooth (BT) and an optional display.

2. Package Contents
Before installation, please verify that all items are present and in good condition.
- 1 x JIKONG JK-BD4A24S10P Smart Active BMS
- 1 x Sampling line (70cm long)
- 1 x NTC temperature sensor (40cm long)
- 1 x Switch key (50cm long)

3. Setup and Wiring
Proper installation and wiring are crucial for the safe and effective operation of the BMS. Always ensure the battery pack is disconnected before performing any wiring.
3.1 General Installation Steps
- Connect all balance cables to the battery cells, ensuring correct polarity and sequence.
- Insert the balance cable into the BMS.
- Connect the B-line (total negative electrode of the battery pack) and the P-line (total positive electrode for charge/discharge) to the BMS.
3.2 Wiring Diagram for 8-String Cells

3.3 Wiring Diagram for 4-String Cells

Note: Always double-check all connections before powering on the system to prevent damage to the BMS or battery pack. Refer to the QR code on the BMS for the latest APP download and detailed instructions.
4. Operating Instructions
The JIKONG Smart Active BMS offers intelligent monitoring and control features.
4.1 Active Balancing
The BMS employs active balancing (lossless balancing) technology. This method achieves voltage balance by transferring energy from cells with higher energy to cells with lower energy, minimizing energy loss. Active balancing operates continuously whenever there is a voltage difference above a set threshold, regardless of whether the battery is charging, discharging, or idle. This ensures a longer lifespan and more stable performance for your battery pack.

4.2 Multi-Screen Display and Data Connection
Monitor your battery system through various interfaces:
- Mobile Phone Bluetooth APP: The 'JIKONG SMART BMS' app supports iOS, Android, and HarmonyOS. It allows real-time monitoring of voltage, current, temperature, State of Charge (SOC), alarms, and cycle counts. The app supports multiple languages and automatically switches with your phone's system language.
- PC Software: For detailed analysis and parameter adjustment, connect the BMS to a computer via an appropriate interface (e.g., RS485). The PC software provides a comprehensive overview and control options.
- Home Storage Dedicated Display: Optional external displays are available for convenient monitoring without a phone or computer.

4.3 Protocol Docking
The JIKONG BMS is compatible with mainstream inverter communication protocols, allowing for seamless integration into various power systems. Supported CAN protocols can be easily set up through the mobile APP or PC software.

5. Maintenance
The JIKONG BMS is designed for durability and high performance. Minimal maintenance is required, but adhering to best practices will ensure its longevity.
- Environmental Protection: The BMS features a fully aluminum alloy shell, which provides superior heat dissipation and reduces damage from the external environment to the electronic components. This casing is made with one-piece molding technology and high thermal conductivity materials.
- Regular Checks: Periodically inspect all wiring connections for tightness and signs of corrosion.
- Software Updates: Keep the mobile app and PC software updated to the latest versions to benefit from new features and performance improvements.

6. Troubleshooting
This section addresses common issues you might encounter with your JIKONG Smart Active BMS.
6.1 Common Protection Triggers
- Overcharge Protection: If the battery voltage exceeds the set overcharge protection voltage, the BMS will stop charging. Check individual cell voltages and charger settings.
- Over Discharge Protection: If the battery voltage drops below the set over-discharge protection voltage, the BMS will cut off discharge. Recharge the battery promptly.
- Overcurrent Protection: If the discharge or charge current exceeds the maximum limit, the BMS will interrupt the circuit. Reduce the load or charging current.
- Short Circuit Protection: In case of a short circuit, the BMS will immediately cut off the current to prevent damage. Identify and resolve the short circuit before restarting.
6.2 Connectivity Issues
- Bluetooth Connection Failure: Ensure Bluetooth is enabled on your mobile device and the BMS is powered on. Try restarting the app or the BMS.
- RS485 Module Compatibility: The JIKONG BMS supports the JK RS485 module. If experiencing issues, ensure the module is correctly connected and configured according to the instructions.
6.3 Balancing Issues
If cell voltages are not balancing effectively, verify that all balance wires are correctly connected and not damaged. The active balancing feature should continuously work to equalize cell voltages.
7. Specifications
The following table details the technical specifications of the JIKONG Smart Active BMS, including various models.

| Feature | Specification |
|---|---|
| Brand Name | JIKONG |
| Model | JK-BD4A24S10P |
| Battery Type | Li-ion, LiFePO4, LTO |
| Battery Strings | 8S-24S |
| Balance Function | Active Balanced BMS |
| Balance Current | 0.4A |
| Charge/Discharge Current | 100A |
| Charge and Discharge Port | Common Port BMS |
| Protection Features | Overcharge Protection, Over Discharge Protection, Overcurrent Protection, Short Circuit Protection |
| Connectivity | Bluetooth (BT), RS485, CAN, NTC |
| Usage Scenario | Power BMS, Energy Storage BMS, 3C Digital BMS |
7.1 Dimensions
The dimensions of the BMS vary slightly by model. For the JK-B1A8S10P (similar form factor to JK-BD4A24S10P), the dimensions are approximately 87mm x 153.9mm x 17.6mm.

8. Warranty and Support
For warranty information, technical support, or service inquiries, please contact JIKONG Smart BMS Store directly or visit their official website. Ensure you have your product model number (JK-BD4A24S10P) and purchase details available when seeking support.
9. User Tips
- RS485 Module: The JIKONG BMS is compatible with the JK RS485 module for enhanced communication and monitoring capabilities. Ensure you use an official JK RS485 module for optimal performance.
- Parameter Adjustment: When adjusting protection values such as overcharge, over-discharge, overcurrent, and temperature, always read the internal parameters of the protection board first before making any changes.
- App Usage: Utilize the mobile app for convenient real-time monitoring and quick adjustments. It provides a clear overview of your battery's status.